Abstract:Lattice structures are emerging as highly effective heat exchange mediums in exchangers and radiators due to their low weight, high specific stiffness and strength, and extensive surface area. These attributes render them particularly suitable for enhancing heat transfer efficiency while maintaining a lightweight and structurally sound design. Certain applications, such as hot stamping, demand both high heat transfer performance and significant load-bearing capacity. Arch micro-strut (ARCH) lattice is a kind of high load-bearing lattice. Currently, there is a gap in the research on its heat transfer performance. This study provides a comprehensive analysis of the heat transfer and mechanical performance of additively manufactured ARCH lattice structures. Deionized water (DI water) was selected as the working fluid in this study. The analysis spans various relative densities, inlet velocities, array orientations, and gradient configurations, employing both experimental and simulation approaches. The results of this study reveal that as relative density increases, the pressure drop gradually rises, while the convective heat transfer coefficient increases before stabilizing. The pressure drop reaches a maximum of 348 kPa at 4 m/s, 40 % relative density, and the convective heat transfer coefficient reaches a maximum of 13,805 W/m2·k at 4 m/s, 20 % relative density. At a relative density of 20 %, the convective heat transfer coefficient reaches its maximum at the same inlet velocity. Specifically, at an inlet velocity of 4 m/s, the convective heat transfer coefficient for a 20 % relative density is 115 % higher than that at 0 %. The maximum Von Mises stress and deformation decrease progressively as relative density increases, from 980.72 MPa to 236.05 MPa, suggesting a substantial enhancement in the compressive properties of the structure. Additionally, a higher inlet velocity results in an enhanced convective heat transfer coefficient. The convective heat transfer coefficient increased by an average of 2300 W/m2·k when the flow rate increased from 1 m/s to 4 m/s. The anisotropic nature of ARCH lattice structure significantly affects mechanical properties and heat transfer efficiency, with the heat transfer coefficient being higher at the inlet along X-direction compared to Z-direction, and a lower pressure drop in X-direction. The gradient structure is shown to effectively address the non-uniform heat dissipation requirements of various components. Specifically, decreasing gradient (DG) configuration offers superior heat transfer performance under similar pressure drop conditions, while increasing gradient (IG) configuration provides better temperature uniformity. Overall, ARCH lattice structure demonstrates superior performance compared to face-centered cubic with vertical strut (FCCZ) structure, with an efficiency index approximately 200 % higher than that of FCCZ structure.

Fluid flow and heat transfer performance for micro-lattice structures fabricated by Selective Laser Melting

Numerical Investigation of the Effects of Lattice Array Structures on Film Cooling Performance

Additive manufactured high-performance topology-optimized lattice structure: Compressive behavior and flow heat transfer characteristics

Thermal Behavior and Mechanical Properties of Different Lattice Structures Fabricated Using Selective Laser Melting

Analyzing heat transfer performance of ARCH lattice microchannel heat exchanger fabricated using selective laser melting

Influence of design parameters on natural convection heat transfer in additively manufactured body centered cubic lattice structures

Topological design of open-cell microstructure with optimal effective thermal conductivity

Effects of different cross-sections of Body Centered Cubic cells on pressure drop and heat transfer of additively manufactured heat sinks

Convective Heat Dissipation with Lattice-Frame Materials

A Lightweight X-type Metallic Lattice in Single-Phase Forced Convection

Comparing endwall heat transfer among staggered pin fin, Kagome and body centered cubic arrays

Optimization Design of Lattice Structures in Internal Cooling Channel of Turbine Blade

Designing High-Porosity Porous Structures with Complex Geometries for Enhanced Thermal Conductivity Using Selective Laser Melting and Heat Treatment

Flow and Heat Transfer Characteristics of a Staggered Array of Kagome Lattice Structures in Rectangular Channels

Heat Insulation Performance of Lattice Thermal Protection Structure with Reinforced Plate

Understanding heat transfer and flow characteristics of additively manufactured pin fin arrays through laser-induced fluorescence and particle image velocimetry

Evaluating Lattice Mechanical Properties for Lightweight Heat-Resistant Load-Bearing Structure Design

Convective Heat Transfer in a Lightweight Multifunctional Sandwich Panel with X-type Metallic Lattice Core

Three-dimensional Lattice Boltzmann study on structure optimization and heat dissipation performance of pin-fin heat sink integrated with phase change material

DEVELOPMENT OF LATTICE MATERIALS WITH HIGH SPECIFIC STIFFNESS AND STRENGTH

Computational Analysis of Turbulent Flow and Heat Transfer in Latticework Cooling Structures under Various Flow Configurations