Abstract:As the performance requirements for lithium-ion batteries (LIBs) increase, it is particularly important to research and develop new electrodes for lithium-ion batteries. In this work, a 3×3×1 supercell of VS 2 are constructed by means of the first-principles method based on density functional theory to study the possibility of using it as an anode material for lithium-ion batteries. Through the analysis of the energy band diagram, it is found that VS 2 has metallic properties. Combined with the density of states diagram, it can be analyzed that the energy band near the Fermi level of VS 2 is contributed by the 3d state of V and the 3p state electrons of S. This means that the conductive properties of VS 2 are largely affected by the 3d state of V and the 3p state electrons of S. Among the vacancies, bridge sites, and top sites, the top site of lithium adsorbing vanadium (V) has the lowest adsorption energy, indicating that lithium will preferentially adsorb the top site of vanadium (V). Through first-principles molecular dynamics simulations of the top position of adsorbed vanadium (V), it was found that at a temperature of 300k, the total energy of the system and the magnitude of the total temperature fluctuation can reach a steady state, indicating that lithium can exist stablyadsorbed vanadium (V) top position. Moreover, the interlayer spacing of the double-layer VS 2 reaches 3.67Å, which is larger than the interlayer spacing of graphene. From the top position to the vacancy, its diffusion barrier is only 0.20eV. The interlayer spacing is larger than double-layer graphene, and the diffusion barrier is lower than graphene, indicating that lithium has very good diffusivity on the VS 2 surface, and lithium can migrate quickly on the VS 2 surface, which is conducive to the rapid charge-discharge process of LIB. In addition to excellent electrical conductivity, VS 2 also has good mechanical properties. The calculated Young's modulus is 96.82 N/m, and the Young's modulus and Poisson's ratio do not decrease after adsorbing lithium, indicating that the rigidity of VS 2 will not be reduced during the diffusion and migration process of lithium. On the other hand, it has excellent deformation resistance. In order to be more accurate and close to the actual situation, a double-layer VS 2 model was constructed, and the maximum number of lithium adsorbed between layers was 18. The calculated theoretical capacity of VS 2 (466 mAh/g) is higher than the theoretical capacity of graphene (372 mAh/g). Our results suggest that VS 2 can be used as a promising anode material for lithium-ion batteries with excellent electrical conductivity and mechanical rigidity.

Vs2/ Blue Phosphorus Composites for High Speed Lithium Ions Storage

Metallic VS2/blue phosphorene heterostructures as promising anode materials for high-performance lithium ion batteries: A first principles study

Blue phosphorene/graphdiyne heterostructure as a potential anode for advanced lithium-ion batteries: First-principle investigation

Black Phosphorene/blue Phosphorene Van Der Waals Heterostructure: a Potential Anode Material for Lithium-Ion Batteries.

Black phosphorus composites with engineered interfaces for high-rate high-capacity lithium storage

First-principles Study of VS2 As Anode Material for Li-ion Batteries

First-principles calculation study of VS 2 as anode material for Li-ion batteries

Lithium Reaction Mechanism And High Rate Capability Of Vs4-Graphene Nanocomposite As An Anode Material For Lithium Batteries

The optimized interface engineering of VS2 as cathodes for high performance all-solid-state lithium-ion battery

VS 4 /MoS 2 heterostructures grown along graphene to boost reaction kinetics and reversibility for high performance lithium-sulfur batteries

Cellulose derived fibrous vanadium-sulfide/carbon composite with enhanced lithium storage properties

Nickel-Sulfide/Vanadium-Sulfide/Carbon Composite Nanofibers for Lithium-Ion Storage

Linking Solid Electrolyte Degradation to Charge Carrier Transport in the Thiophosphate‐Based Composite Cathode toward Solid‐State Lithium‐Sulfur Batteries

Porous Silicon–graphene–carbon Composite As High Performance Anode Material for Lithium Ion Batteries

PEDOT-PSS coated VS2 nanosheet anodes for high rate and ultrastable lithium-ion batteries

Heterogeneous isomorphism hollow SiGe nanospheres with porous carbon reinforcing for superior electrochemical lithium storage

3D Holey Graphene/Polyacrylonitrile Sulfur Composite Architecture for High Loading Lithium Sulfur Batteries

ZnMn2O4/ZnMnO3/ZnO composite with novel bilayer heterojunction structure for enhanced lithium storage performance

Facile Hydrothermal Synthesis of Vs2/Graphene Nanocomposites with Superior High-Rate Capability As Lithium-Ion Battery Cathodes

Interlayer-expanded and Carbon-Coated VS2 Nanosheets Self-Assembled on 3D CNTs Cross-Linked Network Skeleton for Ultrastable Lithium-Ion Storage

Si/C Composites for High Capacity Lithium Storage Materials