Abstract:The autonomous liquid crystalline elastomer (LCE) actuators have garnered increasing attention owing to their ability to sustain continuous motion without the need for external manual control. However, most autonomous LCEs are only capable of achieving self-sustained locomotion under specific single conditions (or within a small temperature range) due to their simplistic chemical design. This study begins with a twisted ribbonshaped autonomous LCE, wherein precise control over the working temperature is attained by manipulating the network cross-linking density and incorporating non-liquid crystal co-monomers. The result shows that the crosslinking density has a significant impact on both the actuation performance and mechanical properties of LCEs, thereby influencing working temperature range and actuation speed. Specifically, as the amount of crosslinkers decreases, the actuation strain increases from 60% to 90% while the Young's modulus decreases from 21 MPa to 6 MPa. Due to the compromise of these two properties, the self-rolling capability would be constrained by either excessively high or low levels of cross-linking densities. The optimal performance is observed when the crosslinker ratio is in a moderate state, resulting in a wider range of actuation temperatures and faster moving speed. Beyond that, the incorporation of non-liquid crystal co-monomers also plays an important role in the actuation of LCEs. Different from the cross-linking density, both actuation performance and mechanical properties decrease significantly as the content of co-monomers increases, leading to a notable reduction in the temperature range required for actuation. The phase transition temperature of LCE even disappears when the co-monomer content exceeds 25 wt%, resulting in a loss of autonomous motion. Overall, the aforementioned methods enable the easy achievement of autonomous LCE actuators with diverse working temperature ranges. Sequential autonomous rolling can be accomplished during both the heating and cooling processes, owing to the distinct actuation temperatures exhibited by different LCE actuators. This tunable working temperature of autonomous LCE actuators will significantly broaden the scope of material design for soft robots. [GRAPHICS] .

Regulating Actuations and Shapes of Liquid Crystal Elastomers Through Combining Dynamic Covalent Bonds with Cooling-Rate-Mediated Control

3D Printing of Reprogrammable Liquid Crystal Elastomers with Exchangeable Boronic Ester Bonds

Programming Actuation Onset of a Liquid Crystalline Elastomer Via Isomerization of Network Topology

Repeatedly Programmable Liquid Crystal Dielectric Elastomer with Multimodal Actuation.

Shape Memory Behaviors of 3D Printed Liquid Crystal Elastomers

Structure-induced Intelligence of Liquid Crystal Elastomers.

Pluralizing actuation behavior of 3D printable liquid crystal elastomers via polymerization sequence control

Shape-Tunable 4D Printing of LCEs via Cooling Rate Modulation: Stimulus-Free Locking of Actuated State at Room Temperature

Locking Alignment of Liquid Crystal Actuators Using Hydrogen Bonds to Enable Room‐Temperature Shape Programmability and Enhanced Work Capacity

Rapidly and Repeatedly Reprogrammable Liquid Crystalline Elastomer via a Shape Memory Mechanism

Thiol-acrylate Catalyst Enabled Post-Synthesis Fabrication of Liquid Crystal Actuators

Programmable 3D Shape-Change Liquid Crystalline Elastomer Based on a Vertically Aligned Monodomain with Cross-link Gradient

Shape Morphing of 3D Printed Liquid Crystal Elastomer Structures with Precuts

Sequentially Autonomous Rolling of Liquid Crystalline Elastomers with Tunable Actuation Temperatures

A simple analytical thermo-mechanical model for liquid crystal elastomer bilayer structures

A Molecular Theory for Liquid Crystal Elastomers: Nematic Ordering, Shape Deformation and Mechanical Response

Dynamic Shape Change of Liquid Crystal Polymer Based on An Order‐Order Phase Transition

Enabling Liquid Crystal Elastomers with Tunable Actuation Temperature

Attenuating Liquid Crystal Elastomers’ Stress Concentration by Programming Initial Orientation

Photo‐Controllable Elongation Actuation of Liquid Crystal Elastomer Films with Well‐Defined Crease Structures

Electrostatically Powered Multimode Liquid Crystalline Elastomer Actuators