Abstract:The development of ceramic-polymer composites is a focal point in the research of thermal protection systems, and the control of microstructure is crucial for fabricating high-performance resins. In order to investigate the effect of the silicon phase structure on the properties of epoxy resins and preparate the ablation-resistant ceramifiable resins, the homogeneous and "sea-island" phases of epoxy resins with different amounts of silicones were prepared by ring-opening and grafting reactions. The reaction mechanism and the microphase structure of silicone were verified by SEM and TEM. It was found that the homogeneous silicone-epoxy resins exhibited exceptional ablation resistance, with mass and linear ablation rates of 0.0646 g/s and 0.0073 mm/s, which were 78.61 % and 98.36 % lower than those of epoxy resins, and exceeded most of the resin-based ablation-resistant materials reported in the literatures. The homogeneous silicone further slows down the pyrolysis rate of the epoxy resin and inhibits the release of pyrolysis products. During the carbonization and ceramization, the carbothermal reduction reaction between silicon and carbon occurs sufficiently in the homogeneous system, which enhanced the content of SiC ceramics in the carbon layer. Eventually, a dense char layer with low porosity and a highly graphitized structure constructed in situ on the ablative surface, which greatly improves the ablative resistance. Furthermore, its exceptional mechanical properties render it capable of substituting conventional resin-based thermal protection materials, thereby meeting the stringent demands of challenging environments.

Simultaneous Improvement of Mechanical, Adhesive and Ablative Properties of Phenolic Epoxy Modified PDMS

Improved Mechanical and Ablative Properties of PDMS Coatings Incorporating Epoxy As a Suspended Chain

Enhanced Mechanical and Adhesive Properties of PDMS Coatings Via In-Situ Formation of Uniformly Dispersed Epoxy Reinforcing Phase

The Improvement of Thermal Stability and Adhesion of Silicone Rubber Composites Modified by Phenolic Epoxy Resin

Cycloaliphatic epoxy-functionalized polydimethylsiloxanes for comprehensive modifications of epoxy thermosets

Improvement of Silicon and Epoxy Phase Interface by Constructing Rigid Interpenetrating Networks Based on Bismaleimide to Enhance Ablative, Mechanical and Thermal Properties

A Novel Phosphorus-Containing Polysiloxane for Fabricating High Performance Electronic Material with Excellent Dielectric and Thermal Properties

Promoted Ablation Resistance of Polydimethylsiloxane Via Crosslinking with Multi-Ethoxy POSS

Morphology and Thermomechanical Properties of Epoxy Thermosets Modified with Polysulfone‐block‐polydimethylsiloxane Multiblock Copolymer

Enhanced Compatibility, Morphology, and Low-Temperature Toughness of Polyamide 6/poly(dimethylsiloxane)/epoxidized Silicone Rubber Composites

Preparation and Ablative Behaviors of Carbon Fiber‐reinforced Polydimethylsiloxane‐co‐poly(silylene Acetylenearyleneacetylene) Composites

The Thermal Stability Investigation of Microencapsulated Ammonium Polyphosphate/siloxane‐modified Epoxy Resin Composites

Enhanced mechanical and adhesive properties of PDMS based on novel PDMS-epoxy IPN structure

Synthesis of a comb-like silicone-epoxy co-polymer with high thermal stability and mechanical properties for ablative materials

Mechanical and thermal degradation behavior of high-performance PDMS elastomer based on epoxy/silicone hybrid network

The Preparation and Properties Study of Polydimethylsiloxane-Based Coatings Modified by Epoxy Resin

A Novel Phosphorus−silicon Containing Epoxy Resin with Enhanced Thermal Stability, Flame Retardancy and Mechanical Properties

Preparation of Ceramifiable and Ablatively Resistant Epoxy Resins by Microphase Structure Modulation of Silicones

Ceramization of Coordinated Zr4+ and Hf4+ in Polysiloxane Conferring Silicone/phenolic Hybrid Resin with Excellent Thermal Protection

Poly(hydroxyether of bisphenol A)-block-polydimethylsiloxane alternating block copolymer and its nanostructured blends with epoxy resin

Effect of Hybrid Cross‐linked Polyphosphazene Microspheres on Ablative and Mechanical Properties of Ethylene Propylene Diene Monomer