Ag3PO4/SnO2 Semiconductor Nanocomposites with Enhanced Photocatalytic Activity and Stability

Lili Zhang,Hengchao Zhang,Hui Huang,Yang Liu,Zhenhui Kang

DOI: https://doi.org/10.1039/c2nj40206h

2012-01-01

Abstract:Ag3PO4/SnO2 semiconductor nanocomposites exhibit much higher photocatalytic activity and good stability than pure Ag3PO4 for the photodegradation of organic compounds (methyl orange) in the absence of electron acceptors under visible light.

What problem does this paper attempt to address?

In-situ Growth of High-Density Ultrafine Ag3PO4 Nanoparticles on 3D TiO2 Hierarchical Spheres for Enhanced Photocatalytic Degradation of Organic Pollutants

Degui Qian,Desheng Fang,Yifeng Xu,Haihua Hu,Ping Lin,Zixuan Ding,Peng Wang,Lingbo Xu,Can Cui

DOI: https://doi.org/10.1088/1361-6528/abb0b9

IF: 3.5

2020-01-01

Nanotechnology

Abstract:Silver phosphate (Ag3PO4, APO) has attracted intense attention as a visible-light-driven photocatalyst, but its large-scale application is limited by severe charge recombination and inevitable photo-corrosion. Various rational APO-based heterostructures composed of APO nanoparticles (NPs) and band-matched semiconductor support are designed to address the above issues. Nevertheless, the size, density, stability, and dispersion of APO NPs are critical challenges for the photocatalytic performance of APO-based photocatalysts. Here, three-dimensional (3D) self-assembled TiO2 hierarchical spheres (THS) prepared by a simple one-step hydrothermal method are employed as innovative support, and ultrafine high-density APO NPs with an average size of about 3 nm are successfully deposited and uniformly dispersed throughout THS to form hierarchical THS/APO composites. The novel THS/APO microstructure provides abundant reactive sites for photocatalytic reactions and promotes the photogenerated charge separation and transfer due to the ultrafine size of APO NPs and the TiO2/APO Type-II heterojunction. As a result, the THS/APO composites show significant improvement in photocatalytic activity and stability in methylene blue (MB) degradation. The reaction constant of THS/APO composites far exceeds that of either THS or APO, roughly 16 and 7 times higher than that of THS and APO under full-spectrum light, and 41 and 4 times higher under visible light. Our results strongly suggest new insights into the low-cost, large-scale application of high-efficiency APO-based photocatalyst.
Ag NPs Modified Plasmonic Z-scheme Photocatalyst Bi4Ti3O12/Ag/Ag3PO4 with Improved Performance for Pollutants Removal under Visible Light Irradiation

Chuanwei Lin,Jianqing Ma,Futao Yi,Huining Zhang,Yongxing Qian,Kefeng Zhang

DOI: https://doi.org/10.1016/j.ceramint.2020.02.266

IF: 5.532

2020-01-01

Ceramics International

Abstract:In a typical Z-scheme photocatalytic system, the visible light responsive component typically plays a crucial role and is often confined to materials sensitive to visible light. In addition, metallic nanodots or quantum dots are used as effective cocatalysts in the construction of plasmonic Z-scheme photocatalysts because of their strong light harvesting capacities under visible light illumination. In the present study, Bi4Ti3O12 nanosheets dominated with (001) crystal planes were successfully prepared via a facile molten-salt method, and BTO/Ag/APO composite samples were prepared by a simple precipitation method followed by photoreduction. The obtained BTO/Ag/APO composite exhibits improved photocatalytic activity for the decontamination of two typical organic pollutants, compared to bare Bi4Ti3O12 and Ag3PO4. Based on various characterization techniques, a Z-scheme electron transfer mechanism induced by the plasmonic effect was hypothesized to clarify the enhanced catalytic performances in this system. On the other hand, the LSPR effect of deposited silver nanoparticles can boost the molecular oxygen activation process and generate more superoxide radicals. This study provides a promising approach to apply highly effective photocatalytic degradation for environmental remediation.
Novel C3N4–CdS Composite Photocatalysts with Organic–inorganic Heterojunctions: in Situ Synthesis, Exceptional Activity, High Stability and Photocatalytic Mechanism

Jie Fu,Binbin Chang,Yanlong Tian,Fengna Xi,Xiaoping Dong

DOI: https://doi.org/10.1039/c2ta00672c

IF: 11.9

2013-01-01

Journal of Materials Chemistry A

Abstract:Novel organic-inorganic composites composed of two visible light responsive semiconductors of graphitic carbon nitride (C3N4) and CdS were successfully synthesized via an "in situ" precipitation-deposition method. The C3N4-CdS heterostructures were fabricated by depositing CdS nanoparticles onto the surface of C3N4. The morphology and optical property of compsoites can be tuned by adjusting the mass ratio of C3N4-CdS, which determines the enhanced level of photocatalytic activity. The optimum activity of 0.7C(3)N(4)-0.3CdS photocatalyst is almost 20.5 and 3.1 times higher than those of individual C3N4 and CdS for the degradation of methyl orange, and 41.6 and 2.7 fold higher for the degradation of 4-aminobenzoic acid, respectively. Moreover, its activity is also much higher than those of C3N4-TiO2 and CdS-TiO2 composites, as well as N-modified TiO2. Of special significance is that the present C3N4-CdS composites exhibit high stabilities under illumination, in contrast with CdS. The enhancement in both performance and stability should be assigned to the effective separation and transfer of photogenerated charges originating from the well-matched overlapping band-structures and closely contacted interfaces. Our work highlights that coupling semiconductors with well-matched band energies provides a flexible route to improve the activity and stability of photocatalysts, and gives ideas for the design and synthesis of other highly active and stable materials.
Synthesis and Characterization of Ag 3 PO 4 /multiwalled Carbon Nanotube Composite Photocatalyst with Enhanced Photocatalytic Activity and Stability under Visible Light

Zhen Wang,Lu Yin,Min Zhang,Guowang Zhou,Hui Fei,Huixiang Shi,Hongjun Dai

DOI: https://doi.org/10.1007/s10853-013-7841-4

IF: 4.5

2013-01-01

Journal of Materials Science

Abstract:A novel Ag3PO4/multiwalled carbon nanotube (Ag3PO4/MWCNT) composite has been prepared by a simple precipitant approach. The obtained samples were characterized by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray, UV–Vis diffuse reflectance, and Raman spectroscopy. It is found that the MWCNTs are well deposited on Ag3PO4 nanoparticles. The Ag3PO4/MWCNT composite with MWCNT content of 1.4 wt% exhibits optimal photocatalytic activity under visible light. The rate constant of MO degradation over Ag3PO4/1.4 wt% MWCNT is 5.84 times that of pure Ag3PO4. Compared with pure Ag3PO4, the incorporation of MWCNTs not only significantly enhances the photocatalytic activity but also improves the structural stability of Ag3PO4, suggesting that the synergistic effects take place in the composite. The improvement is attributed to the conductive structure supported by MWCNTs, which favors electron–hole separation and the removal of photogenerated electrons from the decorated Ag3PO4. A possible photocatalytic mechanism of the Ag3PO4/MWCNT photocatalyst was assumed as well.
Synthesis of Ag3PO4/Ag/g-C3N4 Composite for Enhanced Photocatalytic Degradation of Methyl Orange

Qingwang Liu,Ying Meng,Qiman Liu,Mai Xu,Yunhu Hu,Shikun Chen

DOI: https://doi.org/10.3390/molecules28166082

IF: 4.6

2023-08-17

Molecules

Abstract:In this study, we have successfully constructed Ag3PO4/Ag/g-C3N4 heterojunctions via the hydrothermal method, which displays a wide photo-absorption range. The higher photocurrent intensity of Ag3PO4/Ag/g-C3N4 indicates that the separation efficiency of the photogenerated electron–hole pairs is higher than that of both Ag3PO4 and Ag/g-C3N4 pure substances. It is confirmed that the efficient separation of photogenerated electron–hole pairs is attributed to the heterojunction of the material. Under visible light irradiation, Ag3PO4/Ag/g-C3N4-1.6 can remove MO (~90%) at a higher rate than Ag3PO4 or Ag/g-C3N4. Its degradation rate is 0.04126 min−1, which is 4.23 and 6.53 times that of Ag/g-C3N4 and Ag3PO4, respectively. After five cycles of testing, the Ag3PO4/Ag/g-C3N4 photocatalyst still maintained high photocatalytic activity. The excellent photocatalysis of Ag3PO4/Ag/g-C3N4-1.6 under ultraviolet-visible light is due to the efficient separation of photogenerated carriers brought about by the construction of the Ag3PO4/Ag/g-C3N4 heterostructure. Additionally, Ag3PO4/Ag/g-C3N4 specimens can be easily recycled with high stability. The effects of hydroxyl and superoxide radicals on the degradation process of organic compounds were studied using electron paramagnetic resonance spectroscopy and radical quenching experiments. Therefore, the Ag3PO4/Ag/g-C3N4 composite can be used as an efficient and recyclable UV-vis spectrum-driven photocatalyst for the purification of organic pollutants.

chemistry, multidisciplinary,biochemistry & molecular biology
Graphene Quantum Dots Modified Ag3PO4 for Facile Synthesis and the Enhanced Photocatalytic Performance

Zhigang Chen,Zhenzhen Zhao,Jinyuan Liu,Xingwang Zhu,Liang Wang,Yuanguo Xu,Hui Xu,Huaming Li

DOI: https://doi.org/10.1080/22243682.2018.1459207

2018-01-01

Journal of the Chinese Advanced Materials Society

Abstract:The graphene quantum dots (GQDs) with outstanding electron conductivity and good optical properties modified Ag3PO4 composites were prepared by a simple two-step method. Compared to pure Ag3PO4, the GQDs/Ag3PO4 composites exhibited enhanced photocatalytic activities for degradation Rhodamine B (RhB) and 4-Chlorophenol (4-CP) under the visible-light irradiation. More interestingly, the stabilities of Ag3PO4 were also been improved after introducing GQDs. The possible reaction mechanism was proposed by discussing comprehensive characterizations, which indicated that the GQDs can work as electron acceptors to enhance separation efficiency of photogenerated electron-hole pairs. The structure-activity relationships have been studied in detail. The active species was determined and photocatalytic mechanism was proposed.
A Stable Ag3PO4@g-C3N4 Hybrid Core@shell Composite with Enhanced Visible Light Photocatalytic Degradation

Li Liu,Yuehong Qi,Jinrong Lu,Shuanglong Lin,Weijia An,Yinghua Liang,Wenquan Cui

DOI: https://doi.org/10.1016/j.apcatb.2015.10.035

2015-01-01

Abstract:Ag3PO4@g-C3N4 core@shell composites were prepared via an ultrasonication/chemisorption method. The degradation of methylene blue (MB) over Ag3PO4@g-C3N4 composites was investigated to evaluate their photocatalytic performance. The Ag3PO4@g-C3N4 sample presented the best photocatalytic activity, degrading 97% MB after irradiation for 30 min. Superior stability was also observed in the cyclic runs. The composite has excellent photocatalytic activity and photo-stability and the optimal content of g-C3N4 in the composites is 7.0 wt.%. The efficient photo-generated charge separation originated from a strong interaction in the intimately contact interface, which was confirmed by the results of photocurrent and EIS measurements. Based on the experimental results, a photocatalytic mechanism for organics degradation over Ag3PO4@g-C3N4 photocatalysts was proposed. (C) 2015 Elsevier B.V. All rights reserved.
Ag3PO4-anchored La2Ti2O7 nanorod as a Z-Scheme heterostructure composite with boosted photogenerated carrier separation and enhanced photocatalytic performance under natural sunlight

Xiaojuan Chen,Jieming Chen,Ning Li,Ning Li,Jiesen Li,Jiesen Li,Juhua He,Juhua He,Song Xu,Yanping Zhu,Liang Yao,Yiqi Lai,Runliang Zhu

DOI: https://doi.org/10.1016/j.envpol.2023.121322

IF: 8.9

2023-04-15

Environmental Pollution

Abstract:Developing wide spectra-responsive photocatalysts has attracted considerable attention in the photocatalytic technology to achieve excellent catalytic activity. Ag3PO4, with strong response to light spectra shorter than 530 nm, shows extremely outstanding photocatalytic oxidation ability. Unfortunately, the photocorrosion of Ag3PO4 is still the biggest obstacle to its application. Herein, the La2Ti2O7 nanorod was used to anchor Ag3PO4 nanoparticles in this study, and a novel Z-Scheme La2Ti2O7/Ag3PO4 heterostructure composite was constructed. Remarkably, the composite showed strong responsive to most of the spectra in natural sunlight. The Ag0 formed in-situ acted as the recombination center of photogenerated carriers, which promoted their efficient separation and contributed to the improved photocatalytic performance of the heterostructure. When the mass ratio of Ag3PO4 in the La2Ti2O7/Ag3PO4 catalyst was 50%, the degradation rate constant of Rhodamine B (RhB), methyl orange (MO), chloroquine phosphate (CQ), tetracycline (TC), and phenol under natural sunlight irradiation were 0.5923, 0.4463, 0.1399, 0.0493, and 0.0096 min−1, respectively. Furthermore, the photocorrosion of the composite was greatly inhibited, 76.49% of CQ and 83.96% of RhB were still degraded after four cycles. Besides, the holes and O2•− played a significant role in RhB degradation, and it included multiple mechanisms of deethylation, deamination, decarboxylation, and cleavage of ring-structures. Moreover, the treated solution can also show safety to the water receiving environment. Overall, the synthesized Z-Scheme La2Ti2O7/Ag3PO4 composite exhibited immense potential for removing various organic pollutants through photocatalytic technology under natural sunlight irradiation.

environmental sciences
AgVO3/Ag6Si2O7 nanocomposites with enhancing visible-light driven photocatalysis performance

Ziwei Chen,Mengke Li,Yanyan Cui,Yaling Wang

DOI: https://doi.org/10.1016/j.mtsust.2023.100591

IF: 7.244

2023-12-01

Materials Today Sustainability

Abstract:The AgVO3/Ag6Si2O7 nanocomposite was developed via the coprecipitation method. After being composited, these two nanostructures developed a heterojunction form. The DRS spectra suggested that these nanocomposites with different ratios possessed suitable bandgap, therefore could strongly absorb visible light. The EIS and Mott−Schottky plot curves show that the AgVO3 structure was n-type conductivity semiconductor, while the Ag6Si2O7 structure was p-type conductivity, and these two semiconductors could form the p-n heterojunction nanostructure. The AgVO3/Ag6Si2O7 nanocomposite possess higher photogenerated carrier transfer efficiency and stability of the photogenerated carriers. The organic dye photodegradation activity studies suggested that the AgSV-12 exhibited the best photocatalysis effectivity, and showed good photodegradation activity to other organic dyes. The ESR and reactive species quenchers study suggested that the reactive species that oxidized the organic dyes were photogenerated holes, •O2 − and •OH, and the photogenerated holes played the essential factor. Finally, the photocatalysis mechanism and process were presumed as the p-n heterojunction mechanism.

materials science, multidisciplinary,green & sustainable science & technology
Construction of Z-scheme Ag3PO4/Bi2WO6 Composite with Excellent Visible-Light Photodegradation Activity for Removal of Organic Contaminants

Zhongliao Wang,Taiping Hu,Kai Dai,Jinfeng Zhang,Changhao Liang

DOI: https://doi.org/10.1016/s1872-2067(17)62942-5

IF: 16.5

2017-01-01

Chinese Journal of Catalysis

Abstract:Ag3PO4 has good potential for use in photocatalytic degradation of organic contaminants. However, the activity and stability of Ag3PO4 is hard to sustain because of photocorrosion and the positive potential of the conduction band of Ag3PO4. In this study, A composite consisting of Bi2WO6 nanosheets and Ag3PO4 was developed to curb recombination of charge carriers and enhance the activity and stability of the catalyst. Formation of a Ag3PO4/Bi2WO6 composite was confirmed using X-ray diffraction, energy-dispersive X-ray spectroscopy, and X-ray photoelectron spectroscopy. Photoluminescence spectroscopy provided convincing evidence that compositing Bi2WO6 with Ag3PO4 effectively reduced photocorrosion of Ag3PO4. The Ag3PO4/Bi2WO6 composite gave a high photocatalytic performance in photodegradation of methylene blue. A degradation rate of 0.61 min−1 was achieved; this is 1.3 and 6.0 times higher than those achieved using Ag3PO4 (0.47 min−1) and Bi2WO6 (0.10 min−1), respectively. Reactive species trapping experiments using the Ag3PO4/Bi2WO6 composite showed that holes, ·OH, and ·O2− all played specific roles in the photodegradation process. The photocatalytic mechanism was investigated and a Z-scheme was proposed as a plausible mechanism.
Ag–CuO–ZnO Metal–semiconductor Multiconcentric Nanotubes for Achieving Superior and Perdurable Photodegradation

Kaichen Xu,Jiagen Wu,Chuan Fu Tan,Ghim Wei Ho,Ang Wei,Minghui Hong

DOI: https://doi.org/10.1039/c7nr03279j

IF: 6.7

2017-01-01

Nanoscale

Abstract:Solar energy represents a robust and natural form of resource for environment remediation via photocatalytic pollutant degradation with minimum associated costs. However, due to the complexity of the photodegradation process, it has been a long-standing challenge to develop reliable photocatalytic systems with low recombination rates, excellent recyclability, and high utilization rates of solar energy, especially in the visible light range. In this work, a ternary hetero-nanostructured Ag-CuO-ZnO nanotube (NT) composite is fabricated via facile and low-temperature chemical and photochemical deposition methods. Under visible light irradiation, the as-synthesized ZnO NT based ternary composite exhibits a greater enhancement (∼300%) of photocatalytic activity than its counterpart, Ag-CuO-ZnO nanorods (NRs), in pollutant degradation. The enhanced photocatalytic capability is primarily attributed to the intensified visible light harvesting, efficient charge carrier separation and much larger surface area. Furthermore, our as-synthesised hybrid ternary Ag-CuO-ZnO NT composite demonstrates much higher photostability and retains ∼98% of degradation efficiency even after 20 usage cycles, which can be mainly ascribed to the more stable polar planes of ZnO NTs than those of ZnO NRs. These results afford a new route to construct ternary heterostructured composites with perdurable performance in sewage treatment and photocorrosion suppression.
Carbon quantum dots/Ag3PO4 complex photocatalysts with enhanced photocatalytic activity and stability under visible light

Hengchao Zhang,Hui Huang,Hai Ming,Haitao Li,Lili Zhang,Yang Liu,Zhenhui Kang

DOI: https://doi.org/10.1039/c2jm30703k

2012-01-01

Journal of Materials Chemistry

Abstract:In this study, we report the facile fabrication of Ag3PO4, CQDs/Ag3PO4, Ag/Ag3PO4 and CQDs/Ag/Ag3PO4 photocatalysts (CQDs, carbon quantum dots). For CQDs/Ag3PO4 and CQDs/Ag/Ag3PO4, because of the insoluble, photoinduced electron transfer, upconversion luminescence and electron reservoir properties of CQDs, the complex photocatalysts exhibit enhanced photocatalytic activity and structural stability over the photodecomposition of organic compounds (methyl orange) under the irradiation of visible light. Furthermore, the synergistic effect of CQDs and the intense surface plasmon resonance of Ag lead to the highest photocatalytic activity of CQDs/Ag/Ag3PO4 among Ag3PO4 and the corresponding complex photocatalysts. Our results provide an invaluable methodology for designing high-performance photocatalysts based on CQDs and related functional materials, which is promising for catalytic and new energy applications.
Nanocomposite of attapulgite-Ag3PO4 for Orange II photodegradation

Jianfeng Ma,Jing Zou,Liangyin Li,Chao Yao,Yong Kong,Bingying Cui,Runliang Zhu,Dinglong Li

DOI: https://doi.org/10.1016/j.apcatb.2013.06.029

2014-01-01

Abstract:•Well spread Ag3PO4 particles were synthesized in 5nm on attapulgite.•The photocatalytic activity and the stability of Ag3PO4 were improved.•The cost of the treatment for wastewater will be greatly decreased.
AgI/Ag3PO4 heterojunction composites with enhanced photocatalytic activity under visible light irradiation

Jia Yan,Cheng Wang,Hui Xu,Yuanguo Xu,Xiaojie She,Jiajia Chen,Yanhua Song,Huaming Li,Qi Zhang

DOI: https://doi.org/10.1016/j.apsusc.2013.09.113

IF: 6.7

2013-12-01

Applied Surface Science

Abstract:AgI/Ag3PO4 hybrids were synthesized via an ion-exchange method. The structures and morphologies of the samples were characterized by using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), UV–vis diffuse reflectance spectroscopy (DRS) and photoluminescence (PL). The results showed that AgI nanoparticles were uniformly distributed on the surface of Ag3PO4 and the heterostructure was formed. DRS of the AgI/Ag3PO4 composites exhibited strong absorbance in Ultraviolet (UV) and visible regions. PL analysis indicated a more efficient separation of electron–hole pairs in the AgI/Ag3PO4 nanocomposites. Under visible light (λ >400nm), the photocatalytic activity of the AgI/Ag3PO4 composites for photodegradation of rhodamine B were efficient and much higher than that of the pure Ag3PO4 crystals. The enhancing photocatalytic activity of AgI/Ag3PO4 was attributed to the efficient separation of electron–hole pairs derived from the matching band potentials between AgI and Ag3PO4. A photocatalytic mechanism and the photocatalytic reaction kinetics over AgI/Ag3PO4 hybrid materials were also proposed.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Ag3PO4 nanoparticles loaded on 3D flower-like spherical MoS2: a highly efficient hierarchical heterojunction photocatalyst

li wang,yuanyuan chai,jia ren,jing ding,q liu,weilin dai

DOI: https://doi.org/10.1039/c5dt01961c

IF: 4

2015-01-01

Dalton Transactions

Abstract:Novel 3D hierarchical Ag3PO4/MoS2 composites were successfully prepared through a facile and reproducible hydrothermal-in situ precipitation method. The 3D flower-like spherical MoS2 nanoarchitectures acted as an excellent supporting matrix for the in situ growth of Ag3PO4 nanoparticles. The photocatalytic performance of the composites and the effect of the amount of MoS2 were investigated. The obtained hierarchical Ag3PO4/MoS2 composites exhibited significantly enhanced performance for photocatalytic oxidation of Rhodamine B (RhB) compared with pure Ag3PO4 under visible light irradiation. Ag3PO4/MoS2 composites with 15 wt% of MoS2 showed the optimal photoactivity for the degradation of RhB, which was approximately 4.8 times as high as that of pure Ag3PO4. What's more, the optimal Ag3PO4/MoS2 composite also showed better photodegradation efficiency for methyl orange (MO) and p-chlorophenol (4-CP) than pure Ag3PO4. More attractively, the stability of Ag3PO4 was improved after the in situ deposition of Ag3PO4 particles on the surface of MoS2 nanoflakes due to the conductivity of MoS2 itself as electron acceptors. The enhanced performance of the hierarchical Ag3PO4/MoS2 composites under visible light was caused by a synergistic effect including the improved separation of photogenerated charge carriers, boosted light harvesting, a relatively high surface area and matching energy band structures between the two components. Interestingly, the heterostructured Ag3PO4/MoS2 composite reduced the use of the noble metal silver, thereby effectively reducing the cost of the Ag3PO4 based photocatalyst. Ultimately, a MoS2 involved photocatalytic mechanism for the hierarchical Ag3PO4/MoS2 composites was also proposed.
Construction of ZnCo2O4/Ag3PO4 composite photocatalyst for enhanced photocatalytic performance

Jiayi Liu,Jiafeng Hu,Hao Hu,Xiaotao Zhou,Qiwei Wang,Weizhi Wei,Wenhui Liu

DOI: https://doi.org/10.1049/mna2.12202

2024-09-25

Micro & Nano Letters

Abstract:In this study, ZnCo2O4 was prepared by a microwave‐assisted process, and then ZnCo2O4 was loaded onto Ag3PO4 by in‐situ chemical precipitation method to obtain a composite photocatalyst. The catalytic activity and cycle stability were evaluated under visible light, and the catalytic reaction mechanism was proposed. In this study, ZnCo2O4/Ag3PO4 composite catalyst was prepared by the precipitation method, and their performance in the photocatalytic degradation of methyl orange (MO) was studied. The catalysts were characterized by scanning electron microscopy, high‐resolution transmission electron microscopy, X‐ray diffraction, energy‐dispersive X‐ray spectroscopy, selected area electron diffraction, X‐ray photoelectron spectroscopy, and UV‐Vis diffuse reflectance spectroscopy. The results indicate that the 0.1 ZnCo2O4/Ag3PO4 composite system has good photocatalytic activity in the degradation of methyl orange. Under simulated sunlight conditions, the degradation rate can reach 94% after 30 min. The maximum reaction rate constant of 0.1 ZnCo2O4/Ag3PO4 was 0.05301 min−1, which is 3 times and 52 times the rate constant of pure Ag3PO4 and pure ZnCo2O4, respectively. In catalyst recycling experiments, 0.1 ZnCo2O4/Ag3PO4 still degraded methyl orange at a rate of 84.4% after three cycles. Trapping experiments showed that holes and superoxide radicals mostly contributed to the photocatalytic degradation of methyl orange by the catalyst, while hydroxyl radicals played a partial role. The energy level structure of ZnCo2O4/Ag3PO4 is conducive to the effective separation of photogenerated electrons and holes, improving the lifespan of photogenerated charges. In the investigated catalyst series, 0.1 ZnCo2O4/Ag3PO4 demonstrated the best photocatalytic performance.

materials science, multidisciplinary,nanoscience & nanotechnology
Use of a Core-Shell Composite Ag3PO4@TCNQ to Improve Photocatalytic Activity and Stability

Panru Hu,Li Liu,Weijia An,Yinghua Liang,Wenquan Cui

DOI: https://doi.org/10.1016/j.apsusc.2017.07.003

IF: 6.7

2017-01-01

Applied Surface Science

Abstract:We report a composite photocatalyst with a core-shell structure of Ag3PO4@TCNQ (7,7,8,8-Tetracyanoquinodimethane). TCNQ nano-sheet with a conjugated structure was coated on Ag3PO4 particles to enhanced photocatalysis and the stability of Ag3PO4. This composite catalyst can improve the contact area between semiconductors, promote the separation efficiency of electron and hole, and improve photocatalytic activity and stability. Ag3PO4@TCNQ exhibited a high degradation of phenol under visible light. The degradation rate of Ag3PO4@TCNQ (0.3 wt.%) to degradation phenol achieved almost 100% in 12 min, which was about 23% higher than that of pure Ag3PO4. In addition, TCNQ wrapped on Ag3PO4 surface, as the core's protective layer, can effectively improve its stability. After five cycles, the degradation rate still reached 90%, but monomer stability retained only 43%. TCNQ, as a good electron acceptor, can transfer electrons from Ag3PO4 surface well, reduce the reduction of Ag+, and improve the separation efficiency of photogenerated charge, greatly improving the activity and stability of catalyst. TCNQ has a positive position of its energy band relative to Ag3PO4, and the electrons on the Ag3PO4 conduction band can easily transform to the Lowest Unoccupied Molecular Orbital (LUMO) level of TCNQ to realize the efficient separation of charge, which effectively improve quantum efficiency, thus improving activity and stability of catalyst. (C) 2017 Elsevier B.V. All rights reserved.
Photocatalytic degradation of methyl orange by noble metal Ag modified semiconductor Zn2SnO4

Qiang Lu,Zhiqiang Wei,Chao Li,Jinhuan Ma,Ling Li

DOI: https://doi.org/10.1016/j.mssp.2021.106290

IF: 4.1

2022-02-01

Materials Science in Semiconductor Processing

Abstract:Ag/Zn2SnO4 nanometer photocatalysts modified with different content of precious metals were prepared by a one-cloth hydrothermal method. The crystal structure, element valence states and functional groups of Ag/Zn2SnO4 nanometer photocatalyst were characterized and analyzed by XRD, XPS and FT-IR spectra. The morphology and structure of the products were analyzed via SEM and TEM, and their optical properties were characterized by UV–vis and PL spectra. The results show that Ag/Zn2SnO4 nanomaterial has uniform morphology and good dispersibility. Through the degradation experiment of organic dye methyl orange (MO) under an ultraviolet lamp, the photocatalytic performance of 5% Ag/Zn2SnO4 nanomaterial is the best, which is 4.5 times that of Zn2SnO4. Photoelectric chemistry tests show that the modification of Zn2SnO4 by Ag reduces the recombination of electron-hole pairs and increases carrier lifetime. The photocatalytic performance of semiconductor Zn2SnO4 modified with precious metal can be improved effectively.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Preparation Ag3PO4/AgVO3/Ag4V2O7 Composites for Enhancing Visible Light Photocatalytic Activity of Ag3PO4

Meirong Sui,Shuang Zhang,Xiuquan Gu,Meilin Shi,Yong Wang,Linlin Liu

DOI: https://doi.org/10.1007/s10854-018-9462-9

2018-01-01

Journal of Materials Science Materials in Electronics

Abstract:The Ag3PO4/AgVO3/Ag4V2O7 composites were synthesized via a facile solution route for photodegrading the organic pollutants. Specifically, the Ag3PO4 microparticles were dispersed ultrasonically in the NH4VO3 aqueous solution for 3 h, with varying the NH4VO3 volumes for optimizing their photocatalytic (PC) activities. The structure, morphology and optical property of the obtained composites were characterized by using a series of techniques including the XRD, SEM, EDS and UV-Vis spectroscopy, while the PC activities of these samples were examined by evaluating their photodegradation capabilities towards the RhB. It was found that the composites with the NH4VO3 adding volumes of 5 and 20-80 mL displayed higher PC activities than pure Ag3PO4. Of them, the sample with a 60 mL NH4VO3 volume displayed the highest PC activity. The performance enhancement might be attributed to the formation of a heterojunction, leading to the better visible-light harvesting efficiency and the more rapid carrier transport. In addition, the trapping experiments suggested that the electron (e(-)) was the sole active species for the RhB degradation.
Heterostructured Ag3PO4/AgBr/Ag Plasmonic Photocatalyst with Enhanced Photocatalytic Activity and Stability under Visible Light.

Wan-Sheng Wang,Hong Du,Rui-Xia Wang,Tao Wen,An-Wu Xu

DOI: https://doi.org/10.1039/c3nr00191a

IF: 6.7

2013-01-01

Nanoscale

Abstract:A heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalyst was prepared by a rational in situ ion exchange reaction between Ag3PO4 micro-cubes and Br(-) in aqueous solution followed by photoreduction. The photocatalytic activities of obtained photocatalysts were measured by the degradation of methyl orange (MO) and methylene blue (MB) under visible light irradiation (λ≥ 400 nm). Compared to AgBr/Ag, Ag3PO4/AgBr heterocrystals and pure Ag3PO4 crystals, the heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalysts exhibit much higher photocatalytic activity and stability. This enhanced photocatalytic activity suggests that the synergetic effects of the heterostructured Ag3PO4/AgBr/Ag and the strong SPR of Ag NPs on the surface result in the high efficiencies of the photocatalytic activity and the improved stability. With the assistance of Ag3PO4/AgBr/Ag heterostructures, only 8 min and 12 min are taken to completely decompose MO and MB molecules under visible-light irradiation, respectively. Furthermore, the photodegradation rate does not show an obvious decrease during ten successive cycles, indicating that our heterostructured Ag3PO4/AgBr/Ag plasmonic photocatalysts are extremely stable under visible-light irradiation.

Ag3PO4/SnO2 Semiconductor Nanocomposites with Enhanced Photocatalytic Activity and Stability

In-situ Growth of High-Density Ultrafine Ag3PO4 Nanoparticles on 3D TiO2 Hierarchical Spheres for Enhanced Photocatalytic Degradation of Organic Pollutants

Ag NPs Modified Plasmonic Z-scheme Photocatalyst Bi4Ti3O12/Ag/Ag3PO4 with Improved Performance for Pollutants Removal under Visible Light Irradiation

Novel C3N4–CdS Composite Photocatalysts with Organic–inorganic Heterojunctions: in Situ Synthesis, Exceptional Activity, High Stability and Photocatalytic Mechanism

Synthesis and Characterization of Ag 3 PO 4 /multiwalled Carbon Nanotube Composite Photocatalyst with Enhanced Photocatalytic Activity and Stability under Visible Light

Synthesis of Ag3PO4/Ag/g-C3N4 Composite for Enhanced Photocatalytic Degradation of Methyl Orange

Graphene Quantum Dots Modified Ag3PO4 for Facile Synthesis and the Enhanced Photocatalytic Performance

A Stable Ag3PO4@g-C3N4 Hybrid Core@shell Composite with Enhanced Visible Light Photocatalytic Degradation

Ag3PO4-anchored La2Ti2O7 nanorod as a Z-Scheme heterostructure composite with boosted photogenerated carrier separation and enhanced photocatalytic performance under natural sunlight

AgVO3/Ag6Si2O7 nanocomposites with enhancing visible-light driven photocatalysis performance

Construction of Z-scheme Ag3PO4/Bi2WO6 Composite with Excellent Visible-Light Photodegradation Activity for Removal of Organic Contaminants

Ag–CuO–ZnO Metal–semiconductor Multiconcentric Nanotubes for Achieving Superior and Perdurable Photodegradation

Carbon quantum dots/Ag3PO4 complex photocatalysts with enhanced photocatalytic activity and stability under visible light

Nanocomposite of attapulgite-Ag3PO4 for Orange II photodegradation

AgI/Ag3PO4 heterojunction composites with enhanced photocatalytic activity under visible light irradiation

Ag3PO4 nanoparticles loaded on 3D flower-like spherical MoS2: a highly efficient hierarchical heterojunction photocatalyst

Construction of ZnCo2O4/Ag3PO4 composite photocatalyst for enhanced photocatalytic performance

Use of a Core-Shell Composite Ag3PO4@TCNQ to Improve Photocatalytic Activity and Stability

Photocatalytic degradation of methyl orange by noble metal Ag modified semiconductor Zn2SnO4

Preparation Ag3PO4/AgVO3/Ag4V2O7 Composites for Enhancing Visible Light Photocatalytic Activity of Ag3PO4

Heterostructured Ag3PO4/AgBr/Ag Plasmonic Photocatalyst with Enhanced Photocatalytic Activity and Stability under Visible Light.