Abstract:Mechanism analysis, process optimisation and validation of laser surface treatment. Adhesive bonding has gradually replaced mechanical connections as the primary method for composite material bonding, with surface quality being the key factor determining the effectiveness of composite material adhesion. Laser surface treatment, known for its green and precise characteristics, has garnered widespread attention from both academia and industry. However, the process parameters of laser surface treatment are complex, efficiency is low, and the mechanism remains unclear. This paper, based on the response surface methodology (RSM), investigates the influence of laser secondary parameters on the resin removal rate of carbon fiber reinforced polymer/plastic (CFRP) surfaces and the impact of defocusing on surface treatment efficiency. The results indicate that when the total laser energy density (Et) is 69 J/cm2, the overlap ratio in the warp direction (OLs) is 76%, and the overlap ratio in the weft direction (OLh) is 85%, the surface tensile shear strength increases by 90.59% and 27.77% compared to the original surface and polished surface, respectively. When the defocus distance is +8 mm, the efficiency of laser surface treatment is 2.25 times that of non‐defocus, with minimal impact on mechanical performance. The surface treatment mechanism, with changes in Et, primarily involves the pure thermal decomposition of the resin matrix in an oxygen‐free environment, oxidative decomposition, and the synergistic action of the decomposition products' oxidation. Through the coupled optimization of laser process parameters, this work enhances the efficiency and effectiveness of composite material adhesive surface treatment, promoting the engineering application of laser technology. Highlights By establishing a response surface model, the study elucidated the impact patterns of laser secondary parameters (overlap rates in the warp and weft directions, total energy density) on the resin removal rate of CFRP surfaces. Based on the laser surface treatment phenomena at different total energy densities, the study analyzed and revealed the mechanism of near‐infrared (1064 nm) laser resin removal from CFRP surfaces. By increasing the spot size through defocusing, the efficiency of laser surface treatment was enhanced, and the impact on the interfacial properties of CFRP after defocused treatment was validated.

A High Bonding Tensile Strength of CFRP Ultrafast Laser Surface Texturing Method for Surface Damage Repair

Enhancing CFRP Laminates with Plasma Jet Arrays: A Study of Interlaminar Mechanical Properties

Interfacial Strengthening and Self-Monitoring in Carbon Fiber-Reinforced Composites via Carbon Nanotube-Based Damage Sensors

Influence of the different surface treatments on fracture property of CFRP adhesive joint

Laser Cleaning Treatment and its Influence on the Surface Microstructure of CFRP Composite Material

Effect of Laser Surface Treatment on Surface and Bonding Properties of Carbon Fiber Reinforced Composites

Implementation and precision of CFRP geometric configurations before adhesive bonding repair based on 1064 nm infrared pulsed fiber laser ablation

Study on ultrasonic vibration-assisted adhesive bonding of CFRP laminates with laser ablation-treated surfaces

Effect of Mechanical Pretreatments on Damage Mechanisms and Fracture Toughness in CFRP/Epoxy Joints

Enhancing Bond Strength Between Carbon Fiber Reinforced Thermoplastic and Aluminum Alloys Through Laser Surface Treatment

Achievement of High-strength Al/CFRP Hybrid Joint Via High-speed Friction Stir Lap Joining and Laser Texturing Pretreatment Parameters Variation

Nanosecond laser ablation for improving the strength of CFRTP and aluminum alloy adhesively bonded joints

Experiments and modelling of competitive failure behaviour of CFRP stepped-lap repairs with different design parameters

In situ repairing of continuous fiber-reinforced thermoplastic composite via multi-axial additive manufacturing

Process optimization and performance verification of CFRP laser surface modification

Tailoring fiber arrangement in subsurface damage layer of unidirectional CFRP composites by reverse multi-pass cutting

The Effects of Combined Treatments of Laser Engraving, Plasma Spraying and Resin Pre-Coating on Improving the Bonding Strength of Titanium Alloy and Carbon Fiber-Reinforced Polymer

Thermodynamic simulation, surface morphology and bending property of carbon fiber reinforced polymer composite material subjected to laser cleaning

Erosion mechanism and damage behavior of CFRP in plastic abrasive jet machining

Surface Integrity of Water Jet Guided Laser Machining of CFRP

Effect of thermal damage on dynamic and static mechanical properties of CFRP short pulse laser hole cutting