Abstract:Striking a balance between the mechanical properties and electromagnetic interference shielding effectiveness (EMI SE) of Mg alloys stands as a critical concern within the realm of electronics and communications. This study endeavors to optimize the mechanical properties and EMI SE of Mg alloy sheets through a combination of extrusion and rolling (E-R). OM, SEM, XRD, EBSD, and TEM obtained the microstructures of Mg-6Zn-1Y-1La0.5Zr alloys under extrusion and different rolling strain treatments, and the effects of the microstructures on the mechanical properties and EMI SE were revealed. The microstructure of the as-extruded Mg-6Zn-1Y-1La-0.5Zr (abbreviated as ZKL611K) alloy exhibited a distinct bimodal microstructure, with refined dynamically recrystallized (DRXed) grains surrounding coarse unDRXed regions. Subsequent rolling treatments induced a decrease in the aspect ratio of the unDRXed regions, a rapid reduction of DRXed grains, and the accumulation of dislocations within the as-rolled alloy. Statistical analysis of mechanical properties and EMI SE revealed that an optimal balance in the sheets subjected to "extrusion + 37 % rolling reduction", yield strength (YS) of 319 MPa, ultimate tensile strength (UTS) of 375 MPa, and elongation of 12.3 %. Furthermore, the EMI SE ranged from 81 dB to 114 dB within the frequency range of 30-1500 MHz. However, further increments in rolling reduction adversely affected mechanical properties while improving EMI SE. The observed enhancement in mechanical properties can be primarily attributed to the synergistic effects of grain size, second phase, dislocations, low- angle grain boundaries (LAGBs), and texture. Meanwhile, the improved EMI SE can be mainly attributed to the diffuse distribution of the second phase at multiple scales and the modulation of the texture through E-R treatments.

Enhanced Mechanical Properties and Electromagnetic Interference Shielding Effectiveness in Mg-6Zn-1Y-1La-0.5Zr Alloy Sheet by Hot Deformation

Preparation of Mg-6Zn-1La-0.5Zr alloy sheet with excellent mechanical properties and electromagnetic interference shielding effectiveness by extrusion plus rolling

Effect of La content on mechanical properties and electromagnetic interference shielding effectiveness of Mg-Zn-Y-La-Zr alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Enhanced Mechanical Properties of Extruded Mg–Y–Zn Alloy Fabricated Via Low-Strain Rolling

Microstructure and Mechanical Properties of Rolled Mg-12gd-3y-0.4zr Alloy Sheets

Property Improvements in Fine–grained Mg–Zn–Zr Alloy Sheets Produced by Temperature–step–down Multi–pass Rolling

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Effect secondary deformation on microstructures and mechanical properties of Mg-6Gd-3.2Y-xZn-0.5Zr extruded sheet

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Grain refinement and improved mechanical properties of Mg-4Zn-0.5Ca-0.5RE magnesium alloy by thermomechanical processing

Microstructure and Mechanical Properties of Mg–Gd–Y–Zn–Zr Alloy Sheets Processed by Combined Processes of Extrusion, Hot Rolling and Ageing

Effects of Extrusion Ratio on the Microstructure, Texture and Mechanical Properties of Mg-2.5Nd-0.5Zn-0.5Zr Alloy Sheets

Effects of extrusion ratio and temperature on the microstructure and mechanical properties of Mg–Zn–Yb–Zr extrusion alloys

Strength and Ductility Balance on an Extruded Mg–Zn–Ca–La Alloy

The Effect of Y/Er and Zn Addition on the Microstructure and Mechanical Properties of Mg-11Li Alloy