Metal Recovery and Separation from Wastes

Lijun Wang,Shiyuan Liu

DOI: https://doi.org/10.3390/met13081411

IF: 2.695

2023-01-01

Metals

Abstract:With the development of society, large amounts of solid waste (slag, sludge, tailing, electronic waste, etc [...]

What problem does this paper attempt to address?

Progress of Electronic Waste Treatment

Hong-Gang Ni,Eddy Y. Zeng

2014-01-01

Abstract:An introduction was made to several kinds of typical electronic waste and their compositions. The progress of treating technology for the electronic waste was summarized as well, with a detailed description of the separation technique of mechanical treating technology, the dioxin removing process of pyrometallurgical technology, the sulfuric acid bubbling and alkaline leaching processes of hydrometallurgical technology, the amphoteric metal efficient separation technique of low-temperature alkaline smelting technology and the bioleaching and biosorption techniques of biometallurgical technology. Recycling electronic waste in a proper way is of great significance for environmental protection and resource recycling.
A Review on Chemical versus Microbial Leaching of Electronic Wastes with Emphasis on Base Metal Dissolution

Ismail Agcasulu,A. Akcil,Seydou Dembele,S. Panda,Srabani Mishra

DOI: https://doi.org/10.3390/min11111255

IF: 2.5

2021-11-11

Minerals

Abstract:There is a growing interest in electronic wastes (e-wastes) recycling for metal recovery because the fast depletion of worldwide reserves for primary resources is gradually becoming a matter of concern. E-wastes contain metals with a concentration higher than that present in the primary ores, which renders them as an apt resource for metal recovery. Owing to such aspects, research is progressing well to address several issues related to e-waste recycling for metal recovery through both chemical and biological routes. Base metals, for example, Cu, Ni, Zn, Al, etc., can be easily leached out through the typical chemical (with higher kinetics) and microbial (with eco-friendly benefits) routes under ambient temperature conditions in contrast to other metals. This feature makes them the most suitable candidates to be targeted primarily for metal leaching from these waste streams. Hence, the current piece of review aims at providing updated information pertinent to e-waste recycling through chemical and microbial treatment methods. Individual process routes are compared and reviewed with focus on non-ferrous metal leaching (with particular emphasis on base metals dissolution) from some selected e-waste streams. Future outlooks are discussed on the suitability of these two important extractive metallurgical routes for e-waste recycling at a scale-up level along with concluding remarks.

Chemistry,Environmental Science
Research Progress of Heavy Metal Pollution in Municipal Solid Waste

LONG Yu-yang,HU Li-fang,SHEN Dong-sheng,HU Hong

DOI: https://doi.org/10.3969/j.issn.1001-7119.2007.05.030

2007-01-01

Abstract:Distribution and migration of heavy metals in the process of municipal solid waste landfill are reviewed with respect to the solid waste and leachate as an integrated system.Techniques on heavy metals are assessed and development trend of future research in this area are discussed.
Device for Electrochemically Removing and Recycling Heavy Metals in Solid Waste

胡勤海,萧晨霞,田耘,裴毓雯,张旭

2014-01-01

Abstract:The invention discloses a device for electrochemically removing and recycling heavy metals in solid waste. The device comprises an electrochemical reactor, a cathode electrode, an anode electrode and a cation exchange membrane, wherein the electrochemical reactor is a column as a whole; the column consists of an outer column cylinder, an inner column cylinder, a cylindrical bottom plate and two arc-shaped fixing membrane bracket clamping plates; the cathode electrode is arranged in the center of the inner column cylinder; the annular anode electrode is arranged on the inner side of the outer column cylinder in an adhered manner; the fixing membrane clamping plates are semicircular brackets on two sides and used for fixing the cation exchange membrane; the cation exchange membrane is fixed between the inner column cylinder and the arc-shaped fixing membrane bracket clamping plates; a drain tube at the bottom of the electrochemical reactor is positioned in the center of the bottom of the inner column cylinder; a feeding tube and a discharge tube are symmetrically positioned on the outer side of the outer column cylinder and are connected with a pressurizing pump; the cathode electrode and the anode electrode are connected with a power supply. The device has the advantages that the manufacturing cost is low, the operation is simple, the processing efficiency is high, the heavy metals can be separated from wastes and recycled as resources, and the like.
Advances in Recovery of Valuable Metals and Waste Heat from Copper Slag

Zongliang Zuo,Yan Feng,Xinjiang Dong,Siyi Luo,Dongdong Ren,Wenhao Wang,Yuxi Wu,Qingbo Yu,Huan Lin,Xiaoqing Lin

DOI: https://doi.org/10.1016/j.fuproc.2022.107361

IF: 8.129

2022-01-01

Fuel Processing Technology

Abstract:Copper slag, which is produced during the smelting of Cu, contains compounds such as oxides of Fe, Cu, Co, Al, Si, Ni, Cr, and Ca. Cu slag contains more valuable metals, such as Cu and Fe, than those in certain raw ores. The recovery and treatment methods for copper slag are presented in this paper. Considerable attention has been paid to metal recovery over the last few decades. However, this consumes large amounts of energy and its low recovery ratio hinders the development of recovery technologies. Consequently, these technologies are economically impractical and difficult to apply on an industrial scale. The temperature of copper slag derived from furnaces is >1300 degrees C, indicating the potential for recovering a large amount of potential energy. Combined waste heat and metal recovery can be adopted to address the aforementioned issues. However, most fundamental studies on recovery have not included an economic analysis of their technologies. It is worth noting that copper slag can be used as an Fe-adjusting material in cement clinker production owing to its high Fe content. However, metal extraction and waste heat recovery should be performed simultaneously prior to the utilization of Cu slag as a material resource.
Present Situation and Research Progress of Comprehensive Utilization of Antimony Tailings and Smelting Slag

Zeen Yu,Lei Wang,Qi Zheng,Xiaokui Che,Xinglan Cui,Shenyu Wei,Hongxia Li,Xinyue Shi

DOI: https://doi.org/10.3390/su151813947

IF: 3.9

2023-09-21

Sustainability

Abstract:The production process of antimony produces a large amount of solid waste, such as waste rock in mining, tailings in the beneficiation, metallurgical slag in the smelting, and so on. At present, most of these solid wastes are currently in storage, and the storage of a large amount of solid wastes is not only harmful to the local ecological environment but also a waste of resources. In view of this situation, this paper will take antimony tailings and metallurgical slag as examples and summarize them according to their different treatment methods. The comprehensive utilization of antimony tailings is mainly recovering metals by beneficiation and metallurgy and using antimony tailings as building materials and underground filling materials, while the comprehensive utilization method of antimony metallurgical slag is mainly the recovery of valuable metals by pyrometallurgy or hydrometallurgy or the stabilization technology. This paper summarizes the advantages and disadvantages of different treatment methods and puts forward the prospect of future research directions for the treatment of different metallurgical slags and tailings.

environmental sciences,environmental studies,green & sustainable science & technology
Current status and technological progress in lead recovery from electronic waste

Y.-M. Li,Y. Wang,M.-J. Chen,T.-Y. Huang,F.-H. Yang,Z.-J. Wang

DOI: https://doi.org/10.1007/s13762-022-04009-x

2022-04-22

International Journal of Environmental Science and Technology

Abstract:Electronic waste (e-waste) has a complex composition and contains numerous pollutants. Noticeable pollutant is lead, which can affect environment and human health, and has been the focus of increasing attention. It is an essential component of electronic products, and inappropriate disposal of e-waste can result in severe lead pollution. At present, recycling of lead from urban mineral resources, such as spent lead-acid batteries, cathode-ray tube glass, and waste printed circuit boards, has been the major form of lead recovery rather than smelting from the primary ore. Lead is a heavy metal element and can be harmful. Despite measures taken for many years to prevent and control lead poisoning, lead is a hazard that remains an unresolved problem of various e-waste recycling processes. This study presents the current status of lead recovery from e-wastes and electronic equipment and reviews related technological progress. The current status of lead recovery using various types of e-waste treatment technology is discussed, and a range of technological principles, advantages, and disadvantages are analyzed to provide references and new ideas for lead recycling from e-waste.

environmental sciences
Transformation and Detoxification of Typical Metallurgical Hazardous Waste into a Resource: A Review of the Development of Harmless Treatment and Utilization in China

Yuanhang Wang,Haiquan Zhao,Xinyu Wang,Junkai Chong,Xiangtao Huo,Min Guo,Mei Zhang

DOI: https://doi.org/10.3390/ma17040931

IF: 3.4

2024-02-17

Materials

Abstract:The production process of the metallurgical industry generates a significant quantity of hazardous waste. At present, the common disposal method for metallurgical hazardous waste is landfilling, which synchronously leads to the leaching of toxic elements and the loss of valuable metals. This paper presents a comprehensive review of the research progress in the harmless treatment and resource utilization of stainless steel dust/sludge (including stainless steel dust and stainless steel pickling sludge) and aluminum ash (including primary aluminum ash and secondary aluminum dross), which serve as representative hazardous wastes in ferrous metallurgy and nonferrous metallurgy, respectively. Additionally, the general steps involved in the comprehensive utilization of metallurgical hazardous waste are summarized. Finally, this paper provides a prospective analysis on the future development and research trends of comprehensive utilization for metallurgical hazardous waste, aiming to offer a basis for the future harmless, high-value, resource-based treatment of metallurgical hazardous waste and the realization of industrial applications in China.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Review on Comprehensive Recovery Valuable Metals and Utilization of Copper Slag

Jialei Li,Yalong Liao,Haifei Ma,Qingfeng Liu,Yue Wu

DOI: https://doi.org/10.1007/s40831-023-00663-8

2023-03-03

Journal of Sustainable Metallurgy

Abstract:Copper slag, a waste solid produced in the copper smelting process, is a high-quality secondary resource with huge output. The recycling and utilization of copper slag is of great interest because it avoids the loss of valuable metals and the threat of harmful metals, and saves a lot of natural resources and energy. This paper firstly reviews the main methods for the recovery of valuable metals from copper slag, such as beneficiation method, pyrometallurgical approach, and hydrometallurgical process. Then, based on the physical and chemical properties of copper slag, the applications of copper slag in the field of building materials like concrete, cement, inorganic polymers, etc., and functional materials such as catalyst, glass–ceramic, slag wool, thermal energy storage material, etc., were summarized. Finally, the scientific treatment method of copper slag in future is prospected that green, economic, and environmentally friendly sustainable disposal process is the main theme.Graphical Abstract

metallurgy & metallurgical engineering,green & sustainable science & technology
Green Process of Metal Recycling: Coprocessing Waste Printed Circuit Boards and Spent Tin Stripping Solution

Congren Yang,Jinhui Li,Quanyin Tan,Lili Liu,Qingyin Dong

DOI: https://doi.org/10.1021/acssuschemeng.7b00245

IF: 8.4

2017-01-01

ACS Sustainable Chemistry & Engineering

Abstract:Electronic waste (e-waste), including waste printed circuit boards (PCBs), has caused global concern owing to its potential environmental pollution and rich resource content. Previous studies have indicated that urban mining for metals recycling can decrease energy consumption and pollutants emission compared to the extraction of metals from natural minerals. During the production of PCBs, a large amount of spent tin stripping solution (TSS) is simultaneously generated, containing the significant amounts of metal ions and residue nitric acid. In this study, the coprocessing of waste PCBs and spent TSS at room temperature was proposed and investigated, with the aim of developing an environmentally sound process to address these problems. This coprocessing approach proved to be effective. 87% of the Sn-Pb solder, 30% of the Cu, 29% of the Fe, and 78% of the Zn was leached from waste PCBs with spent TSS after 2 h, at room temperature. Moreover, approximately 87% of the electronic components were dismantled from waste PCBs. About 99% of the Sn, Pb, Fe, Cu, and Zn were recovered from the leaching solutions by chemical precipitation. The proposed green process has substantial advantages over traditional recovery methods of heating waste PCBs, in terms of both material and energy efficiency.
Comprehensive Recovery of Multisource Metallurgical Wastes: Recycling Nickel Slag by Aluminum Dross with Converter-Slag Addition

Guangzong Zhang,Nan Wang,Min Chen,Yanqing Cheng

DOI: https://doi.org/10.2355/isijinternational.isijint-2019-670

2020-09-15

ISIJ International

Abstract:Recovery of multisource metallurgical wastes can facilitate the recovery of valuable metals, and achieve the full utilization of slag. Recycling nickel slag by aluminum dross with converter-slag addition was studied. Based on the element mapping of slags, mineral phases in the modified slag were reconstructed under the interaction of nickel and converter slags, and ‘FeO’ could be separated from the relevant structures of the two slags. Element mapping and chemical analysis of the metal phase after reduction indicated that the reduced product was Fe–Cu-based alloy, element mapping and XRD detection of the secondary slag indicated a complex characterization. The influence of factors, including the basicity of the modified slag, the reduction temperature and the Al/‘FeO’ ratio on the recovery degree of Fe, Cu, Mn and P, was discussed and the optimal technical parameter was determined as 1.0, 1773 K and 0.67, respectively.

metallurgy & metallurgical engineering
Electrochemical recovery and high value-added reutilization of heavy metal ions from wastewater: Recent advances and future trends

Liming Yang,Wenbin Hu,Ziwen Chang,Tian Liu,Difan Fang,Penghui Shao,Hui Shi,Xubiao Luo

DOI: https://doi.org/10.1016/j.envint.2021.106512

IF: 11.8

2021-07-01

Environment International

Abstract:<p>Wastewater treatment for heavy metals is currently transitioning from pollution remediation towards resource recovery. As a controllable and environment-friendly method, electrochemical technologies have recently gained significant attention. However, there is a lack of systematic and goal oriented summarize of electrochemical metal recovery techniques, which has inhibited the optimized application of these methods. This review aims at recent advances in electrochemical metal recovery techniques, by comparing different electrochemical recovery methods, attempts to target recycling heavy metal resources with minimize energy consumption, boost recovery efficiency and realize the commercial application. In this review, different electrochemical recovery methods (including E-adsorption recovery, E-oxidation recovery, E-reduction recovery, and E-precipitation recovery) for recovering heavy metals are introduced, followed an analysis of their corresponding mechanisms, influencing factors, and recovery efficiencies. In addition, the mass transfer efficiency can be promoted further through optimizing electrodes and reactors, and multiple technologies (photo-electrochemical and sono-electrochemical) could to be used synergistically improve recovery efficiencies. Finally, the most promising directions for electrochemical recovery of heavy metals are discussed along with the challenges and future opportunities of electrochemical technology in recycling heavy metals from wastewater.</p>

environmental sciences
Multi-Source Ferrous Metallurgical Dust and Sludge Recycling: Present Situation and Future Prospects

Jiansong Zhang,Yuzhu Zhang,Yue Long,Peipei Du,Tielei Tian,Qianqian Ren

DOI: https://doi.org/10.3390/cryst14030273

IF: 2.7

2024-03-14

Crystals

Abstract:Multi-source ferrous metallurgical dust and sludge are significant components of iron-containing solid waste in the iron and steel industry. It is crucial for the sustainable operation of steel enterprises to recycle iron from ferrous metallurgical dust and sludge (FMDS) for use in steel smelting. However, besides Fe, FMDS also contains valuable elements such as Zn, Pb, K, and Na, among others. While these valuable elements hold high recovery value, they impede the direct reuse of FMDS by iron and steel enterprises. This paper introduces the compositional characteristics of multi-source ferrous metallurgical dust and sludge, analyzes the main recycling technologies associated with FMDS at the present stage of development, and discusses the characteristics of different technologies. In view of this, a new idea of the "cooperative treatment of multi-source ferrous metallurgical dust and sludge—full quantitative recovery of valuable elements" is put forward. This new idea integrates a variety of treatment processes to directly recycle FMDS within the steel plant, enhancing the adequacy of dust and sludge recovery and reducing the risk of environmental pollution. This paper provides a reference for achieving the full quantification and utilization of high-value-added FMDS in steel plants.

materials science, multidisciplinary,crystallography
Advanced Recovery Strategies for Metallic and Nonmetallic Fractions from Waste Printed Circuit Boards: A Comprehensive Review

Jie Zhang,Zhengxin Peng,Jiang Wang,Ruiqi Wang,Hui Xu,Shanshan Mao,Wei Deng,Nan Jiang,Qian Feng,Xing Zhou

DOI: https://doi.org/10.1080/15422119.2024.2358481

2024-05-30

Separation and Purification Reviews

Abstract:The recycling approach for waste printed circuit boards (WPCBs) has evolved from stabilization to value-added processes. However, the variability in the value of their components hinders the development of comprehensive WPCB recycling strategies as a whole. This paper reviews advanced recovery strategies for various fractions including base metals, precious metals, rare earth metals, hazardous metals, and nonmetals. The focal points were to elucidate the complex WPCB structure and composition, and the associated recycling challenges, and to evaluate the advanced technologies for the recovery of various fractions. From a forward-looking recycling perspective, the different fractions should be treated separately to minimize environmental impact, recycle product usage, and maximize economic benefits. A comprehensive framework for resource recovery from WPCBs is proposed to guide future research and promote a green, circular economy in electronics waste management.

engineering, chemical,chemistry, analytical, applied
Sustainable Recovery of Metals from E-Waste Using Deep Eutectic Solvents: Advances, Challenges, and Perspectives

Mengwei Guo,Rongrong Deng,Mingyuan Gao,Cunying Xu,Qibo Zhang

DOI: https://doi.org/10.1016/j.cogsc.2024.100913

IF: 9.3

2024-03-16

Current Opinion in Green and Sustainable Chemistry

Abstract:The increasing emission of electronic waste (e-waste) accelerates the depletion of natural metal resources and raises growing concerns for human health and environmental sustainability. Herein, the valuable metal recovery driven by the development of a circular economy has increasingly become a focal point in research. Recovering metals from e-waste can rationally allocate resources and significantly alleviate environmental issues; however, it remains challenging. Deep eutectic solvents (DESs) provide an ideal alternative for these separation and recovery processes due to their green properties. This article reviews recent advances in the recovery of metals from e-waste using DESs, encompassing spent battery materials, printed circuit boards, lamp phosphor waste, and end-of-life permanent magnets. Recovery approaches involving redox/coordination leaching, solvent extraction, precipitation, and electrodeposition are discussed within the framework of DESs' unique solvent characteristics, eco-design principles, and technology features. Finally, challenges facing this emerging recovery technology are outlined while future prospects are also envisioned.

chemistry, multidisciplinary,green & sustainable science & technology
Study on Separation of Iron from Waste Slag of Pyrite Processing

Gui-Fang Zhang,Zhe Shi,Peng Yan,Lei Gao

DOI: https://doi.org/10.1080/01496395.2014.954131

IF: 2.799

2014-01-01

Separation Science and Technology

Abstract:The work presented here investigates the optimum conditions for maximum recovery of iron from the waste slag. The most advantageous option for industrial trial is roasting of the waste slag under reducing condition followed by magnetic separation selected from various options for recovery of iron from the waste slag. The experimental results show that under the treatment condition in this work, about 70% of the iron was recovered from the waste slag, where the iron content in the concentrate is 57%. After further treatment with chlorinated segregation-magnetic separation, the iron content in the recovered slag can reach 83%. After the treatment, sulphur content in the concentrate was reduced significantly and gangue materials, such as SiO2, Al2O3, and TiO2, were reduced effectively. This paper is mainly focused on the results of reduction roasting- magnetic separation. Recovery of iron from the waste slag is of great interest for maximum use of mineral resource, reduction of environment impact, and improvement of economical benefits to the related companies.
Joint utilization and harmless elimination of aluminum dross and refined magnesium slag to simultaneously recover metallic aluminum and fusing agent

Zengwu Wang,Jintao Gao,Xi Lan,Zhancheng Guo

DOI: https://doi.org/10.1016/j.jenvman.2024.121680

Abstract:Refined magnesium slag and aluminum dross are two typical hazardous solid wastes that contain significant amounts of leachable fusing agent and aluminum droplets encapsulated by dense oxidized films, respectively. This study creatively proposes a safe and green method for the joint utilization of these two wastes. The interfacial reaction behavior revealed that the dense oxidized films of the aluminum droplets were significantly broken by the erosive action of the fusing agent, providing the necessary conditions for the movement of aluminum droplets. Consequently, the aluminum droplets successfully broke free from the oxidized films and separated together with the fusing agent from the dross under the force of supergravity. The recovery ratios of metallic aluminum and fusing agent reached 98.95 % and 98.13 %, while the aluminum and fusing agent contents in the tailings were reduced to 0.82 wt% and 3.71 wt%. The study also discusses the leaching characteristic of the tailings and the scalability for industrial applications of this method in detail. This study not only achieves valuable resource recovery but also reduces the leaching risk and alleviates the land occupation and ecosystem pressure caused by industrial wastes. The tailings can be harmlessly utilized in related fields through subsequent scientific treatment.
Liquid-liquid hierarchical separation and metal recycling of waste printed circuit boards

Bin Chen,Jie He,Yaoyao Xi,Xiangfeng Zeng,Ivan Kaban,Jiuzhou Zhao,Hongri Hao

DOI: https://doi.org/10.1016/j.jhazmat.2018.10.022

2019-02-15

Abstract:Waste electrical and electronic equipment is rapidly increasing worldwide, resulting in a large quantity of waste printed circuit boards (WPCBs). There is a great challenge on how to efficiently separate mixed metals in WPCBs, which consists of more than 10 elements including hazardous Cr, Pb and Cd. In this work, based on atomic interactions, a method of liquid-liquid hierarchical separation is developed to separate the mixed metals dissociated from the pyrolyzed WPCBs of mobile phones. The hierarchical separation of L→LFe-rich + LCu,Pb-rich, LCu,Pb-rich→LCu-rich + LPb-rich and LPb-rich→SCu-dendritical + L'Pb-rich produces four immiscible Fe-rich, Cu-rich, Cu-dendritical and Pb-rich substances. The separation rate between these substances can reach more than 96% in a super-gravity field of G = 1000g. Other metals selectively distribute in the four substances. The Fe-rich substance collects Cr, Co, Ni and Si. Almost all of Au and Ag are trapped in the Cu-rich and Cu-dendritical substances. The low-melting-point metals, i.e. Bi, Cd, In and Sn, are located in the Pb-rich substance. This work provides a green shortcut for efficiently separating and recycling overall metals in WPCBs.
Advances in E-Waste Recycling: Physical and Chemical Treatment Methods

Kaiqi Wang

DOI: https://doi.org/10.54097/hset.v73i.13106

2023-11-29

Abstract:The unprecedented rise in production and consumption of electronic devices has resulted in staggering amounts of electronic waste (e-waste). Improper recycling and disposal of e-waste can cause severe environmental and public health repercussions due to the presence of toxic substances like lead, mercury, and flame retardants. This article introduced advanced e-waste recycling technologies, focusing on physical and chemical treatment methods. Physical treatments such as gravity separation, electrostatic separation, and inverse flotation enable efficient and cost-effective recovery of precious metals like gold, silver, platinum, and rare earth metals from e-waste components. These physical processes are often environmentally friendly, scalable, and can handle diverse e-waste streams. Chemical treatments, including the dimethylformamide technique, supercritical fluid technique, and pyrolysis, allow for separating hazardous substances and recovering valuable materials not amenable to physical processes. Supercritical CO2 fluid destroys toxic organic compounds while enabling metal recovery. Pyrolysis converts plastics into liquid oil and gas products. By enhancing the separation and purification of valued materials, these physical and chemical e-waste recycling techniques provide more profitable, efficient, and sustainable solutions to ever-growing e-waste volumes.
[Complications caused by the plastic material used in a 2-stage flexor tendon grafting operation].

D. Veihelmann,P. Schweizer

Abstract:After the use of the silicone-rod method for the two-stage flexor tendon grafting without complications in more than 120 cases, there were found -- although an identical technique was used -- some cases of inflammatory reaction compelling the earlier removal of the rods and leading to poorer results. Tests showed that there are silicone-rubber rods on the market which differ widely in their physical qualities and, therefore, also show differences in their compatibility with tissue.

Metal Recovery and Separation from Wastes

Progress of Electronic Waste Treatment

A Review on Chemical versus Microbial Leaching of Electronic Wastes with Emphasis on Base Metal Dissolution

Research Progress of Heavy Metal Pollution in Municipal Solid Waste

Device for Electrochemically Removing and Recycling Heavy Metals in Solid Waste

Advances in Recovery of Valuable Metals and Waste Heat from Copper Slag

Present Situation and Research Progress of Comprehensive Utilization of Antimony Tailings and Smelting Slag

Current status and technological progress in lead recovery from electronic waste

Transformation and Detoxification of Typical Metallurgical Hazardous Waste into a Resource: A Review of the Development of Harmless Treatment and Utilization in China

Review on Comprehensive Recovery Valuable Metals and Utilization of Copper Slag

Green Process of Metal Recycling: Coprocessing Waste Printed Circuit Boards and Spent Tin Stripping Solution

Comprehensive Recovery of Multisource Metallurgical Wastes: Recycling Nickel Slag by Aluminum Dross with Converter-Slag Addition

Electrochemical recovery and high value-added reutilization of heavy metal ions from wastewater: Recent advances and future trends

Multi-Source Ferrous Metallurgical Dust and Sludge Recycling: Present Situation and Future Prospects

Advanced Recovery Strategies for Metallic and Nonmetallic Fractions from Waste Printed Circuit Boards: A Comprehensive Review

Sustainable Recovery of Metals from E-Waste Using Deep Eutectic Solvents: Advances, Challenges, and Perspectives

Study on Separation of Iron from Waste Slag of Pyrite Processing

Joint utilization and harmless elimination of aluminum dross and refined magnesium slag to simultaneously recover metallic aluminum and fusing agent

Liquid-liquid hierarchical separation and metal recycling of waste printed circuit boards

Advances in E-Waste Recycling: Physical and Chemical Treatment Methods

[Complications caused by the plastic material used in a 2-stage flexor tendon grafting operation].