Abstract:Cyclone separators, which have an important role in the recovery of catalysts, constituted one of the aims of the study. In the work to be done, the pressure drop occurring during the fcc reaction is also calculated using the Ergun equation and it is aimed to provide the same value in a cyclone separator. In this study, which was presented for the first time in the literature, the best working conditions were determined by simulating the pressure drop in the cyclone separator modeled by using the various catalyst types namely NiMo/ASA–Al 2 O 3 , NiMo/p–Al 2 O 3 , NiMo/Y–Al 2 O 3 , Co-Mo, HZSM-5 zeolite, HY zeolite, pAl 2 O 3 , ASA-Al 2 O 3 , Y-Al 2 O 3 determined from the literature in the Ergun equation. Among them, NiMo/ASA Al 2 O 3 , Co-Mo, HY zeolite, and ASA-Al 2 O 3 were determined as the best catalyst for producing diesel from high oil fractions. Unlike previous studies, the condition that the cyclone separator modeled cleans the catalyst with maximum efficiency also determines the condition that provides low catalyst porosity in the determination of the catalyst type to be determined in diesel production. Due to the accuracy between the calculated and the predicted pressure drop results (about 1,8%), HY zeolite is the best catalyst for cyclone separator geometry. It is widely used to convert high molecular weight hydrocarbon fractions, the high boiling point of petroleum crude oils into olefinic gases, more valuable gasoline, and other products. The purpose of the FCC unit is to increase the refinery conversion and white product yield by converting heavy vacuum gas oil (HVGO) into light hydrocarbons at high temperatures with the aid of fluid catalysis. These two zones (reactor and regenerator) are placed as two different pressure vessels. For these two different systems to work in harmony with each other, unlike in previous studies, the "dense discreet phase-Eularian" approach was used in the modeling of the catalytic unit and the "discreet phase" approach was used in the modeling of the cyclone separator. The values required for both processes to work together have been determined approximately.

Optimization of Catalyst Service Cycle and Start-Up Considering the Reactor-Distillation-hen Integration and Climate

Kinetic Model and Simulation Analysis for Toluene Disproportionation and C9-Aromatics Transalkylation

Modeling, Simulation and Optimization of Commercial Naphtha Catalytic Reforming Process

Optimization of the Catalyst Service Life Based on the Coupling of Reactor and Heat Exchanger Network

Simulation, sensitivity analysis and optimization of a continuous catalytic reforming process

System optimization of cyclohexane dehydrogenation under multiphase reaction conditions using the uniform design method

Modeling, Simulation and Optimization of a Whole Industrial Catalytic Naphtha Reforming Process on Aspen Plus Platform

Novel Methodology for Targeting the Optimal Reactor and Operating Parameters Based on the Chemical System’s Overall Performance Within Catalyst Lifecycle

Dynamic Coupling of Reactor and Heat Exchanger Network Considering Catalyst Deactivation

Systematic Optimization Methodology for Simultaneous Process Design and Heat Exchanger Network Synthesis with Surrogate Models – Application to Distillation Column Complex

Dynamic Optimization of the Tandem Acetylene Hydrogenation Process

Coordinated Optimization Control of Flue Gas Temperature for Improving Reaction Efficiency of Catalyst

Optimization of fluid catalytic cracking unit reactor and energy system

Optimization of Solvent and Extractive Distillation Sequence Considering Its Integration with Reactor

Simulative Optimization of Catalyst Configuration for Biogas Dry Reforming

Effect of Catalyst Deactivation on the Energy Consumption of Gasoline–Diesel Hydrotreating Process

Simulation and Optimization of Acetylene Converter with Decreasing Catalyst Activity

Integrated Design And Optimization Of Reactor-Distillation Sequence-Recycle-Heat Exchanger Network

Graphical Optimization Method for Coupled Heat Exchanger Network and Reactor

Optimizing Catalyst Supports at Single Catalyst Pellet and Packed Bed Reactor Levels: A Comparison Study

Developing an adaptive catalyst for an FCC reactor using a CFD RSM, CFD DPM, and CFD DDPM–EM approach