Abstract:The central diaphragm is often used to reduce the span to maintain the stability and safety of structure in the construction of large-span loess tunnel due to the structure complexities. In this paper, relying on the field monitoring and measurement for Wangcun tunnel in Huangling-Yan’an expressway expansion project, the crown settlement and horizontal convergence of primary support steel rib and central diaphragm steel rib during the construction are analyzed by the upper bench CD method. According to the internal force transfer, deformation coordination, and arch foot displacement between the two structures, the support system is regarded as the arch-beam fixed structure with three times of statically indeterminate and movable abutment under the loads, and the mechanical calculation model of sidewall steel rib and the central diaphragm structure bearing loads and deformation together is established. Finally, through the mechanical model mentioned above, the deformation characteristics of central diaphragm structure and the horizontal convergence in the upper bench of tunnel are calculated and analyzed. The research shows the following: (1) the accumulated settlement of sidewall steel rib in Part I is greater than that of the sidewall steel rib in Part II, and the accumulated settlement of each part at the support structure during the tunnel excavation is less than the reserved deformation of 150 mm specified in the tunnel excavation; (2) the settlement located at the waist and maximum excavation line position of central diaphragm is mainly affected by the excavation of Parts I and II in upper bench; (3) during the whole excavation process, the excavation of Part I and Part II has the greatest influence on the convergence at arch waist and the maximum excavation line position in Part I, and the convergence at the above two positions all experienced four stages of “convergence-expansion-convergence-gradual stability”; and (4) the errors between the horizontal convergence and the deformation of central diaphragm obtained by the mechanical model and the field monitoring data are between 12.7% and 27.5%. The calculated results are in good agreement with the actual situation. The research can provide a theoretical basis for the study of deformation and mechanical properties for support structure in the construction of large-span loess tunnel by the upper bench CD method.

Experimental Study on the Failure Mechanism of the Super-Large-span Flat Cavern with the DIC Technique

Instability Mechanism of Shallow Tunnel in Soft Rock Subjected to Surcharge Loads

Physical Model Test and Application of 3D Printing Rock-Like Specimens to Laminated Rock Tunnels

Study of Deformation Behaviors and Mechanical Properties of Central Diaphragm in a Large-Span Loess Tunnel by the Upper Bench CD Method

Understanding the failure mechanism of a large underground cavern in steeply dipping layered rock mass using an enhanced ubiquitous-joint model

Investigation on the failure mechanism of hard rock cavern subjected to adjacent structural plane based on physical model experiments

Stability Analysis of Jointed Rock Mass in Large Underground Caverns Based on Multi-Scale Analysis Method

Critical Failure Characteristics of a Straight-Walled Arched Tunnel Constructed in Sandstone under Biaxial Loading

Deformation and Failure Mechanism Exploration of Surrounding Rock in Huge Underground Cavern

Experimental Investigation on Engineering Disaster Simulation of Deep Buried Cavern Under Impact Load

Experimental Investigation of Strain Rockburst in Circular Caverns under Deep Three-Dimensional High-Stress Conditions

Laboratory Observation of Spalling Process Induced by Tangential Stress Concentration in Hard Rock Tunnel

Experimental Investigation on Failure Mechanism and Rockburst Process of Tunnels Under Different Span-Ratios and Existing Structural Planes

Experimental Investigation of Spalling Failure of D-Shaped Tunnel Under Three-Dimensional High-Stress Conditions in Hard Rock

Macro and micro failure mechanism of surrounding rock of small span tunnel under different stress paths

Experimental and theoretical analysis of spalling in deep hard rock tunnels with different arch structures

Real-time monitoring of the development of brittle fracture in hard rock tunnels based on physical model test

Spalling failure and fracturing of brittle sandstone containing rectangular cavity based on biaxial compression test and discrete element method

The Fracture Evolution Mechanism of Tunnels with Different Cross-Sections under Biaxial Loading

Similarity Model Test on the Spatiotemporal Evolution Law of Deformation and Failure of Surrounding Rock-Induced Caving in Multi-Mined-Out Areas

Stress Analysis and Spalling Failure Simulation on Surrounding Rock of Deep Arch Tunnel