Abstract:A novel method for calculating the critical resolved shear stress (CRSS) ratios of different deformation system types in polycrystalline non-cubic metals has been developed. The mean CRSS ratios between different deformation systems were calculated for both commercially pure (CP) Ti and Ti–5Al–2.5Sn (wt.%) tensile deformed at ambient temperature and 455°C using an in situ scanning electron microscope-based testing technique combined with electron backscattered diffraction. It was found that the relative activity of the different deformation systems changes as a function of alloying composition and deformation temperature. Prismatic slip was the most active deformation mode for CP Ti. CP Ti exhibited a lower resistance to prismatic slip at both ambient and elevated temperatures compared with Ti–5Al–2.5Sn. For Ti–5Al–2.5Sn, prismatic slip was the most active deformation system at ambient temperature although the basal slip activity significantly increased compared to CP Ti, mostly likely due to an increased c/a ratio resulting in a closer packed basal plane. At 455°C, basal slip exhibited a lower CRSS than prismatic slip for Ti–5Al–2.5Sn. The relative activity of other deformation systems was also affected by alloying and temperature. The statistical resampling technique of bootstrapping was used to generate multiple equivalent data sets from which mean CRSS ratios between different deformation systems, and associated confidence intervals, could be deduced. It was found that the mean CRSS ratios at low and high strains varied slightly for the same testing conditions. Moreover, lesser activated slip systems resulted in relatively larger confidence intervals for the CRSS means. This variability may be attributed to a number of potential factors, including measurement errors, rotations of grains during deformation, local stress state variations, and work hardening. The analysis further suggests that awareness of the intrinsic statistical variability in CRSS ratios should be considered when formulating crystal plasticity constitutive models.

Accurate Determination of Active Slip Systems Using a Novel Lattice Rotation Analysis: Quasi-in-situ EBSD/ECCI Study on the Homogeneous/heterogeneous Deformation of Polycrystalline Zirconium

In-situ EBSD Study of the Active Slip Systems and Lattice Rotation Behavior of Surface Grains in Aluminum Alloy During Tensile Deformation

Understanding plasticity in zirconium using in-situ measurement of lattice rotations

In Situ Atomistic Observation of Grain Boundary Migration Subjected to Defect Interaction

An Investigation of Slip and Twinning Behavior of a Zirconium Alloy During Plastic Deformation Based on In-Situ SEM-EBSD

Investigation of Grain Subdivision at Very Low Plastic Strains in A Magnesium Alloy

Identification of active slip systems in polycrystals by Slip Trace - Modified Lattice Rotation Analysis (ST-MLRA)

An SEM/EBSD study of shear bands formation in Al-0.23%wt.Zr alloy deformed in plane strain compression

Characterisation of slip and twinning in high rate deformed zirconium with electron backscatter diffraction

High Strain Gradient Plasticity Associated with Wedge Indentation into Face-Centered Cubic Single Crystals: Geometrically Necessary Dislocation Densities

Tribologically induced crystal rotation kinematics revealed by electron backscatter diffraction

Critical Resolved Shear Stress and Work Hardening Determination in HCP Metals: Application to Zr Single Crystals

Classification of the critical resolved shear stress in the hexagonal-close-packed materials by atomic simulation: Application to α-zirconium and α-titanium

In-situ EBSD investigation of the effect of orientation on plastic deformation behavior of a single crystal superalloy

Methodology for estimating the critical resolved shear stress ratios of α-phase Ti using EBSD-based trace analysis

Assessment of slip transfer criteria for prismatic-to-prismatic slip in pure Ti from 3D grain boundary data

Identification of Active Slip Mode and Calculation of Schmid Factors in Magnesium Alloy

Quantitative characterization of short fatigue crack and grain boundary interaction behavior in zirconium

Tracking the sliding of grain boundaries at the atomic scale

Optimized method for the identification of slip directions in Mg alloy based on intragranular misorientation axes analysis

A Feasible Surface Patterning Method for SEM-DIC: Achieving High-Resolution In Situ Mapping of Local Strain and Microstructure to Reveal the Effect of Slip Transfer on Shear Strain Near Grain Boundaries