Abstract:Two blends between polyamide 6 (PA6) and Polyamide 6co6T (PA6co6T, a random copolymer between polyamide 6 and polyamide 6T) were fabricated by melt-mixing on a twin-screw extruder and the subsequent injection molding, or through the in-situ polymerization of F-caprolactam in the presence of PA6co6T. As far as the former method is concerned, there exist an obvious decline of toughness and a slight increase in strength and modulus; however, for the latter, there appear a remarkable improvement in toughness and a simultaneous moderate increase in strength and modulus. A series of characterizations were carried out including scanning electron microscopy, wide-angle X-ray diffraction, polarized optical microscopy, differential scanning calorimetry, dynamic mechanical analysis, and Fourier transform infrared spectrometry. It is found that both blends exhibit single glass transition on DMA tan delta curves. However, contrary to that of the melt-mixed blends, the glass transition temperature (T-g) of the in-situ ones decreases with increasing PA6co6T content. It is suggested that different mixing levels are the main reasons. Moreover, the addition of PA6co6T containing linear rigid segments conducts remarkable refinement of spherulites for the blends. Significantly different changes in the crystallographic form, spherulite size, crystalline content and perfection due to the introduction of PA6co6T for the two blends are ascribed to their varied thermomechanical histories and the presence of interchange reaction only for the in-situ blends. On the basis of the characterizations of the microstructures, the different trends of changes in the mechanical properties with the addition of PA6co6T for the two fabrication methods are discussed. (C) 2007 Wiley Periodicals, Inc.

Comprehensive Investigation on the Synthesis of Polyamide 6 and Polyurethane Elastomer Blends Via in Situ Polymerization

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

Oriented distribution structure, interaction, and performance of thermoplastic polyurethane/selective hindered amine hybrids

The Structure and Dynamic Properties of Thermoplastic Polyurethane Elastomer/Hindered Phenol Hybrids

Simultaneous Interpenetrating Polymer Networks of Polyurethane from Pentaerythritol–Modified Castor Oil and Polystyrene: Structure–Property Relationships

The Preparation of Monomer Casting Polyamide 6/Thermotropic Liquid Crystalline Polymer Composite Materials with Satisfactory Miscibility

Morphology and properties of high molecular weight polyisobutylene and thermoplastic polyurethane elastomer

Preparation of Poly(Phenylene Oxide)/Polyamide-6 Nanocomposites with High Tensile Strength and Excellent Impact Performance

Improvement of Mechanical Property for PLA/TPU Blend by Adding PLA-TPU Copolymers Prepared via In Situ Ring-Opening Polymerization

Structure, Morphology and Properties of a Novel Molecular Composite by In‐Situ Blending of Anionic Polyamide 6 with a Polyamide Copolymer Containing Rigid Segments

Morphology and Mechanical Properties of Blends of Thermoplastic Polyurethane and Polyolefins

Influence of Preparation Methods on the Structures and Properties for the Blends Between Polyamide 6co6t and Polyamide 6: Melt‐mixing and In‐situ Blending

Reactive Compatibilization of Polyamide 6/Olefin Block Copolymer Blends: Phase Morphology, Rheological Behavior, Thermal Behavior, and Mechanical Properties

Functionalization of Polypropylene and Compatibilization of Polypropylene/Nylon 6 Blends with Copolymers Containing Alpha-Methyl Styrene Units

Study on Chain Extension Blending Modification and Foaming Behavior of Thermoplastic Polyamide Elastomer

Approach to Fabricating Thermoplastic Polyurethane Blends and Foams with Tunable Properties by Twin‐Screw Extrusion and Microcellular Injection Molding

Compatibilization Effect of MMA-co-GMA Copolymers on the Properties of Polyamide 6/poly(vinylidene Fluoride) Blends

FUNCTIONALIZATION OF POLYPROPYLENE AND COMPATIBILIZATION OF POLYPROPYLENE/NYLON 6 BLENDS WITH Α-Methyl STYRENE/STYRENE/MALEIC ANHYDRIDE TERNARY COPOLYMER

Synthesis of novel polycarbonate‐based thermoplastic polyurethane elastomers compatibilizers with octadecyl side chains and their application in PC / PP blends

Study of Nanocomposites Prepared by Melt Blending Tpu and Montmorillonite