Abstract:The SC200 superconducting cyclotron for hadron therapy is under development by collaboration of ASIPP (Hefei, China) and JINR (Dubna, Russia). The accelerator will provide 200 MeV proton beam with maximum current of 1μA in 2017-2018. The cyclotron is very compact and light, the estimate total weight is about 35 tons and extraction radius is 60 cm. We have performed simulations of all systems of the SC200 cyclotron and specified the main parameters of the accelerator. Average magnetic field of the cyclotron is up to 3.5 T and the particle revolution frequency is about 45 MHz, these parameters increases the requirements for accuracy of the beam dynamics studies. We have designed and performed beam tracking starting from the ion source. Codes and methods used for the beam tracking are presented. BEAM DYNAMICS SIMULATIONS Presently, research and development studies of every accelerator starts with computer simulations. For the SC200 cyclotron we build computer models of the major systems, which effect the beam dynamics in the accelerator. Modern computers performance allows to perform accurate particle tracking from the ion source to the extraction point with high accuracy. Also, one of the most important study is the conventional analysis of betatron oscillations. We use both methods to design the SC200 cyclotron. In order to perform those studies we use various commercial codes such as ANSYS, CST, OPERA-TOSCA and COMSOL Multiphysics to simulate the magnetic field and RF electro-magnetic field. CENTRAL REGION STUDIES Internal PIG proton source will be used in our cyclotron, so our simulations start from the inside of the source. We have built a 3D model of the source and the central region, shown in Fig. 1. The geometry of the ion source used in the simulations is similar to those commonly used in accelerator physics. It consists of a “chimney” with a hole for the protons to come out. In order to increase the efficiency of the extraction of the protons from the source the first accelerating gap between the tip of the RF dee and the source should be kept as small as possible. However, sparking must be prevented, so we need to provide safe distance in both vertical and horizontal directions. The compact size of the accelerator is the major challenge in the design of the central region. Ideally, we would use accelerating voltage of about 100kV in the central region, as on the first turn the beam should get enough energy to bypass the chimney of the source. Figure 1: 3D model of the source and central region. However, such voltage would require at least 1.5cm vertical gap between the RF dee and the “plug” of the magnet and in this case it would be difficult to achieve the area of decreasing magnetic field (also known as “bump”) for the initial turns, which is required to help with the focusing of the beam. Central region of the magnet and the average magnetic field are shown in Fig. 2 and Fig. 3. Figure 2: 3D model of the magnet, central “plug” (steel cylinder connecting the sectors) is 6cm in diameter. The cylinder, connecting the sectors in the central region has to be as small as possible in diameter, so the magnetic field variation can start at the smaller radius to help with the focusing, but also has to be big enough and close enough to the median plane to provide the area with TUPMR018 Proceedings of IPAC2016, Busan, Korea ISBN 978-3-95450-147-2 1268 C op yr ig ht © 20 16 C C -B Y3. 0 an d by th e re sp ec tiv e au th or s 04 Hadron Accelerators

Numerical Orbit Tracking in 3D Through the Injector Cyclotron for Heavy Ions at Ithemba LABS

High Intensity Proton Beam Transportation Through Fringe Field of 70 MeV Compact Cyclotron to Beam Line Targets

Numerical Investigation for High Intensity H− Beam Injection to a 100 MeV Compact Cyclotron

Beam Tracking Simulation for SC200 Superconducting Cyclotron

Towards quantitative predictions of high power cyclotrons

DECY-13 cyclotron equilibrium orbit verification using CYCLONE

Investigation and quantitative simulation of beam physics for 230 MeV SC cyclotron under construction at CIAE

Interplay of Space Charge and Intra-Beam Scattering in the LHC ion injector chain

Space charge simulation on high intensity cyclotrons: code development and applications

Application and Development of a Method to Shim the Isochronous Field in Small Cyclotrons

Three-dimensional modelling of processes in Electron Cyclotron Resonance Ion Source

A study of multipacting effects in large cyclotron cavities by means of fully 3-dimensional simulations*

A Two-Dimension Beam Dynamics Simulation Code Base On Pic Method

Challenges in simulating MW beams in cyclotrons

Three-dimensional simulations of ion dynamics in the plasma of an Electron Cyclotron Resonance Ion Source

Computer Modeling of Magnet for SC200 Superconducting Cyclotron

A Particle-in-cell Mode Beam Dynamics Simulation of Medium Energy Beam Transport for the SSC-Linac

3D Particle-in-cell Simulations of Electron Magnetic Confinement in Electron Cyclotron Resonance Ion Sources.

Ion Trajectory Simulation for Electrode Configurations with Arbitrary Geometries

High Performance Computation on Beam Dynamics Problems in High Intensity Compact Cyclotrons

Beam Formation Studies on the CERN IS03b H Source