Abstract:Borehole Imaging technology is often key for reservoir characterization and becomes more relevant when images are acquired while drilling to capture reservoir geology and petrophysical property distributions around the borehole. Logging While Drilling (LWD) high-resolution electrical/acoustics images of the borehole can resolve formation layers and heterogeneity down to 5mm (0.2in) scale and can detect response from far smaller features. This allows both, improved operational efficiency and better-informed drilling as well as shortening of the geological interpretation turn-around time from wireline logging time (days after drilling) to semi-real time (drilling time or hours after drilling). LWD high resolution images often suffer from the lack of direct downhole velocity measurements against the sensors. Depth tracking is on surface, referenced to the surface block movement. The imaging sensor acquiring data can be thousands of feet away from this surface reference. Imaging sensors on the bottom-hole assembly (BHA) are located not too far away from the drill bit. They are also subject to complex drilling-time motion such as tool whirling, stick and slip, vibration, mode coupling etc. This can make the downhole sensor movement dis-synchronized with the surface pipe depth increment. The Time-Depth conversion may accordingly get dis-synchronized to generate LWD depth image with missing features and distorted feature-integrity in depth. In severe conditions distorted image impacts real time image feature interpretation and leads to increased interpretation uncertainties. In this paper we investigate two main dis-synchronization problems using synthetic data: heave effect and BHA stick and slip effect. Pseudo velocity is computed from the surface measurement due to the lack of downhole sensor velocity direct measurement. In order to minimize heave effect, an advanced band-pass filter is proposed. The filter order is chosen in consistency with the sensor’s pseudo velocity behavior. Other properties of this advanced filter are also presented. In order to minimize the BHA stick and slip effect, pseudo velocity is analyzed as a delayed and minimized representative of the downhole sensor movement. A windowed-thresholding method is proposed to restore the compressed and stretched image features. Dip error analysis is performed by picking bed and fracture surface on the synthetic image data, before and after image distortion correction. The analysis results show a non-negligible effect on the accuracy of the true dip computed if the distortions are left un-corrected. Even in favorable logging conditions, the apparent dip error can contribute up to 50% of the total error. In this case, the image post-processing method proposed in this paper can not only improve the image quality but also reduce image interpretation uncertainties.

Inverting the Rock Mass P-wave Velocity Field Ahead of Deep Buried Tunnel Face While Borehole Drilling

Surface-wave geological exploration method based on Tunnel Boring Machine (TBM) drilling noise

An Inverted Heterogeneous Velocity Model for Microseismic Source Location in Deep Buried Tunnels

Simulation of the Borehole Quasistatic Electric Field Excited by the Acoustic Wave During Logging While Drilling Due to Electrokinetic Effect

Detection of karst voids at pile foundation by full-waveform inversion of single borehole sonic data

Application of Long-Range Cross-Hole Acoustic Wave Detection Technology in Geotechnical Engineering Detection: Case Studies of Tunnel-Surrounding Rock, Foundation and Subgrade

Multi-borehole three-dimensional induced polarization tomography method for tunnel water hazards ahead prospecting

High-resoultion Shallow Anomaly Characterization Using Cross-Hole P- and S-wave Tomography

Full-decay induced polarization multi-parameter tomography method for tunnel water inrush ahead prospecting: A case study

A Borehole Multifrequency Acoustic Wave System for Karst Detection Near Piles

Experimental evaluation of rock disintegration detection in drilling by a new acoustic sensor method

3-D Tunnel Space Elastic Reverse Time Migration in Cylindrical Coordinates Using Reconstructed Time-Domain Wavefields

A high resolution detection approach combining probe drilling and horizontal cross-hole resistivity tomography to interpret water conducting channels ahead of the tunnel: A case study in Yunnan, China

Digital monitoring of rotary-percussive drilling with down-the-hole hammer for profiling weathered granitic ground

A NEW PSEUDO-VELOCITY-BASED METHOD TO MITIGATE LWD IMAGE INTERPRETATION RISKS

Forward prediction for tunnel geology and classification of surrounding rock based on seismic wave velocity layered tomography

Prestack reverse time imaging in tunnels based on the decoupled nonconversion elastic-wave equation

Near‐surface Tunnel Detection Using Diffracted P‐waves: A Feasibility Study

Real-time tunneling risk forecasting using vibrations from the working TBM

Adaptive Global Optimization of Real-Time Boundary Detection From the LWD Azimuthal Electromagnetic Measurements in Layered TI Formation With Arbitrarily Deviated Borehole

Research on multi-frequency ultrasonic scanning detecting technology of cavity in the test borehole