Abstract:Objective: To investigate the influence of light and heavy bite force on the mandibular movement trajectories, and the influence of bite force on virtual occlusal pre-adjustment of digital full crown. Methods: From October 2021 to March 2022, 10 postgraduate volunteers (3 males and 7 females, aged 22-26 years) were recruited from Peking University School and Hospital of Stomatology. Maxillary and mandibular digital models of the participants were obtained by intraoral scanning. Jaw relations were digitally transferred under heavy bite force and mandibular movement trajectories under light and heavy bite force were recorded by jaw motion analyser. Three mandibular markers were chosen, namely the mesial proximal contact point of the central incisor (incisal point) and the mesial buccal cusp tips of the bilateral first molars. The three-dimensional displacements of the markers under two kinds of bite force in the intercuspal position (ICP), the sagittal projection of the three-dimensional displacements in the protrusive edge-to-edge position, and the coronal projection of the three-dimensional displacements in the lateral edge-to-edge position of upper and lower posterior teeth were measured. Single-sample t-test was used to compare the three-dimensional displacements and the corresponding sagittal projection and coronal projection with 0, respectively. The left maxillary central incisor and left mandibular first molar were virtually prepared by the reverse engineering software. Then dental design software was used to design digital full crown using the copy method. The mandibular movement trajectories under light and heavy bite force were separately used to guide virtual occlusal pre-adjustment. The three-dimensional deviations (mean deviations and root mean square) between the lingual surface of the left maxillary central incisor or the occlusal surface of the left mandibular first molar and that of the natural tooth before preparation were calculated (light bite force group and heavy bite force group), and the differences between the two groups were compared by the paired t-test. Results: Under the two kinds of bite force, the three-dimensional displacements of the markers in the ICP were (0.217±0.135), (0.210±0.133) and (0.237±0.101) mm, respectively; the sagittal projection of the three-dimensional displacements of the markers in the protrusive edge-to-edge position were (0.204±0.133), (0.288±0.148) and (0.292±0.136) mm, respectively; the coronal projection of the three-dimensional displacements of the mesial buccal cusp tips of the bilateral first molars in the lateral edge-to-edge position were (0.254±0.140) and (0.295±0.190) mm, respectively. The differences between the above displacements and 0 were statistically significant (P<0.05). The results of occlusal pre-adjustment showed that the mean deviations of the lingual surface of the left maxillary central incisor in the light and heavy bite force groups were (0.215±0.036) and (0.195±0.041) mm (t=3.95, P=0.004), respectively. The mean deviations of the occlusal surface of the left mandibular first molar were (0.144±0.084) and (0.100±0.096) mm (t=0.84, P=0.036), respectively. Conclusions: Both the light and heavy bite force have an influence on the mandibular movement trajectories. Virtual occlusal pre-adjustment of prostheses with mandibular movement trajectories under heavy bite force can obtain morphology of lingual or occlusal surfaces closer to the natural teeth before preparation.

Occlusal Contact Characteristics of Molar Teeth with Food Impaction: Insights from a New Digital Technique

Quantitative evaluation of the proximal contact area gap change characterization under intercuspal occlusion by intraoral 3D scanning: Food impaction with tight proximal contact

Construction of a Novel Digital Method for Quantitative Analysis of Occlusal Contact and Force

Quantification Of Clinical Parameters In Patients With Vertical Food Impaction Treated By Occlusal Adjustment: Cone-Beam Computed Tomography Analysis

[Etiology and Clinical Technology of the Food Impaction with Tight Proximal Contacts].

Finite Element Analysis on Tooth and Periodontal Stress under Simulated Occlusal Loads

[Patterns of Occlusal Contacts During Unilateral Mastication in Asymptomatic Subjects].

Photoelastic Study of the Effects of Occlusal Surface Morphology on Tooth Apical Stress from Vertical Bite Forces.

Occlusion Stress Analysis of Mandibular First Molar

[A Three-Dimensional Finite Element Analysis on the Effect of Seven Different Occlusions on TMJ].

[Study on mandibular movement trajectory and virtual occlusal pre-adjustment under light and heavy bite force].

Vertical contact tightness of occlusion comparison between orofacial myalgia patients and asymptomatic controls: a pilot study

An innovative evaluation method for clinical comparative analysis of occlusal contact regions obtained via intraoral scanning and conventional impression procedures: a clinical trial

A Three-Dimensional Analysis of Measuring Occlusal Contacts of Complete Denture

Effect of occlusal contact on TMJ loading during occlusion: An in silico study

Effect of Different Occlusal Forces on the Accuracy of Interocclusal Records of Loose Teeth

Three-dimensional Finite Element Analysis of Influence of Occlusal Surface Height on Stress Distribution Around Posterior Implant-Supported Single Crown

Biomechanical Evaluation of the Mandibular First Molar After Simulated Occlusal Wear Using 3D Finite Element Analysis

Stable Tooth Contacts in Intercuspal Occlusion Makes for Utilities of the Jaw Elevators During Maximal Voluntary Clenching

Quantitative parameters of digital occlusal analysis in dental implant supported restorative reconstruction recent 5 years: a systematic review

Association Between Contact from an Overerupted Third Molar and Bilaterally Redistributed Electromyographic Activity of the Jaw Closing Muscles