Abstract:Objective: To investigate the influence of light and heavy bite force on the mandibular movement trajectories, and the influence of bite force on virtual occlusal pre-adjustment of digital full crown. Methods: From October 2021 to March 2022, 10 postgraduate volunteers (3 males and 7 females, aged 22-26 years) were recruited from Peking University School and Hospital of Stomatology. Maxillary and mandibular digital models of the participants were obtained by intraoral scanning. Jaw relations were digitally transferred under heavy bite force and mandibular movement trajectories under light and heavy bite force were recorded by jaw motion analyser. Three mandibular markers were chosen, namely the mesial proximal contact point of the central incisor (incisal point) and the mesial buccal cusp tips of the bilateral first molars. The three-dimensional displacements of the markers under two kinds of bite force in the intercuspal position (ICP), the sagittal projection of the three-dimensional displacements in the protrusive edge-to-edge position, and the coronal projection of the three-dimensional displacements in the lateral edge-to-edge position of upper and lower posterior teeth were measured. Single-sample t-test was used to compare the three-dimensional displacements and the corresponding sagittal projection and coronal projection with 0, respectively. The left maxillary central incisor and left mandibular first molar were virtually prepared by the reverse engineering software. Then dental design software was used to design digital full crown using the copy method. The mandibular movement trajectories under light and heavy bite force were separately used to guide virtual occlusal pre-adjustment. The three-dimensional deviations (mean deviations and root mean square) between the lingual surface of the left maxillary central incisor or the occlusal surface of the left mandibular first molar and that of the natural tooth before preparation were calculated (light bite force group and heavy bite force group), and the differences between the two groups were compared by the paired t-test. Results: Under the two kinds of bite force, the three-dimensional displacements of the markers in the ICP were (0.217±0.135), (0.210±0.133) and (0.237±0.101) mm, respectively; the sagittal projection of the three-dimensional displacements of the markers in the protrusive edge-to-edge position were (0.204±0.133), (0.288±0.148) and (0.292±0.136) mm, respectively; the coronal projection of the three-dimensional displacements of the mesial buccal cusp tips of the bilateral first molars in the lateral edge-to-edge position were (0.254±0.140) and (0.295±0.190) mm, respectively. The differences between the above displacements and 0 were statistically significant (P<0.05). The results of occlusal pre-adjustment showed that the mean deviations of the lingual surface of the left maxillary central incisor in the light and heavy bite force groups were (0.215±0.036) and (0.195±0.041) mm (t=3.95, P=0.004), respectively. The mean deviations of the occlusal surface of the left mandibular first molar were (0.144±0.084) and (0.100±0.096) mm (t=0.84, P=0.036), respectively. Conclusions: Both the light and heavy bite force have an influence on the mandibular movement trajectories. Virtual occlusal pre-adjustment of prostheses with mandibular movement trajectories under heavy bite force can obtain morphology of lingual or occlusal surfaces closer to the natural teeth before preparation.

Quantification Of Clinical Parameters In Patients With Vertical Food Impaction Treated By Occlusal Adjustment: Cone-Beam Computed Tomography Analysis

The effect of occlusal interference on the restoration of the idiopathic cervical lesions

Research of changes of symptoms and bone structure imaging of temporomandibular joint after treatment of occlusal recon struction

Relationship between vertical dimension and bite force as well as electromyography in edentulous people

X-ray cephalometric analysis of the occlusal rehabilitation treatment for the patients with occlusal vertical dimension increasement

Quantitative evaluation of the proximal contact area gap change characterization under intercuspal occlusion by intraoral 3D scanning: Food impaction with tight proximal contact

[Three-Dimensional Analysis of the Early Correction of Anterior Crossbite Using Eruption Guidance Appliance].

A cone-beam computed tomography analysis of angulation and inclination of whole tooth and clinical crown in adults with normal occlusion

Influence of Impacted Maxillary Central Incisor on Craniofacial Structure and Its Orthodontic Treatment

[Evaluation of the Orthodontic Treatment Outcome in Patients with Impacted Maxillary Central Incisor in the Mixed Dentition].

[Improvement of the mastication function of orthodontics combined with restoration in the treatment of deep overbite with severe lower anterior teeth attrition]

[Investigation of Posterior Teeth Displacement under Normal Bite Force by an Intraoral Scanner].

Evaluation of anterior teeth crown-root morphology and alveolar bone structure in patients with closed deep overbite using cone beam computed tomography

[Adoption of the Condyle Position of Patients with Extensive Tooth Wear During Occlusal Rehabilitation].

An innovative evaluation method for clinical comparative analysis of occlusal contact regions obtained via intraoral scanning and conventional impression procedures: a clinical trial

Vertical Changes in the Hard Tissues after Space Closure by Miniscrew Sliding Mechanics: a Three-Dimensional Modality Analysis.

[Study on mandibular movement trajectory and virtual occlusal pre-adjustment under light and heavy bite force].

Combined Orthodontic-Periodontal Treatment in Periodontal Patients with Anteriorly Displaced Incisors.

[Cephalometric evaluation of the effects of pendulum appliance on various vertical growth patterns]

[Clinical study of the effect of combined orthodontic and restoration treatment for introverted deep overbite patients with severe wear]

Three-dimensional Measurement of Periodontal Support During Surgical Orthodontic Treatment of High-Angle Skeletal Class III Malocclusion: A Retrospective Study.