Abstract:Heterostructured materials address the inherent trade-off between strength and toughness, allowing alloys to enhance toughness while simultaneously increasing strength. However, the regulation of heterostructures and the preparation of large-volume specimens remain significant challenges. The aim of this study was to prepare gradient-structured 5083 aluminum alloys using the constrained deformation method and to investigate its effects on the comprehensive mechanical properties. Additionally, the strengthening mechanisms of the constrained deformation specimens were elucidated. The microstructure was characterized using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The mechanical properties were assessed through microhardness and uniaxial tensile tests. The findings indicate that the constrained deformation treated 5083 aluminum alloy exhibits a substantial improvement in comprehensive mechanical performance. In comparison to the as-received specimens, the yield strength of the constrained deformation specimens (CDS) significantly increases with the increases volume fraction of the DL. Nonetheless, these specimens maintain an average elongation at break ranging from 12.3% to 14.3%. The enhanced properties of the gradient-structured 5083 aluminum alloy are primarily attributed to the high density of geometrically necessary dislocations (GNDs) and the elevated proportion of low-angle grain boundaries (LAGBs). Specifically, the increase in dislocation density contributes significantly to the alloy's strength, while additional heterogeneous deformation-induced (HDI) hardening, along with a high proportion of LAGBs, preserves the alloy's excellent toughness. This study provides novel insights and methodologies for the optimal design and large-scale application of heterostructures in aluminum alloys.

Tailoring High-Entropy Oxides to Ameliorate Interfacial Mismatch of Aluminum-Matrix Composites Towards Superior Strength-Ductility Balance

Break through the strength-ductility trade-off dilemma in aluminum matrix composites via precipitation-assisted interface tailoring

Enhancing the Strength of AlCrFeNi HEAs Via Tailoring Aluminum Content and Optimal Aging Treatment

Tailoring heterogeneities in high-entropy alloys to promote strength–ductility synergy

Tailoring the heterophase interfacial structures to improve both strength and ductility of Al-Li alloys by fine tuning major solute Mg

The synergistic effects of heterogeneous structures enhance the strength-ductility of Al-Cu composites

Achieving High Strength and High Ductility in a High-Entropy Alloy by a Combination of a Heterogeneous Grain Structure and Oxide-Dispersion Strengthening

Strength-ductility materials by engineering coherent interface at incoherent precipitates

Theory-guided design of high-entropy alloys with enhanced strength-ductility synergy

Design of a Thermally Stable Heat-Resistant (Al2O3+Al3Ti)/Al Composite with Excellent High-Temperature Mechanical Properties: Multimechanism Synergistic Strengthening Strategy

A Novel Method for the Preparation of Heterostructures 5083 Aluminum Alloys to Enhancing Comprehensive Mechanical Properties

Back stress dynamic balancing strategy enabled strength-ductility synergy in heterostructured Al-SiC composites

Tailoring Hierarchical Microstructures and Nanoprecipitates in Additive-Manufactured Al-Zn-Mg-Cu-Nb Alloys for Simultaneously Enhancing Strength and Ductility

Trimodal Grain Structured Aluminum Matrix Composites Regulated by Transitional Hetero-Domains

Processing Heterogeneously Structured Oxide-Dispersion-strengthened Fe-10Cr-6.1Al-0.3Zr-0.1Y Alloy for Simultaneously Enhanced Strength and Ductility

Enhanced strength and ductility synergy of a CoCrFeMnNi high entropy alloy with a hierarchical structure via severe distortion

In-situ solid-state deformation-driven rapid reaction towards higher strength-ductility Al-CuO composites

Manipulating the ordered oxygen complexes to achieve high strength and ductility in medium-entropy alloys

Enhancement of Strength-Ductility Trade-off in a High-Entropy Alloy Through a Heterogeneous Structure

Overcoming strength-toughness trade-off in a eutectic high entropy alloy by optimizing chemical and microstructural heterogeneities

Simultaneous enhancement of strength and ductility by combining heterogeneous microstructure and nanoprecipitates