Abstract:Surface-mounted permanent-magnet (PM) motors are widely used in motion control systems because of their high peak torque-to-inertia ratio. These motors exhibit high magnetic saturation to produce high peak torque. A precise finite-element model (FEM) is needed to optimize these motors. It requires high computation power, especially for multi-objective optimizations. On the contrary, subdomain models require low computing power but are inaccurate when magnetic saturation occurs. To solve this problem, we use a subdomain-assisted FEM optimization method (SAFEMOM) that combines subdomain models for preoptimization and FEM for refined optimization. We provide the quantitative measurement methods to compare SAFEMOM with FEM-only optimization. If the constraints in the magnetic fluxes in the subdomain part of SAFEMOM are based on the actual saturation value of the materials, then the advantage of SAFEMOM is not significant. The machines in this study use non-linear material with a knee point at 1.3 T and hence show heavy magnetic saturation above 1.5 T. In that case, contrary to what could be intuitively thought, we need to increase the magnetic flux density limit to 2.6 T - 3.0 T in SAFEMOM to have a significant advantage. SAFEMOM reduces about 80% of computing time to obtain a slightly better convergence than the one using FEM only. Also, if limited computing resource is allowed, SAFEMOM gives an error reduced by a factor of nearly eight compared to the optimization error using FEM only. Those results are validated on a family of surface-mounted permanent-magnet machines with a wide range of design parameters.

An Accurate Multi-objective Optimization Strategy for Surface-Mounted Permanent-Magnet Machines Based on Nonlinear Finite-Permeability Subdomain Model

FEA-Based Mathematical Modeling and Simulation for IPMSM Drive with Consideration of Saturation and Cross-Coupling Influence

A Nonlinear 3-D Hybrid Model for Surface-Mounted Permanent Magnet Machines Considering End Effect

A Multi-Objective Finite-Element Method Optimization That Reduces Computation Resources Through Subdomain Model Assistance, for Surface-Mounted Permanent-Magnet Machines Used in Motion Systems

Unbalanced Magnetic Force Calculation Based on Subdomain and Magnetic Circuit Hybrid Model in SPM Machines

Analytical Investigation and Heuristic Optimization of Surface Mounted Permanent Magnet Machines With Hybrid Magnetic Structure

Nonlinear Analytical Model-Embedded Optimal Design for ER-PMSM

Fast Magnetic Field Prediction Based on Hybrid Subdomain Method and Multiobjective Optimization Design for Interior Permanent Magnet Synchronous Machines

Multi-Objective Optimal Design of High-Speed Surface-Mounted Permanent Magnet Synchronous Motor for Magnetically Levitated Flywheel Energy Storage System

On-Load Field Prediction of Surface-Mounted PM Machines Considering Nonlinearity Based on Hybrid Field Model

Magnetic Field Prediction In Surface-Mounted Pm Machines With Parallel Slot Based On A Nonlinear Subdomain And Magnetic Circuit Hybrid Model

A computationally efficient surrogate model based robust optimization for permanent magnet synchronous machines

Comparative Analysis and Design Optimization of Ferrite-Based Surface PM Vernier Machines

Analysis and Research on No-Load Air Gap Magnetic Field and System Multi-Objective Optimization of Interior PM Motor

Investigation of Analytical Models for Surface-Mounted Permanent Magnet Motor Using Voltage Source Inverter

Optimization of a Consequent-Pole PMSM with a Sobol Sequence Based Multi-Objective Hybrid Optimization Algorithm

Multiobjective Particle Swarm Optimization Design of Permanent Magnet Machine for Torque Density Improvement and Torque Ripple Suppression

Comparison of Two Finite-Permeability Subdomain Models for Surface-Mounted Permanent-Magnet Machines.

Multiobjective Optimization of the PMSM With the Same Number of Poles and Slots Considering Dynamic Response and Torque Performance

A Hybrid Model of Permanent-Magnet Machines Combining Fourier Analytical Model with Finite Element Method, Taking Magnetic Saturation into Account

Surrogate-Assisted Optimization of a Five-Phase SPM Machine With Quasi-Trapezoidal PMs