Abstract:This study utilizes a lab-developed pneumatic-extrusion condensing 3D food printer to prepare astragalus–starch mixed gels by blending different ratios of astragalus polysaccharide and wheat starch and applies these gels to 3D printing experiments. The aim of this paper is to investigate the impacts of mixed-gel concentrations on printing outcomes in order to identify the optimal blending ratio. Under this rationale, the effects of printing layer height and nozzle diameter on print quality were studied. Single-factor analysis and response surface methodology were employed to optimize the experiments and determine the optimal printing process parameters for the astragalus–starch mixed gels. The results indicate that an increase in astragalus polysaccharide content leads to a decrease in the sedimentation rate of the mixed gels and a tendency towards a more fluid consistency. After storage of samples in a sealed space for equal durations, it was found that an increase in astragalus polysaccharide content enhances the textural properties of the mixed gels, with optimal printing effects achieved at a 2% polysaccharide content. The optimal print quality is achieved when the ratio of nozzle diameter to layer height is between 0.5 and 0.55. The influence order of printing process parameters on the overall completion rate of the samples is nozzle diameter > printing speed > fill rate. The predicted optimal printing parameters are a nozzle diameter of 0.6 mm, a printing speed of 767 mm/min, and a fill rate of 83%, with a predicted overall completion rate of the printed samples at 99.45%. Experimental validation revealed an actual overall completion rate of the printed samples at 99.52%, slightly higher than the predicted value. This discrepancy was attributed to the precision of the measurement methods and the variability in the printing process. The study demonstrates that the addition of astragalus polysaccharide significantly improves the 3D printing molding effect of wheat starch, and the printing parameter settings obtained by response surface optimization effectively enhance printing accuracy. This research provides experimental evidence and parameter optimization references for the application of non-starch polysaccharides in starch-based 3D food printing.

Effect of Κ-Carrageenan on Physicochemical and 3D Printing Properties of Walnut Protein-Stabilized Emulsion Gel

Impact of κ-Carrageenan on the Cold-Set Pea Protein Isolate Emulsion-Filled Gels: Mechanical Property, Microstructure, and In Vitro Digestive Behavior

Effects of Κ-Carrageenan Gum on 3D Printability and Rheological Properties of Pork Pastes.

Rheology and 3D printing characteristics of heat-inducible pea protein-carrageenan-glycyrrhizic acid emulsions as edible inks

The synergistic effect of κ-carrageenan and l-lysine on the 3D printability of yellow flesh peach gels: The importance of material elasticity in the printing process

Improvement of Extrudability and Self-Support of Emulsion-Filled Starch Gel for 3D Printing: Increasing Oil Content

Three-Dimensional Printing Properties of Polysaccharide Hydrocolloids-Unrinsed Sturgeon Surimi Complex Hydrogels

Modified Starch-Based Emulsion-Filled Gels for 3D Printing: Preparation, Characterization, and Printability

Effect of Xanthan Gum on Physicochemical Properties and 3D Printability of Emulsion-Filled Starch Gels

Development of 3D printed k-carrageenan-based gummy candies modified by fenugreek gum: Correlating 3D printing performance with sol-gel transition

Effect of Starch Molecular Structure on Precision and Texture Properties of 3D Printed Products

Effect of Carrageenan on Stability and 3D Printing Performance of High Internal Phase Pickering Emulsion Stabilized by Soy Protein Isolate Aggregates under Neutral Condition

3D Printing Properties of Heat-Induced Sodium Alginate-Whey Protein Isolate Edible Gel

Effects of Co-Assembly of Gliadin and Carboxymethyl Cellulose on the High Internal Phase Pickering Emulsions: Rheology Properties, 3D Printing Performance and Oil-Soluble Nutrient Delivery

Effect of Induction Mode on 3D Printing Characteristics of Whey Protein Isolate Emulsion Gel

Protein-stabilized Pickering emulsion interacting with inulin, xanthan gum and chitosan: Rheological behavior and 3D printing

Exploring gelation properties and structural features on 3D printability of compound proteins emulsion gels: Emphasizing pH-regulated non-covalent interactions with xanthan gum

Effects of wheat protein on hot-extrusion 3D-printing performance and the release behaviours of caffeic acid-loaded wheat starch

Effect of Gums on the Multi-Scale Characteristics and 3D Printing Performance of Potato Starch Gel

Preparation of Pickering emulsion gel stabilized by tea residue protein/xanthan gum particles and its application in 3D printing

An Optimization Study of 3D Printing Technology Utilizing a Hybrid Gel System Based on Astragalus Polysaccharide and Wheat Starch