Abstract:This study utilizes a lab-developed pneumatic-extrusion condensing 3D food printer to prepare astragalus–starch mixed gels by blending different ratios of astragalus polysaccharide and wheat starch and applies these gels to 3D printing experiments. The aim of this paper is to investigate the impacts of mixed-gel concentrations on printing outcomes in order to identify the optimal blending ratio. Under this rationale, the effects of printing layer height and nozzle diameter on print quality were studied. Single-factor analysis and response surface methodology were employed to optimize the experiments and determine the optimal printing process parameters for the astragalus–starch mixed gels. The results indicate that an increase in astragalus polysaccharide content leads to a decrease in the sedimentation rate of the mixed gels and a tendency towards a more fluid consistency. After storage of samples in a sealed space for equal durations, it was found that an increase in astragalus polysaccharide content enhances the textural properties of the mixed gels, with optimal printing effects achieved at a 2% polysaccharide content. The optimal print quality is achieved when the ratio of nozzle diameter to layer height is between 0.5 and 0.55. The influence order of printing process parameters on the overall completion rate of the samples is nozzle diameter > printing speed > fill rate. The predicted optimal printing parameters are a nozzle diameter of 0.6 mm, a printing speed of 767 mm/min, and a fill rate of 83%, with a predicted overall completion rate of the printed samples at 99.45%. Experimental validation revealed an actual overall completion rate of the printed samples at 99.52%, slightly higher than the predicted value. This discrepancy was attributed to the precision of the measurement methods and the variability in the printing process. The study demonstrates that the addition of astragalus polysaccharide significantly improves the 3D printing molding effect of wheat starch, and the printing parameter settings obtained by response surface optimization effectively enhance printing accuracy. This research provides experimental evidence and parameter optimization references for the application of non-starch polysaccharides in starch-based 3D food printing.

Effect of Gums on the Multi-Scale Characteristics and 3D Printing Performance of Potato Starch Gel

Physicochemical, Interactions, and Morphology of L-Arginine/konjac Glucomannan Gel: Effects of Modified Starches

Exploring the Mechanism of Variation in 3D Printing Accuracy of Cassava Starch Gels During Freezing Process

Effect of Starch Molecular Structure on Precision and Texture Properties of 3D Printed Products

Effects of different hydrocolloids on the water migration, rheological and 3D printing characteristics of β-carotene loaded yam starch-based hydrogel

The effects of different hydrocolloids on lotus root starch gelatinization and gels properties

Effect of the addition of mung bean, corn, and sweet potato starch on the properties of konjac gel

Investigation of the mechanism of different 3D printing performance of starch and whole flour gels from tuber crops

Effect of Xanthan Gum on Properties of Tapioca Starch Paste

Exploring gelation properties and structural features on 3D printability of compound proteins emulsion gels: Emphasizing pH-regulated non-covalent interactions with xanthan gum

Research on rice starch gel preparation and crosslink network structure-rheological property based on direct-writing 3D printing

An Optimization Study of 3D Printing Technology Utilizing a Hybrid Gel System Based on Astragalus Polysaccharide and Wheat Starch

Impact of starch amylose and amylopectin on the rheological and 3D printing properties of corn starch

Investigating the fabrication and functional properties of new composite hydrogels containing gellan/ alginate/ xanthan gum

Development of soy protein isolate emulsion gels as extrusion-based 3D food printing inks: Effect of polysaccharides incorporation

Effects of Konjac Gum on Physicochemical, Rheological, Textural Properties, and In Vitro Digestibility of Purple Potato Starch

New insight into synergistic interaction between the backbone or side chain of xanthan gum and the backbone of Gleditsia sinensis polysaccharide

Hydrophilic colloids (Konjac gum/Xanthan gum) in 3D printing of transitional food from fish paste

The Effect of Hydrocolloids on Penetration Tests and Syneresis of Binary Gum Gels and Modified Corn Starch–Gum Gels

Three-Dimensional Printing Properties of Polysaccharide Hydrocolloids-Unrinsed Sturgeon Surimi Complex Hydrogels

Effect of three polysaccharides with different charge characteristics on the properties of highland barley starch gel