Abstract:<p>In ablation-resistant silicone rubber composites, the strengths of the ceramic layers strongly affect the ablation rates of the materials, and the order of graphite carbon in the ceramic layers has an important impact on the strength of ceramic layers. In this study, a series of 4,4′-bis(3-(oxiran-2-ylmethoxy)benzyl)-1,1′-biphenyl(BER) modified silicone rubber composites were prepared to improve the order of graphite carbon in the ceramic layers of composites after ablation. The introduction of SiO<sub>2</sub> nanoparticles and carbon fibers as ablation fillers made the material ceramized and formed strong ceramic layers during the ablation process. Characterization of ablation performance shown that the 20BER composite exhibited the best ablation resistance performance: a linear ablation rate of 0.0464mm/s and a mass ablation rate of 0.0500g/s. Mechanical performance characterization shown that the 20BER sample also exhibited an excellent tensile strength of 2.013MPa and a ceramic layer strength of 13.15MPa. Raman measurement indicated that the addition of BER led to more orderly graphitic carbon structures during pyrolysis and increased the strength of ceramic layers. SEM, mercury intrusion and thermal conductivity measurements indicated that the pore volume, porosity and total pore area of ceramic layers with the BER component were all higher than the 0BER sample. The BER was proven to be an effective material which is beneficial to improve the ablation resistance and played an important role in the process of ceramization of the silicone rubber composites. These silicone rubber composites have the potential to be applied to the surface coating of aircraft.</p>

In Situ Construction of Silicon Containing Carbon Layer by Hyper Silicone-Branched Structure Endows Epoxy/Carbon Fiber Composites with High Strength and Ablation Resistance

Silicone-grafted epoxy/carbon fiber composites with superior mechanical/ablation performance

In situ construction of fiber‐supported micro‐porous char structure to enhance anti‐ablative performance of silicone rubber composites

Preparation of Ceramifiable and Ablatively Resistant Epoxy Resins by Microphase Structure Modulation of Silicones

In-situ constructing SiC frame in silicone rubber to fabricate novel flexible thermal protective polymeric materials with excellent ablation resistance

A facile in-situ strategy to fabricate lightweight carbon fiber/silicone-phenolic aerogel composites with superior toughness and ablation performance

Controlled pyrolysis of epoxy through highly silicone-branched structures to construct a compact porous char layer for ablation resistant coatings

Improved Thermal Stabilities, Ablation and Mechanical Properties for Carbon Fibers/Phenolic Resins Laminated Composites Modified by Silicon-containing Polyborazine

Improvement of Silicon and Epoxy Phase Interface by Constructing Rigid Interpenetrating Networks Based on Bismaleimide to Enhance Ablative, Mechanical and Thermal Properties

Improving high heat flux ablation resistance of silicone rubber composites by laying low-areal-density carbon fiber fabrics

A Comparison of Ablative Resistance Properties of Liquid Silicone Rubber Composites Filled with Different Fibers

Effects of Inorganic Nanofibers and High Char Yield Fillers on Char Layer Structure and Ablation Resistance of Ethylene Propylene Diene Monomer Composites

Improving the Ablation Performance of Largely Deformed Silicone Rubber-Based Composites under Coupled Mechanical-Thermal-Oxidative Conditions by Implementing Deformable Carbon Fiber Fabrics

Preparation and Ablative Behaviors of Carbon Fiber‐reinforced Polydimethylsiloxane‐co‐poly(silylene Acetylenearyleneacetylene) Composites

Ordered graphitized ceramic layer induced by liquid crystal epoxy resin in silicone rubber composites with enhanced ablation resistance performance

Construction of “Rigid-Flexible” Cocrosslinked Networks by Grafting Bismaleimide and Silicone to Prepare Tough, Heat-Resistant, and Ablation-Resistant Epoxy Composites

Preparation of Integrated Carbon Fiber Stitched Fabric Reinforced (sibcn) Ceramic/resin Double-Layered Composites for Ablation Resistance, Thermal Insulation and Compression Resistance Performance

Multiscale, Elastic, and Low-Density Carbon Fibre / Siliconoxycarbide-Phenolic Interpenetrating Aerogel Nanocomposite for Ablative Thermal Protection

Preparation and Ablation Performance of Silica Modified Phenolic/carbon Fiber Composite

Improving ablation properties of liquid silicone rubber composites by in situ construction of rich‐porous char layer

Significantly improved ablation properties under high heat flux environment based on carbon fiber reinforced Zr-doped silicone rubber