Abstract:Tiltrotor aircraft combine the vertical take-off and landing capability of a helicopter with the high cruising speed of a fixed-wing airplane. During flight, the aircraft switches between helicopter and airplane modes. Meanwhile, structural vibration and deformation are affected by changes in the aerodynamic loads, collective pitch, and rotation speed of blades. Therefore, it is crucial to consider dynamic characteristics in different modes. This paper presents a surrogate-based structural design framework of a tiltrotor blade to speed up calculations while maintaining accuracy. The shape generation method, rapid finite element method (FEM) model generation, and simplified boundary conditions are implemented to compute the blade modal frequencies, mass and inertia. A B-spline is used to construct the shape of the blade with the distribution of airfoils, twist angles, chord length, swept angles, and dihedral angles. These geometric features are realized by approximation, rotation, translation, and scaling of the control points. The spanwise distribution of the C-beam area and the width and length of the skins are selected to parameterize and establish the FEM model. The blind kriging model is applied to develop a surrogate model. The precision of this surrogate model is evaluated and compared to the kriging model and backpropagation neural network (BPNN) model based on the blade of an eight-ton-weight aircraft. A blade with a linear spanwise distribution of the C-beam area is designed using these three surrogate models trained by 13 samples. The results reveal that the error of the blind kriging model concerning the first four modal frequencies is less than 0.5% and lower than that of the other two models. A gimbal hub is modeled using a combination of a simply supported and a clamped boundary condition at the root. The two boundary conditions and two working conditions are unified into one working condition since a linear relationship is found. Moreover, the effects of the segmented linearly distributed cross-sectional area of the C-beam and the geometric parameters of the skins are investigated. The tip and root of the C-beam have the most significant influence on the low-order modal frequency. The parameters of the skins have opposite effects on the 1st and 2nd flap frequencies and the 1st torsion frequency. This framework provides a complete design process on the basis of geometric features and design parameters in the structure design, reducing the design variables. The use of the surrogate model and simplified working conditions reduce the consumption of time in the design. Conclusions about the tiltrotor blade have reference significance in the design stage.

A High-Precision T-spline Blade Modeling Method with 2D and 3D Knot Adaptive Refinement

Collisionless Tool Orientation Smoothing above Blade Stream Surface Using NURBS Envelope

Adjoint-Response Surface Method in Aerodynamic Shape Optimization of Turbomachinery Blades

Adaptive B-spline curve fitting with minimal control points using an improved sparrow search algorithm for geometric modeling of aero-engine blades

Curve Guided T-spline Skinning for Surface and Solid Generation

An adaptive sampling method for accurate measurement of aeroengine blades

Effective Re-Parameterization and GA Based Knot Structure Optimization for High Quality T-spline Surface Fitting

Adaptive Sampling Technique for Free-Form Surface of Aero-Engine Blades Based on Discrete Curvature

Investigating the Quality Inspection Process of Offshore Wind Turbine Blades Using B-spline Surfaces

Accurate Model Construction of Deformed Aero-Engine Blades for Remanufacturing

Closed T-Spline Surface Reconstruction from Medical Image Data

Sampling point planning method for aero-engine blade profile based on CMM trigger probe

Research and Application on Accurate Parametric Modeling of Aerofoil Blade

Constraints and CFD simulation-based parametric reconstruction for 2D blade profile in reverse engineering

Surrogate Model-Based Parametric Structural Design of a Composite Tiltrotor Blade

A New Curvature-Controlled Stacking-Line Method for Optimization Design of Compressor Cascade Considering Surface Smoothness

Repair of Defective 3D Blade Model Based on Deformation of Adjacent Non-Defective Cross-Sectional Curve

A Path Planning Method for Polishing Thermal Barrier Coatings on the Surface of Aero-Engine Blades Based on Point Cloud Slicing

Research of Interpolation Method in the Leading and Exhaust Edge Measurement of Turbo Blade

Stream Surface Reconstruction of Aero Engine Blade Based on Limited Measured Points.

Multi-Stage Turbomachinery Blades Optimization Design Using Adjoint Method And Thin Shear-Layer N-S Equations