Abstract:During the past years, the power conversion efficiency (PCE) of perovskite solar cells (PSCs) has increased from 3.8% to 25.7%, making them the best candidate for the next-generation photovoltaic devices. Two dominant PSC architectures have evolved, a regular n-i-p structure with mesoscopic or planar heterojunction and an inverted p-i-n planar structure. Compared to the regular n-i-p PSCs, the inverted p-i-n PSCs possess the advantages of lower synthesis temperature, no hysteretic effect and good compatibility with the tandem solar cells. For p-i-n PSCs, the hole transport layer (HTL) determines the hole transport efficiency and crystallinity of perovskite, so it plays a crucial role in the stacked devices. The conventional organic HTL of PEDOT:PSS-based PSCs can achieve satisfying PCEs, but may be able to impede the commercialization of perovskite photovoltaic devices because of their high price and acidity-induced poor stability. By comparison, the inorganic P-type NiOx with wide band gap exhibits low cost, superior chemical stability and high hole mobility without corrosion to perovskite layer. Unlike the most reported spin-coated NiOx nanoparticle films, we used sputtered NiOx as HTL for application in FA-based PSCs and achieved a PCE of 20.05%. After systematically optimizing the sputtering parameters, including power, time and argon flow rate, we obtained better crystal quality, better transparency, proper energy level, and higher hole mobility of NiOx film. Reducing the interstitial vacancies and defects in NiOx films attributes to decreased nonradiative recombination losses, which mainly cause the hole accumulation near the perovskite/NiOx interface. Finally, a champion device with open-circuit voltage (Voc) of 1.09 V, current density (Jsc) of 23.4 mA/cm 2 , fill factor (FF) of 78% and PCE of 20.05% are obtained. This work has important significance for preparation of large-area perovskite solar cell modules.

In Situ Growth of Nickel Oxide Hole-Transport Layer Through the Nickel Oleate Route for High-Performance Perovskite Solar Cells

Efficient NiOx Hole Transporting Layer Obtained by the Oxidation of Metal Nickel Film for Perovskite Solar Cells

Nickel Oxide as Efficient Hole Transport Materials for Perovskite Solar Cells

The use of nickel oxide as a hole transport material in perovskite solar cell configuration: Achieving a high performance and stable device

Printable and Homogeneous NiO x Hole Transport Layers Prepared by a Polymer‐Network Gel Method for Large‐Area and Flexible Perovskite Solar Cells

In Situ Atmospheric Deposition of Ultrasmooth Nickel Oxide for Efficient Perovskite Solar Cells

Functionalized Nickel Oxide As a Hole Transport Layer for Organic Solar Cells with Simultaneous Enhancement of Efficiency and Stability

Nitrogen‐Doped Nickel Oxide As Hole Transport Layer for High‐Efficiency Inverted Planar Perovskite Solar Cells

Development of Superior Nickel Oxide Layer for Boosted Hole‐Transport Performance in Perovskite Solar Cells

Oxidized Nickel to Prepare an Inorganic Hole Transport Layer for High-Efficiency and Stability of CH3NH3PbI3 Perovskite Solar Cells

A facile route for preparing nickel(II) oxide thin films for high-performance inverted perovskite solar cells

Triple hole transporting and passivation layers for efficient NiO<sub>X</sub>-based wide-bandgap perovskite solar cells

Room-Temperature-Sputtered Nanocrystalline Nickel Oxide as Hole Transport Layer for p–i–n Perovskite Solar Cells

Efficient Inverted Planar Perovskite Solar Cells Using Ultraviolet/Ozone‐Treated NiOx As the Hole Transport Layer

Impact of nickel oxide/perovskite interfacial contact on the crystallization and photovoltaic performance of perovskite solar cells

Synergistic Effect between NiO<i><sub>x</sub></i> and P3HT Enabling Efficient and Stable Hole Transport Pathways for Regular Perovskite Photovoltaics

Revivification of nickel oxide-perovskite interfaces via nickel nitrate to boost performance in perovskite solar cells

High-Performance Inverted Perovskite Solar Cells with Mesoporous NiO X Hole Transport Layer by Electrochemical Deposition.

Sputtered Niox Films As Hole Transport Layers for FA-Based Perovskite Solar Cell Application

Pristine inorganic nickel oxide as desirable hole transporting material for efficient quasi two-dimensional perovskite solar cells

Functionalized nickel oxide as hole transport layers for organic solar cells with simultaneous enhancement of efficiency and stability