Abstract:Catalytic combustion has been widely applied to remove the trace combustible pollutants. However, the earth-abundant and high-performance nanocatalysts are still the main research focus on promoting catalytic efficiency. Herein, the Cu and Mn mixed oxides supported on TiO2 nanoparticles with various Cu and Mn molar contents synthesized via the flame spray pyrolysis (FSP) technique are utilized in the catalytic oxidation of lean CO and CH4. Initially, the Cu–Mn/TiO2 nanocatalysts are composed of spherical structures with a diameter of about 20 nm, whose specific surface area is between 60 and 90 m2/g. The Cu element is more evenly distributed on the TiO2 surface than the Mn element, owing to the distinctly different ion radii. Both the copper and manganese cations could incorporate into the TiO2 lattice, which generates oxygen vacancies and enhances the diffusion of oxygen ions, causing the transformation of the antanse to rutile phase. When the molar content of the Cu–Mn increases to less than 30 mol %, the temperature of its reduction peak keeps decreasing due to the hydrogen spillover effect. Moreover, the catalytic performances of the Cu–Mn/TiO2 with 12 mol % loading (12CMT) are all optimal during the low-temperature and the high-temperature stages, which are superior to the FSP-made copper manganese or copper titanium oxides. This is attributed to the small crystal particles, highly dispersed active components of CuOx and MnOx, and the higher ratios of Cu1+/Cu and Mn4+–Oads Lewis acid–base pairs. In addition, the strong interaction between Cu–Mn components and rutile phase support can tremendously promote the activity of catalytic combustion. Under the simulated flue gas, the catalytic properties of 12CMT decreases in comparison with those of CO and CH4 mixed gas due to the introduction of CO2. Ultimately, the Cu–Mn/TiO2 samples exhibit the outstanding water resistance, thanks to the hydrophobization of the catalyst surface.This article has not yet been cited by other publications.

Preparation and Evaluation of FeMnTi Monolithic Catalysts for High‐Efficiency CO Oxidation

Fabrication of High-performance CeO2-MnOx/TiO2/Ti Monolithic Catalysts for Low-temperature and Stable CO Oxidation

Low-temperature and stable CO oxidation of in-situ grown monolithic Mn3O4/TiO2 catalysts

Self-assembly of a Highly Stable and Active Co3O4/H-TiO2 Bulk Heterojunction with High-Energy Interfacial Structures for Low Temperature CO Catalytic Oxidation

CuO/TiO 2 /Ti Monolithic Catalysts for Low-Temperature CO Oxidation

In-situ fabrication of Cu-Mn-O nanostructure catalysts on Ti mesh and their catalytic property optimization for low-temperature and stable CO oxidation

Fabrication of CuO/TiO 2 /Ti Monolithic Catalyst for Efficient and Stable CO Oxidation

Transition Metal (fe2o3, Co3O4 and NiO)-Promoted CuO-Based Α-Mno2 Nanowire Catalysts for Low-Temperature CO Oxidation

A Facile Route for Spraying Preparation of Pt/TiO2 Monolithic Catalysts Toward VOCs Combustion

Low-temperature and stable CO oxidation of Co3O4/TiO2 monolithic catalysts

Fabrication of Hollow-Structured FeOx-MnOx Oxidative Catalysts with Ultra-Large Surface Area

Electronic Metal-Support Interactions in Pt/FeOx Nanospheres for CO Oxidation

Synthetic Pt-Fe(OH) x catalysts by one-pot method for CO catalytic oxidation

Role of Ptnc-FeOx metal-oxide interface in enhancing the catalytic activity for CO oxidation

Preparation of MnO2 decorated Co3Fe1O powder/monolithic catalyst with improved catalytic activity for toluene oxidation

Non-noble metal single-atom catalyst with MXene support: Fe1/Ti2CO2 for CO oxidation

CuO-CeO2/Al2O3/FeCrAl monolithic catalysts prepared by in situ combustion synthesis method for preferential oxidation of carbon monoxide

One-Step Synthesis of Nanostructured Cu–Mn/TiO 2 via Flame Spray Pyrolysis: Application to Catalytic Combustion of CO and CH 4

Tuning the Structure of Bifunctional Pt/SmMn2O5 Interfaces for Promoted Low-Temperature CO Oxidation Activity

Revealing the intrinsic nature of Cu- and Ce-doped Mn3O4 catalysts with positive and negative effects on CO oxidation using operando DRIFTS-MS

Electronic metal-support interactions in Pt/FeO<i><sub>x</sub></i> nanospheres for CO oxidation