Abstract:Manufacturing CuCrZr alloy parts with high strength and high surface quality by selective laser melting (SLM) is a challenging task. This study investigates the microstructure, mechanical properties and machinability of SLM processed and heat-treated CuCrZr alloy through tensile test, compression test and ultra-precision machining. The microstructure analysis shows that the grain morphology and orientation are highly related to the laser track and building direction. Grain epitaxial growth is found on both horizontal (XY) and vertical (XZ) planes, which bends at the boundary of the molten track/pool. After heat treatment, molten track boundaries disappear and the slender and bent grains on the XY plane are replaced by polygonal square grains, but the large epitaxial grains on the XZ plane still remained. X-ray diffraction results indicate that the as-built sample contains α-Cu, Cr and CuxZry phases and building direction has an influence on the crystallographic orientation distribution. As-built (AB) CuCrZr alloy shows a comparable yield strength (218.0 MPa) with solution + ageing-treated (SAT) (231.3 MPa), which is much higher than that of the solution-treated (ST) counterpart (131.0 MPa). Although the ultimate tensile strength of the AB sample is lower than that of the SAT sample, its elongation at break (46.5%) is much higher than the latter (19.1%). The compressive strength of the AB sample is slightly lower than the SAT sample but higher than the ST sample. At low cutting speed, the ST sample shows a higher cutting force. High cutting speed will lead to the increase of cutting force of the AB and SAT samples but has a much lower effect on the ST sample. The XZ plane of the AB sample shows better machined surface quality. SAT sample has the highest material recovery during cutting and its chip will change from spiral to arc shape with the increase of cutting speed.

Precipitation Behavior of Supersaturated Solid-solubility CuCrZr Alloy by Additive Manufacturing

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Control of precipitates in CuCrZr alloy

The Influence of Heat Treatment on Microstructure and Properties of Selective Laser Melting CuCrZr Alloy

Effect of heat treatment on CuCrZr alloy fabricated by selective laser melting: Microstructure evolution, mechanical properties and fracture mechanism

Effect of Process Parameters and Heat Treatment on the Microstructure and Properties of CuCrZr Alloy by Selective Laser Melting

Improving the High Temperature Mechanical Performance of Cu-Cr Composite Induced by Residual Nano-Sized Cr Precipitates

Improving the High Temperature Mechanical Performance of Cu–Cr Alloy Induced by Residual Nano-Sized Cr Precipitates

Precipitation Behaviors and the Related Strengthening Mechanism in 2219 Al Alloy Fabricated by Wire Arc Additive Manufacturing

Effect of heat treatments on microstructure, mechanical and electrical properties of Cu–Cr–Zr alloy manufactured by laser powder bed fusion

Effect of heat treatment on the microstructure and properties of CuCrZr alloy manufactured by wire arc additive manufacturing

Performance improvement of laser additive manufactured Cu‒Cr alloy via continuous extrusion

Introduction of nanoprecipitation into supersaturated CoCrFeNiMo0.5 alloy prepared by laser-powder bed fusion via microstructure tailoring to achieve excellent properties

Laser Powder Bed Fusion of Al-Mg-Zr Alloy: Microstructure, Mechanical Properties and Dynamic Precipitation

Revealing Trace Si Effect on Precipitation Behavior and Properties of Cu-Cr-Zr Alloy: Experiments and First-Principles Calculations

Effect of heat treatment on precipitation behavior and mechanical properties of FeCrNi-based medium entropy alloy fabricated by additive manufacturing

3D-AP and Positron Annihilation Study of Precipitation Behavior in Cu–Cr–Zr Alloy

Additively manufactured CuCrZr alloy: Microstructure, mechanical properties and machinability

Enhanced precipitation-hardening of Cu-Ag alloys through controlled chromium addition

Thermodynamic Analysis of the Extension of Solid Solubility of the Cu-Cr System Processed by Mechanical Alloying

Microstructure and Mechanical Properties of Selective Laser Melted Al–2.51Mn–2.71Mg–0.55Sc–0.29Cu–0.31Zn Alloy Designed by Supersaturated Solid Solution