Abstract:Microstructure, texture evolution and mechanical properties of extruded Mg-4.58Zn-2.6Gd-0.18Zr alloy were investigated at extrusion temperatures of 260 °C, 280 °C and 300 °C, extrusion ratios of 10, 15 and 30, and ram speeds of 3 mm s−1 and 6 mm s−1, respectively. The results indicated that the as-cast experimental alloy was composed of α-Mg matrix, coarse α-Mg + W(Mg3Zn3Gd2) eutectic and icosahedral quasicrystalline I(Mg3Zn6Gd) phase. A small amount of undissolved W phases were detected after the homogenization treatment at 505 °C up to 16 h, while most I phase dissolved into the α-Mg matrix. The initial crystallites before extrusion were randomly oriented, and showed a typical random texture. After extrusions, all samples exhibited a bimodal microstructure consisting of fine Dynamic recrystallization (DRX) grains and coarse elongated un-DRX grains, and the formation of ultra-fine DRX grains only occurred in the sample with an extrusion ratio of 10 at 260 °C, 3 mm s−1, which was caused by the solute segregation in homogenized billets and non-uniformly distributed W phase during the extrusion process. A fiber texture with {0002} planes and <1̄21̄0> directions paralleled to the extrusion direction was observed to be dominant in all the extruded samples. Furthermore, the increase of extrusion ratio was found to be beneficial for the DRX process and refinement of grain size, and the maximum texture intensity was accordingly weakened, which resulted in a decrease of tensile yield strength but an increase of elongation. With increasing the extrusion temperature or ram speed, both the grain size and DRX fraction gradually increased. Consequently, the texture was randomized and the maximum texture intensity decreased, which led to a reduction of the elongation and tensile yield strength. The tensile failure behaviors under different extrusion conditions were found to be related with the contraction twin lamellas formed in the un-DRX grains and the string-like W phases.

Significant Disparity of Texture and Strain-Hardening Behavior Induced by TC4 Particle in Extruded Mg Matrix Composite under Tension

Effects of Hot Extrusion on Microstructure and Mechanical Properties of Mg Matrix Composite Reinforced with Deformable TC4 Particles

Improvement of Strength and Ductility of TC4p/AZ91D Magnesium Matrix Composites by Modifying the Extrusion Ratio

Improvement of strength and ductility of TC4 p /AZ91D magnesium matrix composites by modifying the extrusion ratio

Microstructural Regulation and Mechanical Behavior of Asymmetrically Extruded High-Content TC4p Reinforced AZ31 Composite

Promoted Aging Precipitation Behavior of Tc4/Gz151k Magnesium Matrix Composites

Influence of Ti-6Al-4V particles on the interfacial microstructure and strength-ductility synergetic mechanism of AZ91 magnesium alloy

Effect of Ti-6Al-4V Particle Reinforcements on Mechanical Properties of Mg-9Al-1Zn Alloy

Tension-compression Asymmetry of Extruded Mg-Gd-Y-Zr Alloy with a Bimodal Microstructure Studied by In-Situ Synchrotron Diffraction

Study on Microstructure and Mechanical Properties of TC4/AZ31 Magnesium Matrix Nanocomposites

Asymmetric Tension-Compression Mechanical Behavior of the As-Cast Mg-4.58Zn-2.6Gd-0.16Zr Alloy

Effect of Ti Particles on the Microstructure and Mechanical Properties of As-Extruded Titanium-reinforced Mg-9Gd-4Y–1Zn–1Mn Matrix Composites

Asymmetric Tension-Compression Mechanical Behaviors of Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy with Double-Peak Fiber Texture

Effect of hard plate rolling on microstructure and mechanical properties of Mg-9Al-1Zn-based composites reinforced with Ti-6Al-4V particles

Achieving Enhanced Strength-Ductility Synergy in Mg-6Zn-1Mn Alloy by Introducing Deformable Ti Particles

Microstructures and the improved mechanical properties of AZ91 alloy by incorporating Ti-6Al-4V particles

Influence of different extrusion methods on the microstructure, texture evolution and mechanical property of Ti /AZ31 composite

Cyclic Deformation Behavior of a Rare-Earth Containing Extruded Magnesium Alloy: Effect of Heat Treatment

Optimizing the microstructures and enhancing the mechanical properties of AZ81 alloy by adding TC4 particles

Microstructure, Texture Evolution and Tensile Properties of Extruded Mg-4.58Zn-2.6Gd-0.16Zr Alloy

Effect of Ti6Al4V reinforcement particles on the mechanical, wear, and corrosion properties of AZ91D magnesium matrix composites