Abstract:The central diaphragm is often used to reduce the span to maintain the stability and safety of structure in the construction of large-span loess tunnel due to the structure complexities. In this paper, relying on the field monitoring and measurement for Wangcun tunnel in Huangling-Yan’an expressway expansion project, the crown settlement and horizontal convergence of primary support steel rib and central diaphragm steel rib during the construction are analyzed by the upper bench CD method. According to the internal force transfer, deformation coordination, and arch foot displacement between the two structures, the support system is regarded as the arch-beam fixed structure with three times of statically indeterminate and movable abutment under the loads, and the mechanical calculation model of sidewall steel rib and the central diaphragm structure bearing loads and deformation together is established. Finally, through the mechanical model mentioned above, the deformation characteristics of central diaphragm structure and the horizontal convergence in the upper bench of tunnel are calculated and analyzed. The research shows the following: (1) the accumulated settlement of sidewall steel rib in Part I is greater than that of the sidewall steel rib in Part II, and the accumulated settlement of each part at the support structure during the tunnel excavation is less than the reserved deformation of 150 mm specified in the tunnel excavation; (2) the settlement located at the waist and maximum excavation line position of central diaphragm is mainly affected by the excavation of Parts I and II in upper bench; (3) during the whole excavation process, the excavation of Part I and Part II has the greatest influence on the convergence at arch waist and the maximum excavation line position in Part I, and the convergence at the above two positions all experienced four stages of “convergence-expansion-convergence-gradual stability”; and (4) the errors between the horizontal convergence and the deformation of central diaphragm obtained by the mechanical model and the field monitoring data are between 12.7% and 27.5%. The calculated results are in good agreement with the actual situation. The research can provide a theoretical basis for the study of deformation and mechanical properties for support structure in the construction of large-span loess tunnel by the upper bench CD method.

Evaluating the GHG Reduction Efficiency of Underground Construction Technology: Application of a Novel Prefabricated Diaphragm Wall Technology

Performance of a Deep Excavation with the Composite Retaining Wall Using Artificial Ground Freezing Method

Research on carbon emission quantification and evaluation for prefabricated inverted arch construction in drill and blast tunnels

Low-carbon effects of constructing a prefabricated subway station with temporary internal supports: An innovative case of Shenzhen, China

Study of Deformation Behaviors and Mechanical Properties of Central Diaphragm in a Large-Span Loess Tunnel by the Upper Bench CD Method

Comparative Experiment on Adaptive Reuse of Wood Stud Partition Walls: Integrating the DfD Concept into Building Component Design

Experimental study and resilience modeling for prefabricated hollow diaphragm walls of full-assembled underground stations under urban multi-disturbance conditions

GHG Emission Efficiency of Prefabricated Composite Subway Stations: A Novel Case Study of Shenzhen, China

Quantitative methods for predicting underground construction waste considering reuse and recycling

Review of thermal and environmental performance of prefabricated buildings: Implications to emission reductions in China

A Hybrid Construction Method for Shallow Buried Urban Tunnel with Ultra-Small Clear Distance

Sustainability of underground infrastructure – Part 1: Digitalisation-based carbon assessment and baseline for TBM tunnelling

Prefabrication technology for underground metro station structure

Optimization of ventilation efficiency in tunnel-type underground spaces using response surface methodology: a case study of Yunlong Mountain civil defense in Xuzhou

Investigating the impediments to carbon emission mitigation in prefabricated construction: a stakeholder perspective

Optimisation of Parameters and Application of Green Recyclable Precast Hollow Steel Pipe Concrete Supports

Sustainable design for underground environments in modern cities

Big Data-Driven TBM Tunnel Intelligent Construction System with Automated-Compliance-checking (ACC) Optimization

Response of Metro Tunnels to Adjacent Diaphragm Wall Construction in Shenzhen Granite Residual Soil

Carbon-mechanic dual-control design decision model of prefabricated structural components

Research on Carbon Emission of Prefabricated Structure in China