Abstract:To reduce carbon emissions associated with substantial concrete usage in construction and achieve the objectives of green and low-carbon construction, this study innovatively develops a low-carbon binary material by adding limestone powder (LP) and silica fume (SF) into the conventional cement-based material, enhancing the comprehensive utility value of LP. The experimental results show that the addition of 15% LP and 5% SF increases the yield stress of the mortar yet substantially reduces the plastic viscosity to 2.84 Nmm·min, representing a 44.5% decrease compared to pure cement slurry. This reduction is conducive to long-distance pumping of the cement-based material. Moreover, the addition of 5% SF compensates for the 18.8% (mid-stage, 28-d) and 15.8% (late-stage, 90-d) strength loss in mortar caused by LP while simultaneously improving the strength of the co-mixed system by 10.4% (mid-stage) and 10.8% (late-stage). In the early-stage measurements of the LP-SF binary cement-based materials, it is observed that while SF slightly increases the hydration heat release, LP suppresses the early hydration heat release. Therefore, the total heat release observed in the 15% LP and 5% SF group after 72 h is only 254 J/g, demonstrating favorable temperature control and crack prevention effects. In addition, X-ray diffraction (XRD) and thermogravimetric/differential thermogravimetric (TG/DTG) phase analysis reveal a notable increase of 53.56% in CH consumption. Besides, the weight loss on ignition of C-S-H crystals increases, indicating that the secondary hydration of LP and the pozzolanic reaction of SF promote the production of C-S-H in the system. Combined with the late-stage strength and water absorption characteristics, it is concluded that the system exhibits good mechanical properties and compactness. This study presents a use of mixed proportion that enables excellent mechanical properties, good pumping performance, and low hydration heat. Moreover, the analysis indicates that the carbon emission of each cubic meter of the as-developed mortar is reduced by approximately 16.7–23.9%, promoting the efficient and clean utilization of LP and SF.

Improved Mechanical Properties and Fiber Dispersion of Limestone Calcined Clay Cement (lc³) Mortars by Adjusting the Mixing Methods

A Fresh View on Limestone Calcined Clay Cement (LC3) Pastes

Examining the early-stage performance and mechanical performance of limestone powder-silica fume binary cement-based materials

Compressive strength and environmental impact of sustainable blended cement with high-dosage Limestone and Calcined Clay (LC2)

3D printing of calcined clay-limestone-based cementitious materials

3D Printing of Fiber-Reinforced Calcined Clay-Limestone-Based Cementitious Materials: From Mixture Design to Printability Evaluation

Performance of Limestone Calcined Clay Cement (LC3) with various kaolinite contents with respect to chloride transport

Effect of Additives on the Rheological and Mechanical Properties of Microfine-Cement-Based Grout

Use of spent fluid catalytic cracking catalyst (FCC) in Limestone Calcined Clay Cement (LC3) systems: Studies in pastes and mortars

Mechanical Performance of Portland Cement, Coarse Silica Fume, and Limestone (PC-SF-LS) Ternary Portland Cements

Development of gastrin synthesis and posttranslational processing mechanisms in rats.

Effects of packing density and water film thickness on fresh and hardened properties of ternary cement pastes

Influence of C–S–H seed and sodium sulfate on the hydration and strength of limestone calcined clay cement

The Synergistic Effect of Calcained Coal-Series Kaolinite and Limestone on the Hydration of Portland Cement

Effect of different grade levels of calcined clays on fresh and hardened properties of ternary-blended cementitious materials for 3D printing

Mechanical properties and hydration of ultra-high-performance seawater sea-sand concrete (UHPSSC) with limestone calcined clay cement (LC3)

Microstructural investigation and performance of LC3 cementitious materials

Calcined nanosized tubular halloysite for the preparation of limestone calcined clay cement (LC 3 )

Investigation on Hydration and Mechanical Properties of Mortar Containing Limestone Powder and Fly Ash Based on the Coupled Chemical–Thermal–Mechanical Method

Development of a novel eco-efficient LC2 conceptual cement based ultra-high performance concrete (UHPC) incorporating limestone powder and calcined clay tailings: Design and performances

Study on the Influence of Thermoplastic Microcapsules on the Sulfate Resistance and Self-Healing Performance of Limestone Calcined Clay Cement Concrete