Abstract:Scanning Thermal Microscopy (SThM) is one of the most universal methods for probing heat conductivity, interfacial thermal resistance and local temperature of materials and devices with nanoscale resolution. SThM uses a temperature sensitive heated probe with an apex of lateral dimensions ranging from a micrometre down to few nanometers that can contact a studied material or a nanoscale device at an arbitrary point on its surface. The tip-sample contact results in a heat flow from the heated tip to the sample - Qts that reduces a heater temperature Th, that is constantly monitored using a sensitive electronic circuit. SThM primary output signal is the heat flow Qts or a closely related parameter - total heater-sample thermal conductance Gts = Qts/(Th-Ts) where Ts is the temperature of the sample. As the tip scanned in a raster way across the sample surface, SThM output produces “thermal” maps reflecting spatial variations in the local sample thermal conductivity ks with the lateral resolution down to a few nanometers (1). A major challenge is the quantitative interpretation of SThM “thermal” signal as ks is fundamentally entangled with the tip-sample interfacial thermal conductance gif that directly depends on the geometry of the tip-surface contact, a generally unknown value that can also vary significantly during SThM measurements. In this paper we describe three linked approaches that allow to eliminate major variabilities in the SThM measurements as well as produce quantitative measurements of nanoscale thin layers of materials. First, we control the temperature of the sample Ts and the microscope base Tm via actively controlled Peltier heating/cooling elements with ~10 mK precision significantly improving the reproducibility of SThM signal by approximately 10 fold. Secondly, we use simultaneous measurement of shear forces and heat flow between the probe (2). As shear forces directly proportional to the contact area, the correlation observed allowed us to confirm the true ballistic nature of heat transport via nanoscale contacts in such a system, suggesting that even large – sub-micrometer sized contacts are composed by a multiple nanoscale junctions with the size below the mean-free-path of the heat carriers. Shear forces SThM allowed us to eliminate dependence of the SThM output on the most difficult to determine parameter – tip-surface contact geometry. Finally, we present a new paradigm of measurement of thermal conductance in the nanoscale thin layers of materials by producing a nanoscale cross-section of the material or device via SPM-friendly Ar ion polishing producing near-atomically low-angle wedge-shaped flat sections (3), followed by the SThM measurements of total thermal conductance Gts as a function of the wedge thickness t. The decrease of the thermal conductance as a function of edge thickness dGts/dt allows to exclusively determine thermal conductivity of the sample kts, eliminating necessity to know either the tip-sample interfacial thermal conductance gif or layer-substrate thermal conductance, two notoriously unknown parameters that render majority of SThM measurements to be merely qualitative.

Analysis of Heat Flow in Modified Transient Plane Source (MTPS) Measurements of the Thermal Effusivity and Thermal Conductivity of Materials.

Theoretical Accuracy of Anisotropic Thermal Conductivity Determined by Transient Plane Source Method

An Approximate Analytical Method for Nonlinear Transient Heat Transfer Through a Metallic Thermal Protection System

Invited Article: Micron Resolution Spatially Resolved Measurement of Heat Capacity Using Dual-Frequency Time-Domain Thermoreflectance.

Analysis and Improvement of the Hot Disk Transient Plane Source Method for Low Thermal Conductivity Materials

Improving the accuracy of the transient plane source method by correcting probe heat capacity and resistance influences

A Noncontact Method for Measuring Thermal Conductivity and Thermal Diffusivity of Anisotropic Materials

Automatic Algorithm Applied for Calculating Thermal Conductivity by Transient Plane Source Method

A Modified Step-Wise Transient Method For Measuring The Thermal Conductivity Of Anisotropic Materials

Thermometry and Thermal Transport in Micro/Nanoscale Solid-State Devices and Structures

Thermophysical Property Measurement of Thermal Protective Material by Guarded Plane Source Method

Optical Measurements of Thermal-Diffusivity of A Material

On the dynamic thermal conductivity and diffusivity observed in heat pulse experiments

Simultaneous Measurement of Thermal Conductivity and Heat Capacity Across Diverse Materials Using the Square-Pulsed Source (SPS) Technique

Measurement Method of Thermal Conductivity of Fabrics Based on TPS and MTPS

The Application of the Finite Elements Method in the Transient Measurements of Thermophysical Parameters

Measurement of Thermal Conductivity and Thermal Diffusivity for Materials on Transient Hot-Plane Method

Analysis of radiation effect on thermal conductivity measurement of semi-transparent materials based on transient plane source method

Measurements of nanoscale thermal properties of materials via Scanning Thermal Microscopy (SThM):Challenges and solutions

A laser-based Ångstrom method for in-plane thermal characterization of isotropic and anisotropic materials using infrared imaging

Analytical Methods for Determination of Heat Transfer Fields from Temperature Sensitive Paint Measurements in Hypersonic Tunnels