Abstract:AbstractThe search for suitable friction materials for high-speed train is an attractive but difficult problem. In recent years, a variety of different novel friction materials were fabricated to meet the aims of high loads and speeds under ambient environment. Carbon fiber-reinforced carbon composites (C/C), carbon fiber-reinforced silicon carbide composites (C/C-SiC) and metallic composites fabricated by powder metallurgy are three excellent materials among them. Here a comparison of these three different materials working as brake pads, coupled with high-density C/C-SiC brake disk, was described. All the experiments were conducted using the same procedure with increasing initial braking speed (the rotation speed of brake disk at the beginning of braking process) from 30 to 59 m/s and constant load of 1.25 MPa, simulating the real working condition of high-speed train. The coefficient of friction (COF) and wear rates of three materials were compared and analyzed. During experiments, the COF of metallic and C/C pads remains nearly constant at 0.31 and 0.22, respectively, with increasing braking speed, while that of C/C-SiC exhibits a parabola. These different trends of COF may be attributed to the distinctive forming processes of friction film on the top of contact surfaces. Meanwhile, the wear rates of metallic composites increase rapidly from 683 to 1803 mm3/MJ with initial braking speed, while C/C-SiC presents the highest wear loss of 1887 mm3/MJ at 49 m/s and lowest value of 315 mm3/MJ at 59 m/s. Interestingly, the wear rate of C/C composites, due to the appropriate bonding strength of matrix/fiber and relatively high shear stress, decreases from 3698 to 903 mm3/MJ with increasing initial braking speed, which does not consist with pre-existing paper. Thus, metallic pads presented the lowest wear rates at lower speed (<49 m/s) but the highest at high speed, while C/C-SiC composite pads showed the greatest wear resistance at high speed. This investigation of three different friction materials will enhance our understanding of these friction materials and benefit the selection and safe application of high-speed train friction materials.

Friction and Wear Mechanics of Fe-based PM Pad Paired with C/C-SiC Disc under High-Speed Braking

Friction and Wear Mechanics of Fe-Based PM Pad Paired with Carbon Fiber-Reinforced Silicon Carbide (C/C-SiC) Disk Under High-Speed Braking

Braking Performance of Fe-Based and Cu-Based Powder Metallurgy Pads Paired with C/C-SiC Disk on Full-Scale Dynamometer

Braking behaviors of Cu-based PM brake pads mating with C/C–SiC and 30CrMnSi steel discs under high-energy braking

Comparison of Braking Behaviors Between Iron- and Copper-Based Powder Metallurgy Brake Pads That Used for C/C–SiC Disc

Investigation on Braking Performance and Wear Mechanism of Full-Carbon/ceramic Braking Pairs

Oxidation Behaviour of C/C–SiC Brake Discs Tested on Full-Scale Bench Rig

Preparation and Dynamometer Tests of 3D Needle‐Punched C/C‐SiC Composites for High‐Speed and Heavy‐Duty Brake Systems

Comparison of Friction and Wear Behavior Between C/C, C/C-SiC and Metallic Composite Materials

Dry Sliding Wear Studies of Cu-Based Powder Metallurgy Brake Materials

Effect of Cu Addition on the Braking Performance of Fe–Si Alloy-Modified C/C–SiC Brake Materials

Study on the Particle-Reinforced Cu-Matrix Brake Pads for 300 Km·h-1 High-Speed Trains

Fading behavior and wear mechanisms of C/C–SiC brake disc during cyclic braking

Modifying C/C–SiC brake pads with different Fe–Si alloy phases to improve the wear resistance of full-carbon/ceramic brake pair

Tribological Behaviour and Mechanism of C/C-SiC-Fe Composites at Different Braking Speeds

Effect of Braking Speed on Frictional Properties of Short Fiber C/C-Sic Brake Materials and Grey Cast Iron

Mechanical and Microstructure Characterisation of 2.5D C/C-SiC Composites Applied for the Brake Disc of High-Speed Train

Coupled thermal-structural analysis of an axle mounted C/C-SiC brake disc for high-speed trains

Tribological Properties of Short Fiber C/SiC Brake Materials and 30crsimova Mate

Thermo-Mechanical Coupling Analyses for Al Alloy Brake Discs with Al2O3-SiC(3D)/Al Alloy Composite Wear-Resisting Surface Layer for High-Speed Trains

Braking behaviours of C/C-SiC mated with iron/copper-based PM in dry, wet and salt fog conditions