Abstract:This paper proposes a novel approach that employs error amplification and ADC-based dual-mixer time-difference (ADC-based-DMTD) technique for high-precision locking of laser repetition frequency with compact size. This electronic system consists of two main components: a digitized error amplification module (EAM) and an FPGA-based digital frequency locking module (DFLM). The EAM mainly integrates a configurable frequency generator (CFG), a configurable frequency multiplier (CFM) and a mixer to process the laser pulses and a high-stability reference source (e.g., an atomic clock), enabling high-precision locking of pulse lasers operating at different repetition frequencies. By employing frequency multiplication and mixing, the EAM amplifies the laser's frequency error and performs frequency down-conversion, enhancing measurement sensitivity and reducing the hardware requirements of the back-end. The DFLM receives the EAM outputs by using an ADC-based-DMTD method to precisely measure frequency errors, then the digital proportional-integral-derivative (PID) controller provides feedback to achieve accurate frequency locking. Initial testing with a voltage-controlled oscillator (VCO) demonstrated excellent locking performance, achieving an Allan deviation of $9.58 \times 10^{-14}$ at 10 seconds and a standard deviation (STD) of 7.7 \textmu Hz root mean square (RMS) after locking, marking a five-order-of-magnitude stability enhancement. In laboratory experiments with a custom-built femtosecond fiber laser, the system achieved robust locking of the repetition frequency, with a stability improvement from $1.51 \times 10^{-7}$ to $1.12 \times 10^{-12}$ at a 10-second gate time and an STD of 0.43 mHz RMS after locking.

Reduction of Timing Jitter with Active Control in a Khz Regenerative Amplifier of Femtosecond Pulse Ti:Al2O3 Laser

Timing Jitter in a Kilohertz Regenerative Amplifier of a Femtosecond-Pulse Ti:Al(2)O(3) Laser.

Pulsed Light Time-of-flight Measurement Based on a Differential Hysteresis Timing Discrimination Method.

Sub 100fs Timing Jitter Of Mode-Locked Laser

Yoctosecond Timing Jitter Sensitivity in Tightly Synchronized Mode-Locked Ti:Sapphire Lasers

Highly Stable Synchronized Femtosecond Ti:sapphire Laser with 1.3 W Powers and Sub-Femtosecond Timing Jitter

Jitter-calibrated Second-Order Correlation Measurement for Pulsed Excitation with Low Repetition Rate

Sub-10-Attosecond Timing Jitter Mode-Locked Ti:sapphire Lasers

Independently tunable 1.3 W femtosecond Ti:sapphire lasers passively synchronized with attosecond timing jitter and ultrahigh robustness.

Timing Delay Jitter Compensation of a Fiber Link with Active Delay Compensation

Timing Jitter Sensitivity on Beam Dynamics in Photocathode RF Gun

Control of Carrier-Envelope Phase Offset in Femtosecond Laser with PLL and TV-Rb Clock

Efficient amplification of a femtosecond Ti:sapphire laser with a ring regenerative amplifier

Phase-resolved measurement and control of ultrafast dynamics in terahertz electronic oscillators

A pulse-to-pulse timing jitter measurement between two synchronized amplified laser beams for TTX.

High Time Resolution Beam-Based Measurement of the Rf-To-Laser Jitter in A Photocathode Rf Gun

A Compact and Robust Regenerative Amplifier Pump Source for High Repetition Rate Terahertz Parametric Amplifier

A Digital and Compact High-Precision Locking System for Pulse Laser Repetition Frequency

Efficient timing jitter simulation for passively mode-locked semiconductor lasers

Timing Jitter Reduction Through Relative Intensity Noise Suppression in High-Repetition-rate Mode-Locked Fiber Lasers

1 kHz, 10 mJ, sub-200 fs regenerative amplifier utilizing a dual-crystal configuration of Yb:CaGdAlO_4 featuring exceptional beam quality