Abstract:Lean-burn natural-gas spark-ignition combustion inside a diesel geometry is characterized by two distinct and successive events: a rapid burning process inside the piston bowl, followed by a much slower burn inside the squish region. This paper used experimental data (including images of flame natural luminosity) to investigate the magnitude and phasing of these two combustion stages. The results showed a substantial impact on the parameters generally used to investigate the combustion phenomena in spark-ignition engines (e.g., the 10-to-90-percent energy release). A better solution to identify the start and end of the rapid- and the slow-burning stages in such an engine is to use the inflection points in the apparent rate of heat release. Moreover, as the higher turbulence in a diesel-like environment accelerates flame inception, the 5% or 10% energy release used traditionally to define the flame inception period should not be used for these engines because the enflamed zone already reached an appreciable size at the two corresponding crank angle degrees. Further, the 2nd inflection point in the apparent rate of heat release (i.e., the point where the slow-burning stage started to dominate the heat release) was much advanced compared to 90% energy release generally used to define the end of the rapid-burning stage in conventional stoichiometric spark-ignition engines. Furthermore, as the slow-burning stage was characterized by a lower flame propagation speed, a lower fuel fraction burning during this stage would increase the engine combustion efficiency. Furthermore, a more advanced phasing of the late-burning stage relative to the fast-burn stage would result in a more optimal combustion environment (i.e., higher in-cylinder pressure and temperature), which would further improve the engine efficiency and probably reduce carbon monoxide and unburned hydrocarbon emissions. As a result, this study suggests that the combustion strategy of such converted diesel engines should advance and optimize the mass of fuel that burns inside the squish region.

Utilization of Non-Firing Cycle Exhaust Gases to Improve Diesel Engine Combustion During Cold Start Process

Multiple Combustion Stages Inside a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark-Ignition Operation

Methodology to Determine the Fast Burn Period Inside a Heavy-Duty Diesel Engine Converted to Natural Gas Lean-Burn Spark Ignition Operation

Methodology to Separate the Two Burn Stages of Natural-Gas Lean Premixed-Combustion Inside a Diesel Geometry

Analysis of Two-Stage Natural-Gas Lean Combustion Inside a Diesel Geometry

Lessons from the Conversion of a Heavy-Duty Compression Ignition Engine to Natural Gas Spark Ignition Operation

Experimental Setup of Combustion Visualization Inside a Heavy-Duty Diesel Engine Converted to Natural-Gas Spark-Ignition Operation

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

An Assessment of the Application of Catalyst Preheating Prior to Engine Cold Start to Improve the Filtration Performance of CDPF on Particulate Emissions

Twin-Peak Heat Release Phenomenon Inside a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

Intake Air Heating Strategy to Reduce Cold-Start Emissions from Diesel Engines

Reducing Cold Start Emissions from Automotive Diesel Engine at Cold Ambient Temperatures

Experimental study on in-cylinder combustion and exhaust emissions characteristics of natural gas/diesel dual-fuel engine with single injection and split injection strategies

Combustion Process and Emissions of A Heavy-Duty Engine Fueled with Directly Injected Natural Gas and Pilot Diesel

Improving Cold Start and Transient Performance of Automotive Diesel Engine at Low Ambient Temperatures

Cold and Warm Start Characteristics using HVO and RME Blends in a V6 Diesel Engine

Modeling Heavy-Duty Engine Thermal Management Technologies to Meet Future Cold Start Requirements

Exploring the Combustion Performance of a Non-Road Air-Cooled Two-Cylinder Turbocharged Diesel Engine

Combustion and Emission Characteristics of an Electronically-Controlled Common-Rail Dual-Fuel Engine

The effect of ignition diesel injection conditions on the combustion process of natural gas engine