Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Research on W-Mo-Y Plasma Surface Alloying Process and Microstructure of Alloying Layer

Multiple Needle Cathodes Plasma Surface Alloying of Ti6Al4V with W-Mo-C-N

Investigation on Multi-Element Ni–Cr–Mo–Cu Alloying Layer by Double Glow Plasma Alloying Technique

Characterisation and Oxidation Behaviour of Plasma Surface Alloyed on Γ-Tial Alloy

Ni-based Superalloy Surface Alloying by Double-Glow Plasma Surface Alloying Technique

High-temperature oxidation behavior of double glow plasma Cr-Y alloyed layers on Ti 2 AlNb alloy

Effect of Y2O3 on the Properties of Plasma Arc Coating on the Surface of Steel

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Phase, Microstructure and Properties Evolution of Fine-Grained W–Mo–Ni–Fe Alloy During Spark Plasma Sintering

Research of the microstructure of the Co-Cr-W alloy plasma surfacing

Substrate dilution and interface structures of tungsten coating deposited by double-glow plasma surface alloying on stainless steel substrate

Effect of Molybdenum on Microstructure and Wear Resistance of Iron-based Alloy Coating Clad by Plasma Transferred Arc Process

Experimental Investigation on Characteristics of Valve Sealing Face by Double Glow Plasma W Alloying Process and Carburizing

Microstructure, wear and electrochemical behaviors of laser cladding Fe-based coatings with various molybdenum contents

Research Progress of Effects of Mo and W on Microstructure and Key Properties of Ni-based Single Crystal Superalloys

Microstructure and Application of Surface after Laser Alloying on Surfacing Layer

Orthogonal Parameter Optimization of Mo-W Coating on 45CrNiMoVA Steel Surface

Study on Microstructures and Tribological Performance of Ion Plating Mo Layer

Effect of Molybdenum on Microstructure and Properties of Cobalt-Based Alloy Coating Deposited by Plasma Transferred Arc Process

Effects of Y2o3 on the Microstructure and Wear Resistance of Cobalt-Based Alloy Coatings Deposited by Plasma Transferred Arc Process

Effect of Y2O3 Addition on the Microstructure, Wear Resistance, and Corrosion Behavior of W-4.9Ni-2.1Fe Heavy Alloy