Comparative End-of-Life Study of Polymer and Paper Based Radio Frequency Devices

Rajeev Kanth,Pasi Liljeberg,Yasar Amin,Qiang Chen,Li‐Rong Zheng,Hannu Tenhunen

2012-01-01

The International Journal of Environmental Protection

Abstract:In this work end-of-life (EOL) analysis of polymer and paper based radio frequency devices have been carried out. Polymer and paper based RFID antenna has been chosen as a radio frequency device. A ...

What problem does this paper attempt to address?

Life cycle assessment of printed antenna: Comparative analysis and environmental impacts evaluation

rajeev kumar kanth,qiansu wan,harish kumar,pasi liljeberg,lirong zheng,hannu tenhunen

DOI: https://doi.org/10.1109/ISSST.2011.5936899

2011-01-01

Abstract:This paper presents cradle to grave life cycle assessment of printed electronics resources. In this work, an attempt has been made to investigate and evaluate the life cycle assessment and environmental impacts of printed electronics resources such as polymer substrate-printed RFID antenna. Life cycle inventory analysis for these resources has been carried out to quantify total systems' inputs and outputs that are relevant to the environmental impacts especially emissions to air, fresh water, industrial soil and sea water.
RF Interconnections for Paper Electronics

Longhan Xie,Yongqiang Feng,Geng Yang,Qiang Chen,Lirong Zheng

DOI: https://doi.org/10.1109/lmwc.2015.2468572

IF: 3

2015-01-01

IEEE Microwave and Wireless Components Letters

Abstract:Low temperature and the fragility features of paper substrate require novel approach for the heterogeneous integration of silicon chip and printed components. In this letter, RF interconnection via capacitive coupling is proposed for printed paper electronics. Capacitive coupling combined with the printed transmission line is used as the signal channel and realizes chip-to-chip communication. Modulation such as orthogonal frequency-division multiplexing is used for multiple chips to share the same transmission channel and increase the data rate. The channel response of the RF interconnection is studied and the feasibility is evaluated.
Evaluating sustainability, environment assessment and toxic emissions in life cycle stages of printed antenna

rajeev kumar kanth,qiansu wan,harish kumar,pasi liljeberg,qiang chen,lirong zheng,hannu tenhunen

DOI: https://doi.org/10.1016/j.proeng.2012.01.891

2012-01-01

Procedia Engineering

Abstract:In this work cradle to grave life cycle assessment of printed electronics resources have been presented. An attempt has been made to investigate and evaluate the life cycle assessment and environmental impacts of printed electronics resources such as polymer substrate-printed RFID antenna. Life cycle inventory analysis for these resources has been carried out to quantify total systems’ inputs and outputs that are relevant to the environmental impacts especially emissions to air, fresh water, industrial soil and sea water. The results show that printed electronics materials are considerably more environment friendly than materials needed for PCB electronics. We have obtained the mass of emissions in each life cycle stages which verify that technology wise printed antenna causes less harmful and hazardous impacts to the environment.
Electromagnetic Environment of Uhf-Rfid

Song Li,Xue-tao Weng

DOI: https://doi.org/10.1109/eptc.2008.4763566

2008-01-01

Abstract:The number of applications that use radio-frequency identification (RFID) technology has grown continually in the last few years. In this presentation we will present the results of research on the electromagnetic environment on RFID systems. We analyze the effects of UHF MHz China RFID system near a GSM frequency bands. Kurokawa's method of calculating the power reflection coefficient from the Smith chart in the situation is applied to passive RFID tag design. The performance analysis of a specific RFID tag is presented to be compared with the theory. One of our objectives has been to examine tag designs that are less sensitive to their environment, in that their radiation patters and tag response characteristics change little when placed on different distance and orientation. We introduce a technique for deploying RFID systems and engineering solutions based on fundamental electromagnetic understanding. The paper will also explore tag designs that use electromagnetic models to simulate and engineer RFID systems.
Evaluating Sustainability, Environmental Assessment and Toxic Emissions During Manufacturing Process of RFID Based Systems

Rajeev Kumar Kanth,Pasi Liljeberg,Hannu Tenhunen,Qiansu Wan,Yasar Amin,Botao Shao,Qiang Chen,Li-Rong Zheng,Harish Kumar

DOI: https://doi.org/10.1109/dasc.2011.175

2011-01-01

Abstract:The present state of the art research in the direction of embedded systems demonstrate that analysis of life-cycle, sustainability and environmental assessment have not been a core focus for researchers. To maximize a researcher's contribution in formulating environmentally friendly products, devising green manufacturing processes and services, there is a strong need to enhance life-cycle awareness and sustainability understandings among embedded systems researchers, so that the next generation of engineers will be able to realize the goal of a sustainable life-cycle. In this work an attempt has been made to investigate and evaluate the life-cycle management and environmental assessment in fabricating processes of the RFID based systems. We have chosen a general life cycle assessment approach which involves the collection and evaluation of quantitative data on the inputs and outputs of materials and energy associated with the RFID based systems. Based on the developed generic models, we have obtained the results in terms of environmental emissions for a production of paper substrate printed RFID antennas. We also make an attempt to raise several sustainability issues and quantify the toxic emissions during the manufacturing process.
Performance-optimized Printed Wideband RFID Antenna and Environmental Impact Analysis

Yasar Amin,Rajeev Kanth,Pasi Liljeberg,Qiang Chen,Li‐Rong Zheng,Hannu Tenhunen

2013-01-01

ETRI Journal

Abstract:This paper presents performance optimized RFID tag antenna, developed by using commercially accessible paper substrates and advanced inkjet printing process to guarantee mechanical flexibility and ...
Design And Analysis Of Efficient And Compact Antenna For Paper Based Uhf Rfid Tags

Yasar Amin,Qiang Chen,Botao Shao,Julius Hallstedt,Hannu Tenhunen,Li-Rong Zheng

DOI: https://doi.org/10.1109/ISAPE.2008.4735140

2008-01-01

Abstract:Paper substrate is one of the paramount nominees for Radio Frequency Identification (RFID) tags but at the same time it is extremely prone towards environmental changes. In this paper, antennas for UHF RFID tags on paper based substrate are investigated and analyzed for the first time to evaluate the effect of change in dielectric constant on the antenna parameters and performance. On the basis of analysis a concrete meander line antenna is proposed, designed and evaluated which has tremendous immunity towards variation in dielectric constant.
Electromagnetic Analysis of Radio Frequency Identification Antennas for Green Electronics

Yasar Amin,Botao Shao,Qiang Chen,Li-Rong Zheng,Hannu Tenhunen

DOI: https://doi.org/10.1080/02726343.2013.777324

IF: 1.042

2013-01-01

Electromagnetics

Abstract:This article demonstrates in-depth electromagnetic analysis of a radio frequency identification tag antenna manufactured by inkjet printing technology on different paper substrates to achieve ultra-low cost flexible radio frequency identification tags using a novel hole-matching technique for reducing the consumption of substrate material, and conductive ink. Nevertheless, the electromagnetic properties of the paper substrate are vulnerable to various environmental effects. Thus, the proposed antenna design is optimized for consistent wideband performance throughout the complete UHF radio frequency identification band (860960 MHz) while presenting a greater degree of material insensitivity. An advanced antenna design methodological analysis is performed to accomplish an extended read range, while exhibiting benchmarking results when across cardboard cartons filled with metal or water containing objects.
Environmental aging of reinforced polymer composite radome: reliability and performance investigation

Imran Haider,Iftikhar Hussain Gul,Shahid Aziz,Muhammad Iftikhar Faraz,Muhammad Ali Khan,Syed Husain Imran Jaffery,Dong-Won Jung

DOI: https://doi.org/10.3389/fmats.2024.1427541

2024-07-25

Frontiers in Materials

Abstract:In high-speed microelectronic communication, efficient and reliable radome-enclosed antenna performance is highly desired, which depends on consistent dielectric, mechanical properties, and low moisture absorption. The purpose of this study is to investigate the dielectric properties of fiber-polymer matrix composite (PMC) radome over wideband frequency and the impact of environmental aging on its performance. The dielectric constant (Ɛ r ) of the SF/E 0.8 (80% fiber loading) composite radome material decreased to 4% from its original value (3.93), and dielectric loss (δ) was reduced by 11% from 0.035 (2–18 GHz), while SEM morphology indicated fair interface bonding. Employing the Hallberg and Peck model, equivalent aging time (5–25 years), upon accelerated environmental aging, Ɛ r was increased up to 3.69%, δ to 9.68%, and the moisture uptake in the SF/E 0.8 composite was increased from 1.13% to 1.67%, while tensile strength was retained up to 90.62% of its original value (147.83 MPa), compression strength up to 93.56% of its original value (388.54 MPa), flexural strength up to 85.44% of its original value (286.77 MPa), and interlaminar shear strength up to 77.66% of its original value (22.03 MPa), respectively. SF/E 0.8 radome-enclosed antenna gain was decreased to 1%, and the voltage standing wave ratio (VSWR) was increased to 1.04% from their original values. This gradual and small deviation of SF/E x composite properties and radome electrical performance over the extended aging time is referred to as reliable and effective for radome applications.

materials science, multidisciplinary
Evaluation of design alternatives of End-Of-Life products using internet of things

Aditi D. Joshi,Surendra M. Gupta

DOI: https://doi.org/10.1016/j.ijpe.2018.12.010

IF: 11.251

2019-02-01

International Journal of Production Economics

Abstract:Internet of Things (IoT) can play a crucial role in End-of-Life (EOL) product recovery. It can help in determining conditions of returned EOL products with the help of sensors and RFID tags, which then can be used to decide a feasible recovery process for the EOL product amongst disassembly, remanufacturing, recycling or disposal. Product design is a key criterion which affects the choice of recovery process. Complex product designs will increase the cost of disassembly which will lead to higher recovery costs. Therefore, considering the recovery operations during a product's design phase can lead to effective recovery process after its EOL. In order to see the effect of product design on product recovery using IoT, this paper proposes an Advanced-Remanufacturing-To-Order-Disassembly-To-Order (ARTODTO) system which receives sensors and Radio Frequency Identification (RFID) tags embedded End-Of-Life (EOL) products to satisfy various products, components and materials demands. The received EOL products can be recovered via disassembly to meet the components demands, remanufactured to meet the products demands or recycled to meet the materials demands. The remaining EOL products can be disposed of. The model evaluates different designs of a product for the ease of disassembly and remanufacturing based on three criteria viz., total profit, quality level and the number of disposed items. To solve the proposed multi-criteria decision-making model, linear physical programming is used. An example of laptops is considered for illustration of the proposed methodology.
Materials for Bioresorbable Radio Frequency Electronics

Suk‐Won Hwang,Xian Huang,Jung‐Hun Seo,Jun‐Kyul Song,Stanley Kim,Sami Hage‐Ali,Hyun‐Joong Chung,Hu Tao,Fiorenzo G. Omenetto,Zhenqiang Ma,John A. Rogers,Suk-Won Hwang,Jung-Hun Seo,Jun-Kyul Song,Sami Hage-Ali,Hyun-Joong Chung

DOI: https://doi.org/10.1002/adma.201300920

IF: 29.4

2013-05-17

Advanced Materials

Abstract:Materials, device designs and manufacturing approaches are presented for classes of RF electronic components that are capable of complete dissolution in water or biofluids. All individual passive/active components as well as system-level examples such as wireless RF energy harvesting circuits exploit active materials that are biocompatible. The results provide diverse building blocks for physically transient forms of electronics, of particular potential value in bioresorbable medical implants with wireless power transmission and communication capabilities.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
A comparative study of EMI shielding effectiveness of metals, metal coatings and carbon-based materials

Jeevan Kittur,Bhavya Desai,Rakesh Chaudhari,Praveen Kumar Loharkar

DOI: https://doi.org/10.1088/1757-899x/810/1/012019

2020-03-01

IOP Conference Series: Materials Science and Engineering

Abstract:Abstract The increased use of electronic gadgets across almost all fields in the fast progressing 21 st century has resulted in a new type of pollution. This pollution can be fatal for animals, humans as well as electronic gadgets. This new form of pollution is nothing but the electromagnetic interference or radio-frequency interference. When these harmful electromagnetic waves come in contact with the electronic devices, it causes them to malfunction thus resulting into damage of the costly equipment. Hence comes the need to protect the electronic gadgets and systems of commercial as well as defence fields from these harmful waves by providing a shielding effect. The review is a study of materials used for shielding like coated nano-fibers, nano-composites, metals, conducting polymers and carbon nanotubes (CNTs).
Development and Analysis of Flexible Uhf Rfid Antennas for "green" Electronics

Y. Amin,Q. Chen,L. -R. Zheng,H. Tenhunen

DOI: https://doi.org/10.2528/pier12060609

2012-01-01

Abstract:In this paper, novel Bowtie antennas which cover complete UHF RFID band (860-960 MHz), fabricated on various ultra-low-cost substrates using state-of-the-art printing technologies are investigated as an approach that aims to accommodate the antenna during the package printing process whilst faster production on commercially available paper. The proposed antenna structures are evaluated in reference to circuit and field concepts, to exhibit extreme degree of functional versatility. These antennas are developed to cater the variations which appear in electromagnetic properties and thickness of paper substrate due to various environmental effects. Computed (simulated) and well-agreed measurement results confirm a superior performance of the tag modules while stepping towards next generation of "green" tags.
Optimisation Design For Eeprom Embedded In Uhf-Rfid Passive Transponders

MingChun Li,LiWu Yang,Jinfeng Kang,Yangyuan Wang

DOI: https://doi.org/10.1080/00207217.2010.497678

2011-01-01

International Journal of Electronics

Abstract:Low cost and low power are the major requirements for radio-frequency identification (RFID) applications. In this article, optimisation techniques on ultra-high frequency (UHF) RFID passive transponders are proposed to achieve low power without loss of area. The optimisations cover the key sub-circuits, such as the charge pump, discharge scheme and sense amplifier in the embedded electrically erasable programmable read-only memory (EEPROM) of UHF RFID-passive transponders. A 256-byte EEPROM for UHF RFID application with an 0.8 mm x 0.7 mm chip area was designed and manufactured based on an SMIC 0.18 mu m EEPROM process. The simulations and measurements show that, compared to the conventional design, a reduced power loss of more than 20% is achieved without a loss in the chip area.
Compaction Uniformity and Environmental Adaptability of Printed RFID Antenna

Yuanming Chen,Wei He,Guoyun Zhou,Xuemei He

DOI: https://doi.org/10.1109/icasid.2010.5551339

2010-01-01

Abstract:The manufacture of RFID antenna tags (RFIDs) using silk-screen printing technology with conductive silver paste is one of economic methods to reduce the cost of RFIDs. The distance between conductive particles is minified via hot compaction to conductive silver paste, resulting in lower resistance and higher Q value. The compaction conditions, including temperature, pressure and time, were systematically studied based on the analysis method of uniform design, with regression equation by nonlinear regression analysis fitted by Minitab Statistical Analysis Software. The effect of environmental factors to resistance of RFID antenna was also studied through the high and low temperature impact test and the constant temperature and humidity test. The results indicate that resistance of RFID antenna printed with conductive silver paste can be reduced more than 50%, the resistance variation of RFID antenna can be predicted by regression equation with correlation coefficient 99.8% in certain range and antenna printed with conductive silver paste have good environmental adaptability.
Proposed Methodology for End-of-Life Option using Multi Criteria Decision Analysis: A Study for General Paper Product

Salwa Mahmood,Muhammad Aizrul Ezuan Edirudzin,Nur Syamimi Jiran

DOI: https://doi.org/10.47836/pjst.29.4.40

2021-10-29

Pertanika Journal of Science and Technology

Abstract:Over the years, the world population has been growing exponentially. This population growth affects the number of waste products due to the increased production, which leads to greater environmental impact and other problems. There are different numbers of product end-of-life (EOL) options to handle waste based on product characteristics. This research is designed to develop a methodology to determine the best EOL option for a paper product using the analytical hierarchy process (AHP). AHP is one of the multi-criteria decision analysis (MCDA) methods employed to select the best option by considering the user’s preferences and output of competing EOL options related to different product criteria. A graphical user interface (GUI) called AHP-based software was developed using Microsoft Excel through the programming function of Visual Basic for Applications as a user facilitating tool when conducting the analysis. The case study technique is applied to five different types of paper products to assess the capability of the proposed AHP-based software. Results from the AHP-based software reveal that recycling is the most suitable EOL technique for most paper products compared to other techniques. However, polluted products with ink or food waste and coating may not be suitable for this method. The research assists the users to identify the most sustainable ways to handle paper product waste based on the product condition.
Disassembly planning and sequencing for end-of-life products with RFID enriched information

Hung-da Wan,Venkata Krishna Gonnuru

DOI: https://doi.org/10.1016/j.rcim.2012.05.001

2013-06-01

Abstract:When a product reaches its end of lifecycle, components of the product can be reused, recycled, or disposed, depending on their conditions and recovery value. In order to make an optimal disassembly plan to efficiently retrieve the reusable and recyclable items inside a product, knowing the true condition of each component is essential. Practically, the recovery value of a used product is often estimated roughly via visual inspection, and the inaccurate estimates would lead to suboptimal disassembly plans. This paper proposes the use of radio-frequency identification (RFID) technology to support disassembly decisions for end-of-life products. RFID can track pertinent data throughout a product’s lifecycle. With the enriched information, a fuzzy-based disassembly planning and sequencing model is proposed to maximize net profit. First, a Bayesian method translates the RFID data into a quality index of the components. Then, a fuzzy logic model, solved by genetic algorithm, synthesizes input variables (i.e., product usage, component usage, and component condition) into a solution of optimal disassembly sequence that maximizes profit considering recovery value and disassembly cost. This paper verifies the merits of using RFID to improve disassembly decisions that help reuse and recycle end-of-life products to reduce environmental impact.

robotics,computer science, interdisciplinary applications,engineering, manufacturing
Importance of Computational Electromagnetic Modeling in the Development of RFID Tags for Paper Reel Identification

leena ukkonen,toni bjorninen,lauri sydanheimo,atef z elsherbeni,fan yang

2010-01-01

Abstract:Development of the RFID tag for paper reel identification in industrial environment is discussed. Paper reel supply chain and history of the development of the presented antenna design is explained. Modeling of the paper reel tag is discussed and a case study of tag antenna paper reel co-design is presented.
Design and Analysis of Analog Front-End of Passive RFID Transponders

Jianyun Hu,Yan He,Hao Min

DOI: https://doi.org/10.3969/j.issn.1674-4926.2006.06.009

2006-01-01

Abstract:An analog front-end of HF passive RFID transponders compatible with ISO/IEC 18000-3 is presented.Design considerations, especially the power transmission in the RFID transponder, are analyzed. Based on these considerations,an analog front-end is presented with novel architecture, high power conversion efficiency, low voltage, low power consumption, and high performance in an environment of noise and power fluctuation. The circuit is implemented in a Chartered 0.35μm standard CMOS process. The experimental results show that the chip can satisfy the design target well.

Comparative End-of-Life Study of Polymer and Paper Based Radio Frequency Devices

Life cycle assessment of printed antenna: Comparative analysis and environmental impacts evaluation

RF Interconnections for Paper Electronics

Evaluating sustainability, environment assessment and toxic emissions in life cycle stages of printed antenna

Electromagnetic Environment of Uhf-Rfid

Evaluating Sustainability, Environmental Assessment and Toxic Emissions During Manufacturing Process of RFID Based Systems

Performance-optimized Printed Wideband RFID Antenna and Environmental Impact Analysis

Design And Analysis Of Efficient And Compact Antenna For Paper Based Uhf Rfid Tags

Electromagnetic Analysis of Radio Frequency Identification Antennas for Green Electronics

Environmental aging of reinforced polymer composite radome: reliability and performance investigation

Evaluation of design alternatives of End-Of-Life products using internet of things

Materials for Bioresorbable Radio Frequency Electronics

A comparative study of EMI shielding effectiveness of metals, metal coatings and carbon-based materials

Development and Analysis of Flexible Uhf Rfid Antennas for "green" Electronics

Optimisation Design For Eeprom Embedded In Uhf-Rfid Passive Transponders

Compaction Uniformity and Environmental Adaptability of Printed RFID Antenna

Proposed Methodology for End-of-Life Option using Multi Criteria Decision Analysis: A Study for General Paper Product

Disassembly planning and sequencing for end-of-life products with RFID enriched information

Importance of Computational Electromagnetic Modeling in the Development of RFID Tags for Paper Reel Identification

Design and Analysis of Analog Front-End of Passive RFID Transponders