A Study on Electrical-Chemistry for the Flotation in the Ultra-Fine Pt-Pd Ore

Wenbin Zhang

2010-01-01

Abstract:It had been done to regulate the pulp by chemical reagent,which can help to reduce the velocity of oxidization in the surface of the ore.OC was the reagent to be made by ourselvs,the natural pH was had been selected to flotation,and the reasonable dosage for sodium sulphide had been found to improve the flotation for middlings.

What problem does this paper attempt to address?

Recovery of Phosphorite from Coarse Particle Magnetic Ore by Flotation

Shi Shuaixing,Zhang Ming,Tan Ming,Lai Maohe

DOI: https://doi.org/10.1016/j.minpro.2015.04.021

2015-01-01

International Journal of Mineral Processing

Abstract:Chengde area in China is rich in magnetite resources containing phosphorus. It is meaningful to comprehensively recover phosphorus from the tailings of magnetic separation by flotation. However, the phosphorite particles are severely coarse with only 25% particles in size of −0.074mm approximately and over 50% particles in size of +0.25mm. The coarse particle settlement in conventional flotation cell usually appeared when the minerals are processed by flotation. In order to solve particle settling problem, JJF flotation cell is specially optimized to strengthen suspension capacity and circulation capacity for coarse particles, and the industrial experiment was carried out to recover phosphorite from the tailings of magnetite separation with 160m3 optimized JJF flotation cell. The industrial experiment results prove good adaptability of the optimized 160m3 flotation cell for coarse particles. When the feed grade of P2O5 is 2.12%, the concentrate grade is up to 30.68%, tailing grade is 1.14%, recovery is 47.97% and the yield of concentrate is 3.35%. Good metallurgical performances are achieved. The comprehensive utilization of phosphorus resources could be significantly improved in this area in the future.
Exploiting the Influence of Oxidization on Ultra-Fine Copper and Nickel Sulfide Containing Pt-Pd in Yunnan Mine

Min Tang,Bao Liang Ge,Shu Ming Wen

DOI: https://doi.org/10.4028/www.scientific.net/amr.712-715.760

2013-06-01

Advanced Materials Research

Abstract:It is known that oxidation is one of the most common ways for penlandite to be introducted into tailing during traditional coarse-particle sulfide flotation. However, it could become much more complicated and challenging problems for the low-grade, fine-disseminated Cu-Ni sulfides containing Pt and Pd in Yunnan Mine, accompanied with more than 75% of the content of MgO in the ore sample is. Direct flotation tests had been conducted to extract the metallic values as much as possible by adding traditional depressants and collectors, such as carboxylmethyl cellulose, starch, sodium silicate, butyl xanthate, (BX), butyl ammonium dithophosphate (BA) and etc., the relatively satisfied recoveries of Cu, Ni, Pt and Pd in the concentrate from bench flotation tests were obtained, however, more than 30% of metallic values still lost in the slime. In this study, bench flotation tests for the ore sample fromYunnan Mine, micro-flotation tests of serpentines and pentlandite from Jinchuan Mine and their settling rate tests were conducted to figure out how the oxidation influence the recovery of the ultra-fine nickel sulfide. All the tests results pointed to the presence of over-oxidation on the ultra-fine nickel sulfide surface and lead to the loss of Ni containing Pt and Pd in the slime tailing. Some methods which tried to slow the speed of oxidation on mineral surface during grinding and flotation were introduced in order to recover the values before over-oxidation of sulfides; however, the slime coating of serpentines also may play an important role in disturbing the floatability of ultra-fine sulfide.
Study on Flotability and Surface Oxidation of Sulfide Minerals from the Tailing of an Iron-Copper Mine Using Electron Probe Microanalyzer

Yahui Zhang,Zhidong Tang,John Shirokoff

DOI: https://doi.org/10.1080/08827508.2019.1707675

2019-12-25

Mineral Processing and Extractive Metallurgy Review

Abstract:With the depletion of high-grade ores, beneficiation of valuable minerals from mineral processing tailings attracts attentions of mining companies and researchers. Recovery of valuable sulfide minerals by flotation from the tailing of an iron-copper mine in central China was investigated in this paper. The surface oxidation status of sulfide minerals is an important factor influencing their flotation properties. Electron probe microanalyzer (EPMA) equipped with wavelength dispersive X-ray spectrometer (WDS) is an effective apparatus for characterizing solid surface (interface), which can analyze the composition and element distribution on the surfaces of sulfide minerals so as to understand their oxidation status. EPMA-WDS was employed to analyze the phenomenon responsible for the low flotation recovery of chalcopyrite and pyrite in this tailing. The research methodology is a useful reference for further work in the field of sulfide mineral surface analysis.

metallurgy & metallurgical engineering,mining & mineral processing
Studies on the surface oxidation and its role in the flotation of mixed Cu-Ni sulfide ore

Dezhi Liu,Guofan Zhang,Jianxin Liu,Guangjiu Pan,Yanfei Chen,Mengtao Wang

DOI: https://doi.org/10.1016/j.powtec.2020.12.038

IF: 5.64

2021-03-01

Powder Technology

Abstract:<p>Surface oxidation has a significant influence on sulfides flotation. However, there is a little literature about the effect of surface oxidation in the flotation of mixed copper‑nickel sulfide (CuNi sulfide, mainly composed of pentlandite, chalcopyrite, pyrite and pyrrhotite). In this work, the effect of surface oxidation on the CuNi sulfide flotation was studied. Flotation results showed the surface oxidation had a stronger depression effect on CuNi sulfide flotation than that on the flotation of single pyrite and chalcopyrite mineral samples. XPS analysis results showed that the hydrophilic products sulfate and Fe/Ni oxide/hydroxide were generated on the oxidized CuNi sulfide surface, whereas no Cu oxide/hydroxide was found, indicating the occurrence of galvanic interaction, which might cause the stronger depression of oxidation on CuNi sulfide flotation. However, after the pretreatment of ultrasonic cleaning in HCl solution, the sulfate and iron hydroxide/oxide on CuNi sulfide surface decreased significantly, and then CuNi sulfide floatability was regained to some extent. Interestingly, adsorption results exhibited that the adsorption amounts of PBX on CuNi sulfide surface basically unchanged before and after oxidation, which might be caused by that chalcopyrite and pyrite were protected from oxidation as the cathode minerals in the galvanic interaction.</p>

engineering, chemical
Study on Recovery of Lead-Zinc Tailing Ore by Electrochemical Flotation

Gui Ying Zhou,Wen Juan Li,Yong Chen,Yong Sheng Song

DOI: https://doi.org/10.4028/www.scientific.net/amm.675-677.1451

2014-10-01

Applied Mechanics and Materials

Abstract:The tailing in a large lead-zinc-iron-sulfur multi-metallic mine has rich reservation in variety of metallic minerals. It has been difficult to recover because of all kinds of reasons. The challenges faced by lead-zinc ore beneficiation are, low grade and recovery of lead and zinc concentrate for fine disseminated grain size, high oxidation rate and close intergrowth. This paper presents a Pulp Potential Control Flotation by stages technique to improve the flotation performance of the lead-zinc ores. In the electrochemical potential controlling flotation processing, using DDTC as collector, the separation potential range of galena and sphalerite with pyrrhotite can be achieved. Flotation circuit of lead-zinc-silver tailing ore was achieved.
Flotation Separation of High Sulfur Lead-Zinc Ore

Zhi Tao Yuan,Xiao Long Yu,Li Ping Liu,Cheng Liang Wang

DOI: https://doi.org/10.4028/www.scientific.net/amr.454.205

2012-01-01

Advanced Materials Research

Abstract:According to the refractory lead-zinc ore properties with high pyrite, the experimental studies were conducted on floatation reagent conditions and closed circuit tests for comprehensive recovering of all types useful minerals. In comparison to the test results of different process flowsheets and different types of flotation reagents, adopting prior flotation lead (Pb)—Zn selective flotation (reagent removal and regrinding of rough concentrate)—S-selective flotation with Zn-tailings. The closed circuit tests were achieved: the grade of lead concentrate was 50.55% with a recovery of 92.25%; The grade of zinc concentrate was 40.12% with a recovery of 85.82%; The grade of sulfur was 48.58% with a recovery of 56.59%; The tailings grades of lead, zinc and sulfur were 0.27%, 0.31%, 3.90% respectively.
An Electrochemical Study of Surface Oxidation and Collectorless Flotation of Pyrite

Dongping Tao,Yue Wang,Lin Li,

DOI: https://doi.org/10.20964/2018.06.32

IF: 1.541

2018-06-01

International Journal of Electrochemical Science

Abstract:Pyrite is a common sulfide mineral and its surface oxidation and natural hydrophobicity play an important role in determining flotation performance for many minerals, particularly for sulfides and coal. In this study freshly fractured electrodes have been used to investigate the surface oxidation of fresh pyrite surface and collectorless microflotation tests were performed to study its natural hydrophobicity. Chronoamperometry performed on in-situ fractured electrodes demonstrated that pyrite oxidation takes place at potentials of -0.28 V (SHE) at pH 9.2 and 0 V at pH 4.6, considerably lower than previously assumed. Incipient oxidation at slightly more positive potentials produce a hydrophobic sulfur-rich species, most likely a polysulfide or metal-deficient sulfide, which imparts natural surface hydrophobicity to pyrite. Collectorless microflotation test results have indicated that pyrite acquires considerable floatability upon superficial oxidation. The collectorless flotation recovery of pyrite is determined by the relative amounts of polysulfide, soluble species, and insoluble species produced during oxidation, which depends on solution pH and potential.

electrochemistry
Flotation separation of chalcopyrite and pyrite via Fenton oxidation modification in a low alkaline acid mine drainage (AMD) system

Zhan Ding,Yunxiao Bi,Jie Li,Jiaqiao Yuan,Huixin Dai,Shaojun Bai

DOI: https://doi.org/10.1016/j.mineng.2022.107818

IF: 5.479

2022-09-01

Minerals Engineering

Abstract:The selective flotation separation of pyrite and chalcopyrite, and the comprehensive utilization of AMD play a vital role in the cleaner production of copper sulfide ore. In this paper, flotation separation of chalcopyrite and pyrite via Fenton oxidation modification in a low alkaline acid mine drainage (AMD) system was investigated. The results of micro-flotation experiment displayed that the maximum recovery difference between chalcopyrite and pyrite was 74.6% at recommended test conditions. The artificial mixed-mineral flotation experiment further confirmed the desirable flotation separation of minerals. Zeta potential, FTIR spectra analysis, contact angle measurement and adsorption amount analysis results confirmed that the hydrophilic species caused by Fenton oxidation could seriously hinder the interaction between pyrite surfaces and EX collector. Whereas, the Fenton oxidation had feeble influence on the floatability of chalcopyrite. The XPS study indicated that Fenton oxidation significantly increased the contents of SO42- on pyrite surfaces, and the concentration of SO42- increased from 5.9% to 37.65%. Meanwhile, this modification promoted the deep transformation of Fe chemical states mainly from Fe(II)-S to Fe(III)–OOH and Fe2(SO4)3. As a result, the contents of Fe(III)–OOH and Fe2(SO4)3 reached 50.04% and 29.19%, respectively. For chalcopyrite, a small amount of oxide/hydroxide species were formed during this processing, and the chalcopyrite can interact with EX collector effectively. Thus, flotation separation of chalcopyrite and pyrite via Fenton oxidation modification in a low alkaline AMD system mainly attributes to the significant differences in the number and species of hydrophilic species.

engineering, chemical,mining & mineral processing,mineralogy
Study on Flotation Technique of a Copper-lead-zinc Sulfide Ore in Xizang

刘安荣,唐云,陈福林

DOI: https://doi.org/10.3969/j.issn.0253-6099.2009.02.011

2009-01-01

Abstract:Integrated with ore properties,the effects of grinding fineness,collector agents and process flowsheet on the flotation of a copper-lead-zinc sulfide ore in Xizang were investigated,through which the processing parameters were determined.Adopting a closed-circuit flowsheet including one stage of roughing,one stage of cleaning and two stages of scavenging,with a grinding fineness of-0.074 mm range as around 67.00%,and using a combined collector of ethyl xanthate and diethyldithiocarbamate,a bulk concentrate with copper,lead and zinc grade of 13.81%,16.74% and 22.41% respectively,and the corresponding recovery of 95.47%,93.85% and 94.04%,respectively,was prepared.
Effect of regulating dissolved oxygen concentration in pulp with aerated gas on pyrite flotation

Ximei Luo,Wen Yang,Shuming Wen,Qiqiang Lin,Dayong Wei,Chao Li,Ying Zhang,Zhenguo Song,Yunfan Wang

DOI: https://doi.org/10.1016/j.mineng.2023.108290

IF: 5.479

2023-08-10

Minerals Engineering

Abstract:Moderate oxidation is beneficial to the flotation of sulfide ores, but the exact dissolved oxygen (DO) concentration suitable for flotation is still unclear. In this work, a self–made vacuum aeration flotation equipment was designed and assembled to accurately control the DO concentration in pulp by adjusting the relative proportion of O 2 /N 2 during aeration, and the effect of DO concentration on the floatability and surface properties of pyrite as well as the interaction between pyrite and xanthate was studied. Microflotation experiments, contact angle, time–of–flight secondary ion mass spectrometry, X–ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, electrochemical and localized electrochemical impedance spectroscopy measurements were conducted in this investigation. The results showed that the flotation recovery of pyrite could be remarkably affected by DO concentration in pulp; it increased first and then decreased with the increase of DO concentration; an optimal DO concentration (DO = 3.3 mg/L) was helpful for pyrite flotation recovery; both the formation of dixanthogen and the avoidance of excessive iron oxide/hydroxide formed on pyrite surface were the key to improve the pyrite recovery. This research is expected to be applied in optimizing the flotation separation by DO-pH combined detection and regulation, strengthening the green flotation of sulfide ore with low collectors, and the design and manufacture of new closed and efficient sulfide ore flotation equipment.

engineering, chemical,mining & mineral processing,mineralogy
Understanding the Roles of Polyethylene Oxide and Xanthate in Reducing Quartz Gangue Entrainment in Sulfide Ore Flotation

M. Ourriban,Weikang Liu,Qi Liu,Jihua Gong,Yongjun Peng,Ahmed Bouajila

2010-01-01

Abstract:Photometric dispersion analysis (PDA), scanning electron microscope (SEM) and zeta potential measurements were used to study the roles of polyethylene oxide (PEO) and xanthate in sulfide flotation. When a high molecular weight PEO was added to a sulfide flotation pulp, it flocculated both sulfide and non-sulfide minerals to form large heteroaggregates. However, with subsequent addition of xanthate, the sulfide mineral particles broke away from the aggregates. This led to the disintegration of the large hetero-aggregates and the formation of smaller and separate homo-aggregates of sulfide and non-sulfide minerals. This process can be utilized to lower the hydraulic entrainment of ultrafine gangue minerals in sulfide ore flotation.
A case study of flotation of chalcopyrite-molybdenite ore using a mixture of pyrogallic acid and o-isopropyl ethylthiocarbamate: Insights from ab initio calculations

Yuanjia Luo,Leming Ou,Wei Sun,Haisheng Han,Jianhua Chen,Jian Peng

DOI: https://doi.org/10.1016/j.apt.2023.104039

IF: 4.969

2023-06-01

Advanced Powder Technology

Abstract:To date, lime-free flotation processes are increasingly advocated due to many problems caused by the traditional process using lime (CaO) as a depressant and xanthate (BX) as a collector. In this work, we developed a combination of pyrogallic acid (PGA) and o-isopropyl ethylthiocarbamate (Z200) as an eco-friendly alternative to the lime-xanthate process for chalcopyrite-molybdenite (ccp-mlb) flotation. Roughing flotation experiments showed that this process yields ccp-mlb concentrate with similar recovery and grade of Cu and Mo as in the traditional lime-xanthate process. However, the huge advantage of the novel process is that it requires ten times lower dosages of sodium sulfide in the subsequent separation of ccp-mlb concentrate. The ab initio calculations explained this trend at the atomistic level, where hydrogen sulfide ions could desorb collector more easily from the Z200@ccp complex compared with BX@ccp. The same method could be applied for environmentally friendly separations of other resources with similar composition.

engineering, chemical
Study on Flotation of a Refractory Copper-zinc Polymetallic Sulfide Ore

Sun Yun-li

Abstract:A refractory copper-zinc polymetallic sulfide ore in China has the characteristics of close symbiosis,high content of secondary copper sulfide,making the separation of copper and zinc difficult.According to this characteristics,adopting the combination of T9 and ZnSO4 as the inhibitor of zinc and Z-80 with strong selection and good selectivity as collector of copper,selective flotation experiment of inhibiting zinc and flotating copper was conducted,realizing the separation of copper and zinc.Through closed-circuit experiment the copper concentrate with the grade of 30.08% and the recovery of 92.98% and the zinc concentrate with the grade of 52.85% and the recovery of 84.89% were obtained respectively.The separation index is satisfactory.

Chemistry,Engineering,Materials Science
Importance of oxidation during regrinding of rougher flotation concentrates with a high content of sulfides

Xumeng Chen,David Seaman,Yongjun Peng,Dee Bradshaw

DOI: https://doi.org/10.1016/j.mineng.2014.04.014

IF: 5.479

2014-11-01

Minerals Engineering

Abstract:The objective of this study is to understand the flotation behavior of copper and gold minerals after regrinding the rougher flotation concentrate with a high pyrite content. It was found that low Eh and dissolved oxygen (DO) were produced after regrinding due to the quick consumption of oxygen by the large amount of fresh pyrite surfaces created, resulting in poor flotation of copper and gold and their selectivity against pyrite. A number of methods were used to provide an oxidizing condition, including pre-aeration before flotation, regrinding in an oxidizing condition, and addition of different oxidizing agents during regrinding. It was found that all the oxidizing methods improved the flotation of copper and gold, however, the effectiveness of these methods varied from case to case. This study demonstrates the importance of oxidation during or after regrinding for the flotation of rougher flotation concentrates with high sulfide contents.

engineering, chemical,mining & mineral processing,mineralogy
Prospects of pulp aeration for the cleaner production of pyrrhotite-rich type copper sulfide ore: Mechanism and application

Changtao Wang,Runqing Liu,Qilin Zhai,Wenchao Dong,Zhenhui Xie,Wei Sun,Wenjihao Hu

DOI: https://doi.org/10.1016/j.jclepro.2023.136921

IF: 11.1

2023-03-28

Journal of Cleaner Production

Abstract:Mineral extraction is facing increasingly severe challenges in terms of environment protection and cost reduction. Abundant of lime and sulfuric acid were consumed in the traditional high alkaline process (HAP) to extract chalcopyrite and iron sulfides. In this study, pulp aeration process (PAP) was proved a low-cost and environment friendly method in the processing of a pyrrhotite-rich type copper sulfide ore. Flotation results confirmed that pulp aeration was able to selectively depress pyrrhotite and pyrite flotation under ML8 system, thus 3000 g/t lime was cancelled during copper flotation stage, and around 4000 g/t sulfuric acid was saved during the subsequent sulfur flotation stage due to the low initial pulp pH. In the novel PAP, the directly production cost decreased by 4.34 RMB/t, besides, approximately 3.6 kg carbon dioxide and other waste could be reduced indirectly. Mechanism research revealed that pulp aeration oxidized the surface of pyrrhotite and pyrite, which further depressed the subsequent ML8 adsorption. However, the adsorption of ML8 on chalcopyrite was stable enough and it was unaffected by pulp aeration. Overall, pulp aeration was an environment friendly and cost-effective method for the separation of high-pyrrhotite type copper sulfide ore, which possessed broad industrial application prospects.

environmental sciences,green & sustainable science & technology,engineering, environmental
Flotation of Copper Sulfide Ore Using Ultra-Low Dosage of Combined Collectors

Qing Geng,Guang Han,Shuming Wen

DOI: https://doi.org/10.3390/min14101026

IF: 2.5

2024-10-14

Minerals

Abstract:Copper sulfide ores frequently co-occur with pyrite, presenting a significant challenge for their selective separation during beneficiation processes. Despite advancements in flotation technology, there remains a critical need for efficient methods to enhance copper recovery while suppressing pyrite interference, particularly without compromising the associated precious metals such as gold and silver. Current practices often struggle with achieving high selectivity and recovery while maintaining environmental sustainability. Here, we investigate the efficacy of a ternary collector mixture consisting of ammonium dibutyl dithiophosphate (ADD), butyl xanthate (BX), and ethyl xanthate (EX) for the selective flotation of copper sulfide from a complex ore containing 0.79% Cu and associated precious metals (0.233 g/t Au and 5.83 g/t Ag). A combination of lime and hydrogen peroxide as inhibitors was employed to suppress pyrite effectively under alkaline conditions (pH = 11.33). The results demonstrate that the optimized ternary collector system (ADD:BX:EX at a ratio of 1:0.5:0.5) significantly improves the copper grade and recovery at an ultra-low dosage of 10 g/t. The optimized flotation method using the combined collectors and inhibitors effectively separated chalcopyrite from pyrite, achieving a copper concentrate with 20.08% Cu content and a recovery of 87.73%. Additionally, the process yielded notable recoveries of gold (9.22%) and silver (26.66%). These findings advance the field by providing a viable and environmentally conscious approach to the beneficiation of sulfide ores, potentially serving as a blueprint for processing similar mineral deposits while minimizing reagent usage and costs.

geochemistry & geophysics,mineralogy,mining & mineral processing
Research on Bulk Floatation Discarding Tailing of Copper and Zinc Polymetallic Sulfide Ores

P. Zhou,X. Tong,H. Xie,Q. Ye,Likun Gao,Ji Xing Liu

DOI: https://doi.org/10.4028/www.scientific.net/AMR.881-883.1621

2014-01-16

Abstract:This paper is aimed at a typical complex polymetallic copper-zinc sulfide ores in Yunnan province, China, and adopted the process of bulk floatation discarding tailing under coarse grinding condition, the influence factors are researched such as grinding fineness, types and dosage of flotation reagents. When the coarse grinding size-74μm 75% and butyl xanthate and ethyl xanthate as combination collector, The amount of flotation discarding tailing is 60% for crude ores, the tailings contain 0.058% Cu, 0.027% Pb and 0.12% Zn, the loss rate of various metals in tailing is 3.21% Cu, 5.49% of Pb and 3.35% of Zn. This research has referenced significance to economical development and utilization of copper-zinc sulfide ore resources.

Chemistry,Engineering,Materials Science
Enhancing flotation separation of fine copper oxide from silica by microbubble assisted hydrophobic aggregation

Qiurong Long,Hao Wang,Feng Jiang,Wen Tan,Jinghe Chen,Shuiping Zhong,Xianjian Guo,Qiankun Wang,Zhenghe Xu

DOI: https://doi.org/10.1016/j.mineng.2022.107863

IF: 5.479

2022-10-19

Minerals Engineering

Abstract:One of the main challenges facing the flotation of base metal oxide minerals is their fine sizes of particles as a result of fine grinding to achieve a desired degree of liberation for low-grade and finely disseminated complex ores. This study aims at studying hydrophobic aggregation and in situ gas nucleation of fine copper oxides with sodium dodecyl sulfate (SDS) as a selective collector to enhance CuO recovery. Experimental results by in situ and real time particle size measurement using focused beam reflectance measurement (FBRM) coupled with particle vision measurement (PVM) showed an enhanced aggregation of fine CuO by SDS adsorption. Particle aggregation assisted by gas nuclei which were generated in situ on CuO by high intensity agitation (HIA) was visualized by total internal reflection fluorescence microscopy (TIRFM). It is the enhanced aggregation with nanobubbles as bridges that improved its recovery from fine silica. Coupled with the calculation using the extended DLVO theory, contact angle and zeta potential of fine particles were measured to understand the critical role of hydrophobic forces in aggregation of fine CuO particles. The copper ions dissolved from the fine copper oxide were found to inadvertently activate fine silica flotation which could be effectively depressed by ethylene diamine tetraacetic acid (EDTA). A combination of SDS with EDTA was proposed and demonstrated to achieve selective recovery of fine copper oxide from fine silica gangue. The results from this study provide directions for enhancing copper recovery from low grade and finely disseminated copper oxidize ores, in particular from tenorite ores.

engineering, chemical,mining & mineral processing,mineralogy
Experimental Study on Activated Sulfur Selection from High Alkalinity Lead Zinc Flotation Tailings

Tengyue Gao,Guangsheng Li,Xingfu Zhu,Qiang Ji,A.-S. Nizami,Z.B. Daud

DOI: https://doi.org/10.1051/e3sconf/202452002018

2024-05-03

E3S Web of Conferences

Abstract:This article takes the flotation tailings of a high sulfur lead-zinc mine in Inner Mongolia as the research object. XRD and BPMA automatic process mineralogical analysis systems are used to analyze the mineral composition of the tailings, and experimental research is conducted on the comprehensive recovery of pyrite through activated flotation. The results showed that using concentrated sulfuric acid as an activator, ethyl xanthate and isoamyl xanthate as a combination collector, and adopting a flotation process of "one coarse, one sweep, and two fine", a concentrate product with a yield of 9.31% and a sulfur grade of 37.78% can be obtained, and the sulfur recovery rate in the concentrate can reach 77.13%; The comprehensive recovery and utilization of sulfur in the original flotation tailings have been achieved.

A Study on Electrical-Chemistry for the Flotation in the Ultra-Fine Pt-Pd Ore

Recovery of Phosphorite from Coarse Particle Magnetic Ore by Flotation

Exploiting the Influence of Oxidization on Ultra-Fine Copper and Nickel Sulfide Containing Pt-Pd in Yunnan Mine

Study on Flotability and Surface Oxidation of Sulfide Minerals from the Tailing of an Iron-Copper Mine Using Electron Probe Microanalyzer

Studies on the surface oxidation and its role in the flotation of mixed Cu-Ni sulfide ore

Study on Recovery of Lead-Zinc Tailing Ore by Electrochemical Flotation

Flotation Separation of High Sulfur Lead-Zinc Ore

An Electrochemical Study of Surface Oxidation and Collectorless Flotation of Pyrite

Flotation separation of chalcopyrite and pyrite via Fenton oxidation modification in a low alkaline acid mine drainage (AMD) system

Study on Flotation Technique of a Copper-lead-zinc Sulfide Ore in Xizang

Effect of regulating dissolved oxygen concentration in pulp with aerated gas on pyrite flotation

Understanding the Roles of Polyethylene Oxide and Xanthate in Reducing Quartz Gangue Entrainment in Sulfide Ore Flotation

A case study of flotation of chalcopyrite-molybdenite ore using a mixture of pyrogallic acid and o-isopropyl ethylthiocarbamate: Insights from ab initio calculations

Study on Flotation of a Refractory Copper-zinc Polymetallic Sulfide Ore

Importance of oxidation during regrinding of rougher flotation concentrates with a high content of sulfides

Prospects of pulp aeration for the cleaner production of pyrrhotite-rich type copper sulfide ore: Mechanism and application

Flotation of Copper Sulfide Ore Using Ultra-Low Dosage of Combined Collectors

Research on Bulk Floatation Discarding Tailing of Copper and Zinc Polymetallic Sulfide Ores

Enhancing flotation separation of fine copper oxide from silica by microbubble assisted hydrophobic aggregation

Experimental Study on Activated Sulfur Selection from High Alkalinity Lead Zinc Flotation Tailings