Abstract:In order to realize the utilization of coal-fired solid waste and captured carbon dioxide, the effects of ratio of solid waste, mineralized curing pressure and mineralized curing temperature on the compressive strength and carbon fixation rate of aerated concrete were studied, with the coal-based waste, coal ash and desulfurization gypsum as the main raw materials and slag as the supplementary cementitious material. The crystal phase structure and micro morphology under different mineralized curing conditions were analyzed by XRD and SEM, and the effect of different mineralized curing conditions on the pore structure of aerated concrete was studied by MIP. The experimental results show that the appropriate residual water/slag ratio is helpful to improve the CO 2 fixation rate and early compressive strength of aerated concrete. When the CO 2 curing pressure increases from 0.05 MPa to 1.00 MPa, the carbon fixation rate increases by 24.8%, and the compressive strength increases first and then decreases. When the curing pressure is 0.1 MPa, the maximum compressive strength is reached. With the CO 2 curing temperature rising from 25 ℃ to 105 ℃, the carbon fixation rate and compressive strength increases first and then decreases. The carbon fixation rate reaches maximum of 7.21% at 45 ℃, and the compressive strength reaches maximum of 3.53 MPa at 65 ℃. According to analysis of XRD and SEM, the major mineralized products are CaCO 3 , which mainly exist in the form of calcite and vaterite. Higher curing pressure（≥0.2 MPa） is likely to cause micro-cracks at the product interface. With the increase of curing temperature, the mineralized products and hydrated products appear simultaneously. According to MIP analysis, the influence of mineralized curing on the pores of aerated concrete can be divided into two aspects: on the one hand, CaCO 3 and other products with small particle size can fill the pores of 10-50 nm, on the other hand, reaction heat of mineralization and volumetric expansion of products can cause the increase of 30-60 μm pores. The microstructure can be optimized by increasing the curing temperature, which can make the distribution of pores more uniform.

Experimental Research on Aerated Concrete Preparation with Low-Silicon Tailings of Copper Mine

Development of Sustainable Self-Compacting Concrete Using Recycled Concrete Aggregate and Fly Ash, Slag, Silica Fume

Mechanical and Durability Properties of Sustainable Self-Compacting Concrete with Recycled Concrete Aggregate and Fly Ash, Slag and Silica Fume

Carbonation Curing of Industrial Solid Waste‐based Aerated Concretes

Experimental Research On Solidification Of Ningbo Soil With Its Different Initial Status

Experimental Study of Making Aerated Concrete Block by Iron Tailings

Experimental Study on the Concrete with Compound Admixture of Iron Tailings and Slag Powder under Low Cement Clinker System

Synthesis and influencing factors of high-performance concrete based on copper tailings for efficient solidification of heavy metals

A Feasibility Study of Low Cement Content Foamed Concrete Using High Volume of Waste Lime Mud and Fly Ash for Road Embankment

Experimental study on strength and abrasion-resistance enhancement admixture

Utilizing Ceramic Waste for Autoclaved Aerated Concrete

Study on the preparation and performances analysis of lightweight high strength ceramsite aerated concrete

Preparation of Cementitious Materials from Mechanochemically Modified Copper Smelting Slag Compounded with High-Aluminum Fly Ash

Experimental Research on Soiled-based Foamed Concrete

Study on Preparation and Performance of Brick-concrete Recycled Sand Powder Autoclaved Aerated Concrete

Mechanical Properties and Hydration Mechanism of Iron Tailings–Cement-Based Supplementary Cementitious Materials

Effect of Cementitious Material Composition on the Performance of Low-Carbon Foamed Lightweight Soil

Experimental Investigation into the Proportion of Cemented Aeolian Sand-Coal Gangue-Fly Ash Backfill on Mechanical and Rheological Properties

Effect of Iron Tailings and Slag Powders on Workability and Mechanical Properties of Concrete

Test research on the effects of mechanochemically activated iron tailings on the compressive strength of concrete

Study on formulation of aerated concrete by CO2 mineralization using coal ash