Abstract:Due to the small neutron absorption cross section and excellent thermal creep performance, zirconium alloy is one of the most important cladding materials for fuel rods in commercial fission reactors. However, quantitative analysis of the effects of temperature and grain boundaries on the corrosion microstructure evolution of zirconium alloys is still needed. The establishing of a phase field simulation for the corrosion process of polycrystalline zirconium alloy and the systematical investigating of the thermodynamic influence are both very important. In this study, the phase field model of the corrosion process in zirconium alloys is developed by combining corrosion electrochemistry through calculating the interfacial energy at the metal-oxide and oxide-fluid boundaries. Then the model is used to investigate the uniform corrosion behavior on the surface of Zr-2.5Sn alloy, which demonstrates that the corrosion kinetic curve follows a cubic rule. Subsequently, the influence of temperature on the corrosion thickening curve of zirconium alloy is examined, and good agreement between simulation and experimental results is achieved. It is observed that during early stage of oxide layer formation, there is a high growth rate with minimal temperature dependence; however, as the oxide layer thickness increases, temperature becomes a significant factor affecting its growth rate, with higher temperatures resulting in faster corrosion rates. Furthermore, the effect of polycrystalline zirconium alloy matrices on corrosion rate is investigated, revealing that the grain boundaries accelerate oxide layer thickening due to enhanced oxygen diffusion rates. At metal-oxide interface, O2- bands are formed in areas with higher O2- concentration along these grain boundaries towards the metal matrix, which mainly influences oxidationcorrosion rate during the initial oxidation stage.

The Role of Secondary Phase Precipitates in Zircaloy Corrosion: from Point Defects to Local Percolation

Effect of Nb and Cu on α/β Phase Transition Temperature and Corrosion Behavior of New Type Zirconium Alloys

Modelling amorphization and dissolution of Zr(Fe,Cr) 2 secondary phase precipitates in Zircaloys

From Microstructural Changes to Electrochemical Behavior: Decoding the Corrosion Mechanism in Zr-Sn-Nb-Fe-Cr-Mo-O-V Alloys

Initial localized corrosion induced by multiscale precipitates in the new generation high-strength Al-Zn-Mg-Cu alloy

Phase-field Simulation of High-Temperature Corrosion of Binary Zr-2.5Sn Alloy

Unraveling Different Influences of the Fraction of the Tetragonal Phase in Oxide Films on the Corrosion Resistance of Zr Alloys from the Phase Transition Mechanism

On Corrosion of Zirconium Alloy in Dissolved Oxygen Water：The Role of Cu Addition

3D reconstruction and interconnectivity quantification of the nano-porosity in the oxide layer of corroded Zr alloys

Electrochemical Properties of the Passive Film on Bulk Zr–Fe–Cr Intermetallic Fabricated by Spark Plasma Sintering

On corrosion of zirconium alloy in dissolved oxygen water: The role of Cu addition

Effect of Microstructure on Corrosion Behavior of A Zr-Sn-Nb-Fe-Cu-O Alloy

Effects of Precipitation on the Stress Corrosion Crack Initiation of Alloy 718 in Simulated Pressurized Water Reactor Primary Environment

Unraveling different influences of the fraction of tetragonal phase in oxide film on corrosion resistance of Zr alloys from phase transition mechanism

Unveiling Corrosion Pathways of Sn Nanocrystals through High-Resolution Liquid Cell Electron Microscopy

Nano-porosity effects on corrosion rate of Zr alloys using nanoscale microscopy coupled to machine learning

Phase-field investigation of intergranular corrosion mechanism and kinetics in aluminum alloys

Role of second phases on the corrosion resistance of Mg-Nd-Zr alloys

Homogenization and Growth Behavior of Second-Phase Particles in a Deformed Zr–Sn–Nb–Fe–Cu–Si–O Alloy

Understanding Corrosion Mechanism of Sn–Zn Alloys in NaCl Solution Via Corrosion Products Characterization

The Effect of Secondary Phase on Corrosion Behaviors of the Titanium–zirconium–molybdenum Alloy