Abstract:In this work, a low-noise and high-rate front-end readout application-specific integrated circuit (ASIC) named SECALROC2 for the electromagnetic calorimeter (ECAL) in the super tau-charm factory (STCF) is presented. The chip is designed to process signals generated from avalanche photodiode detectors (APDs) for both energy and time measurement. The large detector capacitance and leakage current of the APD pose a great challenge to the noise and speed performance of the front-end readout circuit (ROC). A low-noise preamplifier and a fifth-order high-linearity shaper with adjustable peaking times are proposed to decrease noise induced by the 270-pF detector capacitance. A peak detect-and-hold circuit and a high-linearity differential analog buffer are adopted to convert each peak voltage of the shaper to differential voltages with sufficient driving capability. A fast shaper and a discriminator are implemented to produce trigger signals for the time of arrival (TOA) measurement. To reduce the complexity and power consumption of the ECAL system, a 12-bit 10-MS/s pipelined analog-to-digital converter (ADC) and a 16-bit three-stage time-to-digital converter (TDC) with 42-ps bin size TDC are integrated on-chip for full-digitalized outputs. This ASIC was designed and fabricated in a standard commercial 1P6M 0.18-mu m mixed-signal CMOS process and the chip area occupancy is 2.4 x 1.6 mm(2). The experimental results show that the input charge of the ASIC ranges from 3.2 to 400 fC. The measured nonlinear error of the system is less than 2.5% with an event rate up to 400 kcps. The equivalent noise charge (ENC) is 1367 e(-) + 4.93 e(-)/pF at 800-ns peaking time. The timing resolution is better than 540 ps at an input charge of 160 fC. The measured ENC can achieve 3820 e(-) when the ASIC is connected to an APD detector. The effective number of bits (ENOB) of the ADC is 10.8-bit when operated at 10 MS/s.

Development of Front-End Readout Electronics for Silicon Strip Detectors

Design and Characterization of a Low-Noise Front-End Readout ASIC in 0.18- $\mu$ M CMOS Technology for CZT/Si-PIN Detectors

Design and preliminary performance of a novel mixed-signal front-end electronics with post digital shaping for CZT detectors

Design of a Low-Power Front-End Readout ASIC Based on Energy-Efficient Amplifiers, Featured 126 e-(rms), 0.6 mW/Channel for Si-PIN Detectors

Design and Development of a Front-End Readout ASIC for APD-Based STCF Electromagnetic Calorimeter

SENSROC12: A Four-Channel Binary-Output Front-End Readout ASIC for Si-PIN-Based Personal Dosimeters

Design and Performance of a 16-Channel Radiation-Hardened Low-Noise Front-End Readout ASIC for CZT-based Hard X-ray Imager

Design and Performances of A Low-Noise and Radiation-Hardened Readout Asic for Cdznte Detectors

The Design of a Fast Front-end Readout ASIC for Time Correction with Low Voltage

SENSROC12V4: a Low Noise Programmable Readout ASIC for Si-PIN Detectors

Design of a Low-Noise Photon-Count Readout ASIC for Si-PIN-Based Personal Dosimeters with Low Energy Detection Threshold

Design and Characteristics of a Multichannel Front-End ASIC Using Current-Mode CSA for Small-Animal PET Imaging.

Data Acquisition System for CEPC Vertex Detector Prototype

SECALROC2: A Low-Noise, High-Speed, and Full Digital Outputs Front-End ASIC for STCF Electromagnetic Calorimeter With APD Detectors

A Low Noise Front-End Readout ASIC for CdZnTe Detector

Design and Test Results of a Front-End ASIC for Radiation Detectors

Development of a compact radiation-hardened low-noise front-end readout ASIC for CZT-based hard X-ray imager

A Low-Noise 64-Channel Front-End Readout ASIC for CdZnTe Detectors Aimed to Hard X-ray Imaging Systems

Development Of A Multi-Energy Photon-Counting Readout Asic For Czt Detectors

Design of Multi-channel Front-end Readout Electronics Applied for New Plastic Scintillator Array Detector

Front-end ASIC for spectroscopic readout of virtual Frisch-grid CZT bar sensors