Abstract:This study introduces a current sensing approach for battery monitoring and protection applications, using a low‐side shunt and an adjustable range. To address the challenge posed by the extremely low resistance of the shunt, a preamplifier is used to amplify the small voltage signal across the shunt. The current sensing process incorporates chopper techniques, a current‐feedback instrumentation amplifier, and mismatch optimization methods to effectively minimize sensing errors. In addition to these methods, the conversion of current into digital form is facilitated by an analogue‐to‐digital converter. Trimming correction is used to mitigate the remaining errors. The current sensing circuit is realized using a 0.18 μm high voltage 100 V bipolar‐CMOS‐DMOS process. Remarkably, this circuit exhibits a gain error of ±0.55% across a range of ±24 A, spanning temperatures from −40°C to 85°C. Operating from a 5‐V LDO supply, it maintains an average current consumption of 12.9 μA while occupying an active area of 0.34 mm2. This study introduces a current‐sensing approach for battery monitoring and protection applications, using a low‐side shunt and an adjustable range. To address the challenge posed by the meagre resistance of the shunt, a preamplifier is used to amplify the small voltage signal across the shunt. The current sensing process incorporates chopper techniques, a current feedback instrumentation amplifier, and mismatch optimization methods to minimize sensing errors effectively. In addition to these methods, the conversion of current into digital form is facilitated by an analogue‐to‐digital converter. Trimming correction is used to mitigate the remaining errors. The current sensing circuit is realized using a 0.18 μm high voltage 100 V bipolar‐CMOS‐DMOS process. Remarkably, this circuit exhibits a gain error of ±0.55% across a range of ±24 A, spanning temperatures from −40°C to 85°C. Operating from a 5‐V LDO supply, it maintains an average current consumption of 12.9 μA while occupying an active area of 0.34 mm2.

A High-precision Current Detection Circuit for Battery Management System.

A Power Management IC Used for Monitoring and Protection of Li-Ion Battery Packs

A current reference based on bandgap technology with wide input voltage range by using 0.18µm BCD process

A Front-End Circuit With 16-Channel 12-Bit 100-Ksps Rc-Hybrid Sar Adc For Industrial Monitoring Application

A High Precision Multi-Cell Battery Voltage Detecting Circuit for Battery Management Systems

A High-Voltage High-PSRR Power Management Circuit for BMS Chip of New Energy Vehicle

Design of Acquisition Front-end and Σ-ΔADC in Battery Management SoC

A High Accuracy and Wide Input Voltage Range Current Sense Amplifier for Bidirectional High-Side and Low-Side Current-Sensing

A power-efficient acquisition front end for the Li-ion battery management systems

Adjustable ±24‐A current monitoring for battery applications with ±0.55% gain error from −40°C to 85°C

A High Precision Voltage Reference Circuit for Battery Management System Chip of New Energy Electric Vehicle

BICMOS Residue Amplifier with Base Current Compensation Technique in High-speed Pipelined ADC

A Current-Sensing Circuit with High Accuracy and Fast Response

Real Time Zero Current Detection with Low Quiescent Current for Synchronous DC-DC Converter

Research and design of high accuracy high-side current sense amplifier

A 1.8 Μw 32 Nv/√hz Current-Reuse Capacitively-Coupled Instrumentation Amplifier for EEG Detection

A Low-Power Continuous-Time Delta-Sigma Analogue-to-Digital Converter for the Neural Network Architecture of Battery State Estimation

A 600 MHz-BW 154.3 Db-Fom Current-Mode Continuous-Time Pipelined ADC in 12 Nm CMOS

A 172.5Db-Fom Hybrid CT/DT Incremental Σ∆Modulator for Direct Current-to-Digital Conversion

A Highly Sensitive Wide-Range Weak Current Detection Circuit for Implantable Glucose Monitoring.

A PVT-Robust Transimpedance Amplifier for Ultra-Low Current Sensing