Abstract:Recently, the construction of stable superhydrophobicity on metallic wetting surfaces has gained increasing attention due to its potential wide applications. In this paper, we propose an economic fabricating method, which not only is suitable for metallic planar surfaces, but also could be applied onto cylindrical inner surfaces. It mainly involves two steps: etching micro-concaves by a movable mask electrochemical micromachining (EMM) technique and fabricating nanopillars of ZnO by a hydrothermal method. Then the influences of surface morphology on the static and dynamic behaviors of water droplets are investigated. The energy loss during impact on the surfaces is quantified in terms of the restitution coefficient for droplets bouncing off the surfaces. For hierarchical structures with excellent superhydrophobicity (contact angle :,approximate to 180 degrees and sliding angle <= 1 degrees), the droplet bounces off the surface several times, superior to the droplet's response on single nanopillars (contact angle :,approximate to 165.8 degrees and sliding angle :,approximate to 6.29 degrees) where droplet bounces off only for limited a number of times, and even far better than the dynamics of a liquid droplet impinging on microstructures (contact angle :,approximate to 132.1 degrees and sliding angle >90 degrees) where droplet does not rebound and remains pinned. The highest elasticity is obtained on the hierarchical surface, where the restitution coefficient can be as large as 0.94. The fabricating method is then applied onto the cylindrical inner surface and the wetting behavior is confirmed to be consistent with the planar surface. This method, which can be generalized to any kind of solid electroconductive metal or other surfaces with different shapes, could find wide practical applications in self-cleaning surfaces, chemical industry, microfluidic devices, mechanical engineering and aviation. (C) 2014 Elsevier B.V. All rights reserved.

Preparation of Superhydrophobic Cu Mesh and Its Application in Rolling-Spheronization Granulation

Fabrication of a Novel Superhydrophobic and Superoleophilic Surface by One-Step Electrodeposition Method for Continuous Oil/water Separation

Ultralow Adhesion and Phase Change Behaviors of Sulfur Droplets on the Superhydrophobic Surface and Its Application in the Granulation Process

Roll-to-Roll Manufacturing of Robust Superhydrophobic Coating on Metallic Engineering Materials

Manufacture of fine AL2O3 granules as catalyst carrier by an extrusion/spheronization method

Fabrication of Superhydrophobic Coatings by Low-Temperature Sintering of Ag Nanoparticle Paste

Fabrication and Characterization of Superhydrophobic Surface by Electroplating Regular Rough Micro-Structures of Metal Nickel

Fabrication of Hierarchical Structures for Stable Superhydrophobicity on Metallic Planar and Cylindrical Inner Surfaces

Large-Area Preparation of a Robust Superamphiphobic Coating for Chemical Mechanical Polishing Application

Packing the Silica Colloidal Crystal Beads: A Facile Route to Superhydrophobic Surfaces

Making Superhydrophobic Surfaces with Microstripe Array Structure by Diffusion Bonding and Their Applications in Magnetic Control Microdroplet Release Systems

Applicable Superamphiphobic Ni/Cu Surface with High Liquid Repellency Enabled by the Electrochemical-Deposited Dual-Scale Structure.

Construction of Mechanically Robust Superamphiphobic Surfaces on Fiber Using Large Particles

Preparation and Characterization of Super-Hydrophobic Silica Coating by HVOF

Adjusting droplet adhesion of superhydrophobic coating via surface embedding of microparticles with mixed shapes

Fabrication of Super Hydrophobic Surfaces on Copper by Solution-immersion

Superhydrophobic surfaces created by a one-step solution-immersion process and their drag-reduction effect on water

Fabrication of superhydrophobic surfaces with hierarchical structure and their corrosion resistance and self-cleaning properties

Preparation of superhydrophobic coatings with excellent mechanical and chemical stability by one-step spraying method with selected fluorine-free modifiers

Fabrication of Superamphiphobic Surface with Hierarchical Structures on Metal Substrate

A High-Efficiency Preparation Method of Super Wear-Resistant Superhydrophobic Surface with Hierarchical Structure Using Wire Electrical Discharge Machining