Abstract:A fully inkjet-printed strain sensor based on carbon nanotubes (CNTs) was fabricated in this study for microstrain and microcrack detection. Carbon nanotubes and silver films were used as the sensing layer and conductive layer, respectively. Inkjet-printed CNTs easily undergo agglomeration due to van der Waals forces between CNTs, resulting in uneven films. The uniformity of CNT film affects the electrical and mechanical properties. Multi-pass printing and pattern rotation provided precise quantities of sensing materials, enabling the realization of uniform CNT films and stable resistance. Three strain sensors printed eight-layer CNT film by unidirectional printing, rotated by 180° and 90° were compared. The low density on one side of eight-layer CNT film by unidirectional printing results in more disconnection and poor connectivity with the silver film, thereby, significantly increasing the resistance. For 180° rotation eight-layer strain sensors, lower sensitivity and smaller measured range were found because strain was applied to the uneven CNT film resulting in non-uniform strain distribution. Lower resistance and better strain sensitivity was obtained for eight-layer strain sensor with 90° rotation because of uniform film. Given the uniform surface morphology and saturated sheet resistance of the 20-layer CNT film, the strain performance of the 20-layer CNT strain sensor was also examined. Excluding the permanent destruction of the first strain, 0.76% and 1.05% responses were obtained for the 8- and 20-layer strain sensors under strain between 0% and 3128 με, respectively, which demonstrates the high reproducibility and recoverability of the sensor. The gauge factor (GF) of 20-layer strain sensor was found to be 2.77 under strain from 71 to 3128 με, which is higher than eight-layer strain sensor (GF = 1.93) due to the uniform surface morphology and stable resistance. The strain sensors exhibited a highly linear and reversible behavior under strain of 71 to 3128 με, so that the microstrain level could be clearly distinguished. The technology of the fully inkjet-printed CNT-based microstrain sensor provides high reproducibility, stability, and rapid hardness detection.

A Vacuum Sensor of Large Measurement Scale Based on Rubbing-Processed Carbon Nanotube Films

A vacuum sensor using field emitters made by multiwalled carbon nanotube yarns

Miniature vacuum sensor based on gas adsorptions from carbon nanotube field emitters

Micro-Pirani Pressure Sensor with Operation Range beyond Atmospheric Pressure based on Aligned Carbon Nanotube Films

Ultra-Sensitive and Wide Sensing-Range Flexible Pressure Sensors Based on the Carbon Nanotube Film/Stress-Induced Square Frustum Structure

Pressure sensing using vertically aligned carbon nanotubes on a flexible substrate

Ultrasensitive Airflow Sensors Based on Suspended Carbon Nanotube Networks

An ultra-sensitive and wide measuring range pressure sensor with paper-based CNT film/interdigitated structure

Vacuum Filtration-Coated Silver Electrodes Coupled with Stacked Conductive Multi-Walled Carbon Nanotubes/Mulberry Paper Sensing Layers for a Highly Sensitive and Wide-Range Flexible Pressure Sensor

Linearly Sensitive and Flexible Pressure Sensor Based on Porous Carbon Nanotube/Polydimethylsiloxane Composite Structure

A Flexible and Highly Sensitive Piezoresistive Pressure Sensor Based on Micropatterned Films Coated with Carbon Nanotubes

A Fully Inkjet-Printed Strain Sensor Based on Carbon Nanotubes

A Cylindrical Triode Ultrahigh Vacuum Ionization Gauge with a Carbon Nanotube Cathode

Flexible Capacitive Pressure Sensor Based on Multi-Walled Carbon Nanotube Electrodes

An Intelligent Tactile Sensor Based on Interlocked Carbon Nanotube Array for Ultrasensitive Physiological Signal Detection and Real‐Time Monitoring

Toward Practical Gas Sensing with Rapid Recovery Semiconducting Carbon Nanotube Film Sensors

Flexible Gas Sensors Based on Carbon Nanotube Hybrid Films: A Review

Preparation and Force-Sensitive Properties of Carbon Nanotube/Polydimethylsiloxane Composites Films

Vacuum Measurement Based on Field Emission of CNT Yarn

An On-Chip Nanoscale Vacuum Sensor Based on Electroformed Silicon Oxide

A Flexible NO2 Gas Sensor Based on Single-Wall Carbon Nanotube Films Doped with a High Level of Nitrogen