Analysis on Remote Distance Measurement Accuracy with Intermediate Method of Electronic Total Station

Yan Yu

2011-01-01

Abstract:This paper mainly introduces the working principle and thinking of remote distance measurement with intermediate method of electronic total station,analyzes its measuring accuracy,and proposes proposals for improving measurement schedule in actual measurement,with a view to improve measurement efficiency.

What problem does this paper attempt to address?

Study on Improving GPS Measurement Accuracy

HH Yu,Y He,XF Ge

DOI: https://doi.org/10.1109/imtc.2005.1604396

2005-01-01

Abstract:By analyzing a number of GPS data, a principle was found that GPS single point location data was composed of position excursion and normal distribution. In order to separate the position excursion from normal distribution, normality elimination method was advanced. First, calculated average latitude and longitude coordinate of GPS data as central coordinate of normal distribution. Then, calculated confidence interval [-sigma, sigma] and removed excursion points outside of it. Finally, calculate a radius of the circle that ensure 70~80% points falling in the circle, namely defined threshold lambda as 0.7~0.8. By reason that the property of 70~80% points was able to take the place of all points, the method could be feasible and the result was obvious. Aimed at the location error of GPS single point measurement was large, a new method of two points relative location measurement was put forward which used two GPS receivers to acquire location data separately and simultaneously at two endpoints of a certain distance. The experiment results indicated that when threshold lambda was 0.7, the previous measurement error of single point location experiment was above 10m. However, after using the new method, the location error was about 1.2m. It was turned out that the latter improved measurement accuracy greatly
Dynamic measurement technology based on dual electronic total stations and its application

Li Junqiao,Tang Jun,Fu Jialiang,Zhou Wenbo,Zhang Yong

DOI: https://doi.org/10.19650/j.cnki.cjsi.2012.10.027

2012-01-01

Abstract:A target ranging model based on dual electronic total stations is proposed in this paper. Two techniques of coordinate transformation based on quadrangle method and triangulation method are firstly introduced. The influence of time synchronization error is reduced by using quasi-synchronous technique based on interpolation alignment. The error model of dynamic ranging based on dual electronic total stations is established; the simulation theoretical error is calculated and dynamic accuracy test is carried out. The test results in the laboratory show that the dynamic measurement accuracy based on dual electronic total stations reaches to 5 mm when the velocity of the platform is under 0.5 m/s. Finally, an application example of coordinate calibration for sonar transducer array of underwater acoustic positioning system based on the proposed method is presented.
Integrated Method for Measuring Distance and Time Difference Between Small Satellites

Zhu Yaowei,Xu Zhaobin,Jin Xiaojun,Guo Xiaoxu,Jin Zhonghe

DOI: https://doi.org/10.23919/jsee.2021.000051

IF: 1.363

2021-01-01

Journal of Systems Engineering and Electronics

Abstract:The advancement of small satellites is promoting the development of distributed satellite systems, and for the latter, it is essential to coordinate the spatial and temporal relations between mutually visible satellites. By now, dual one-way ranging (DOWR) and two-way time transfer (TWTT) are generally integrated in the same software and hardware system to meet the limitations of small satellites in terms of size, weight and power (SWaP) consumption. However, studies show that pseudo-noise regenerative ranging (PNRR) performs better than DOWR if some advanced implementation technologies are employed. Besides, PNRR has no requirement on time synchronization. To apply PNRR to small satellites, and meanwhile, meet the demand for time difference measurement, we propose the round-way time difference measurement, which can be combined with PNRR to form a new integrated system without exceeding the limits of SWaP. The new integrated system can provide distributed small satellite systems with on-orbit high-accuracy and high-precision distance measurement and time difference measurement in real time. Experimental results show that the precision of ranging is about 1.94 cm, and that of time difference measurement is about 78.4 ps, at the signal to noise ratio of 80 dBHz.
Study on Remote Monitoring System of 3D Scanning and Measuring Machine

Wang Wen,Lu Keqing,Chen Zichen

2006-01-01

Abstract:Combing with remote monitoring and control technology with production management ideas, a remote monitoring and management system of 3D laser scanning machine is presented in this paper. The operation model, system structure is studied and the theory to realize the system function is also given. With the net programming technology, the prototype system is successfully developed, furthermore, the key technologies were discussed. Finally the effect of the system is testified.
Research on Distance and Direction Correction of GPS and Total Station Measurements in the Jingzhou Section of Yangtse River

陈于,胡友健,陈刚,潘雄

DOI: https://doi.org/10.3969/j.issn.1672-4623.2010.02.016

2010-01-01

Abstract:This paper illustrates the course of distance and direction correction of GPS and Total Station measurements in the evolvement monitoring of Jingzhou section of Yangtse River.This can be often ignored in the engineering survey,and thus some data can't be handled correctly,and this may cause person to doubt observation precision is not enough,or need to be re-measurement,which gives the progress of the project a negative impact.This paper illustrates the specific methods and process correction of distance and direction,and after the correction computation,the outcome can meet the requirements of precision engineering.This shows that it is necessary to do distance and direction correction in long distance range.
On road section measurement and its data treatment

Q. Wang

Abstract:The paper introduces the basic principle of the measurement of the total station,analyzes the measurement accuracy,points out the effective section measurement method and the software system based on the total station can improve the data collection speed of the section along the expressways of mountainous areas,and can realize the digitalized work completely,and proves the method can enhance the quality and the efficiency of the road section measurement.

Computer Science,Engineering
Discussion on the Method of Precise REM

Gang Chen

2010-01-01

Abstract:With the rapid development of socio-economic,high-rise buildings are more and more.Accurately measuring the height of these buildings for the construction and safely monitoring to provide a reliable basis seem particularly important.Precise REM utang total station for two specific circumstances were discussed by many scholars with some improvement methods.This paper firstly describes the deficiencie and defects of these improved methods,and then proposed a new method of high-precision REM,and carried on the formula derivation and the analysis of accuracy,finally proved the feasibility and advantages of this method through two examples.
A Procedure for Constructing Virtual Digital Outcrop Models (vdom) and Its Application to Accuracy Comparison of Rock Discontinuity Geometric Parameters Based on Two Photogrammetric Methods

Jun Zheng,Wankun Li,Bohu Zhang,Qing Lü

DOI: https://doi.org/10.2139/ssrn.4148158

2022-01-01

SSRN Electronic Journal

Abstract:During the reconstruction of the digital outcrop models (DOM) by photogrammetry, the geodetic coordinate systems of the models can be calibrated through the camera positions or the control points. This paper developed a procedure for constructing virtual digital outcrop model and proposed a numerical simulation procedure of photogrammetry to compare the measurement accuracy of the described-above two methods. A physical model test indicated the validation of the proposed procedure. In addition, many numerical experiments about the accuracy of the camera positions and the control points are designed. The experiment results show that when the control point is used to reconstruct the DOMs, it is recommended to measure the coordinates of the control points by the device with high positioning accuracy, such as the total station or RTK equipment. If the device with high positioning accuracy is unavailable, better measurement accuracy can be obtained used the camera positions.
Design and Application of a High Precision Intelligent Distance Measuring Device

Xiaoxia Li,Qiaoni Zhao,Yongchao Xie

DOI: https://doi.org/10.1109/ICEITSA57468.2022.00071

2022-12-01

Abstract:With the rapid development of intelligent control technology, higher requirements for distance measurement accuracy are put forward in engineering practice. Ultrasonic is widely used in distance measurement because of its characteristics of long distance, low energy loss and low probability of interference. A high precision intelligent ranging device is designed in this paper. The practical application shows that the relative error of the distance measuring device is less than 0.4% in the range of (Om, 253m).

Engineering,Computer Science
APPLICATION OF LASER RANGING TECHOLOGY IN SLOPE ROMOTE MONITORING AND ERROR CORRECTION

DONG Chao,SUN Hong-yue,SHANG Yue-quan

DOI: https://doi.org/10.3969/j.issn.1001-6864.2011.01.038

2011-01-01

Abstract:Laser ranging is the technology which can use the the wireless data transfer module to complete the transfer of information of the slope monitoring automatically.Compared with the traditional monitoring instruments,laser ranging has some advantages in accuracy,timeliness and cost.Based on exploring the working principle of the laser ranging monitoring system,it has been applied in the 1# slope of a highway for a long-term monitoring.After a period time of working with total station together,it shows that the data by Laser ranging is favorable in precision and stability,and it also demonstrates that the laser ranging monitoring system is suit for long-term monitoring of slope.
Accuracy Comparison of Rock Discontinuity Geometric Parameters in Photogrammetry Based on Two Georeferencing Methods: Control Points and Geotagged Photos

Jun Zheng,Wankun Li,Bohu Zhang,Qing Lu

DOI: https://doi.org/10.1016/j.measurement.2022.111880

IF: 5.6

2022-01-01

Measurement

Abstract:During the reconstruction of the digital outcrop models (DOM) by photogrammetry, the geodetic coordinate systems of the models can be calibrated through the camera positions or the control points. This paper developed a procedure for constructing virtual digital outcrop model (VDOM) and proposed a numerical simulation pro-cedure of photogrammetry to compare the measurement accuracy of the mentioned-above two methods. A physical model test indicated the validation of the proposed procedure. In addition, many numerical experiments about the accuracy of the camera positions and the control points are designed. The experiment results show that when the control points are used to georeference the DOMs, it is recommended to measure the coordinates of the control points by the device with high positioning accuracy, such as the total station or RTK equipment. If the device with high positioning accuracy is unavailable, better measurement accuracy can be obtained using the camera positions.
Study on Quantitative Analysis Method of the Precision of Satellite Remote Sensing

XU Xue-ren,GONG Peng,YANG Bin,JIN Yong

DOI: https://doi.org/10.3969/j.issn.1000-3177.2007.02.004

2007-01-01

Abstract:The factors which influence the precision of satellite remote sensing have been analyzed firstly in this paper.Then a precision analysis model of satellite remote sensing was built using GIS.At last,the model has been validated with some test region data.The test result shows that the model is useable for quantitative analysis of the precision of satellite remote sensing plan.
Increase construction staking out efficiency with total station tachymeter

HUANG Zhi-qi

2007-01-01

Abstract:Combined with practical engineering of SL3 section of national main road from Shandan to Linze,the author introduces the measures of platform erection with free station positioning method,local conversion of coordinates,and accuracy evaluation of staking out in survey,and points out that man should use total station tachymeter with these methods to improve efficiency of survey and ensure its accuracy specification.
Remote value transmission and traceability technology of measuring instruments based on wireless communication

Lide Fang,Yiming Li,Sihan Duan,Kang Lan

DOI: https://doi.org/10.1063/5.0109480

2023-02-01

Abstract:When the traditional calibration methods of measurement instruments are applied, these measurement instruments need to be transmitted to a higher-level validation body for calibration. During transportation, many unknown factors will lead to additional errors that cannot be measured. Remote calibration effectively solves the problems of long calibration cycle and additional error generation. This Review summarizes research achievements made in the field of remote metrology. By comparing the existing remote calibration methods, their advantages and disadvantages are analyzed. Combined with the previous work of the research team, the application scenarios of the future remote value transmission and traceability technology are proposed.
A New Method of Laying-out Excavation Cutting with Total Stations

Jian-jun BAI,Wei-dong SONG

DOI: https://doi.org/10.3969/j.issn.1008-0562.2005.z1.017

2005-01-01

Abstract:Some functions, i.e. laying-out of coordinates, elevation, subtense and coordinates determination, can be carried out by using of total stations, in which the mathematic model of laying-out excavation cutting with coordinates method is derived. And the traditional distance-approaching method by setting-up instruments on midpoint is ameliorated to a coordinates-approaching one , in which the instruments can be set up freely. Meanwhile, The complicated computation of the laying-out procedures can be accomplished by means of PC-E500S or CASIO calculators to make the laying-out operation various and productivity improved obviously.
High-Speed Railway Track Comprehensive Measurement System Based on GNSS/INS Multi-sensor

Qi Li,Zhengdong Bai,Bobo Chen,Haohao Xin,Yuhang Cheng,Qiang Zhang

DOI: https://doi.org/10.1007/978-981-15-3707-3_1

2020-01-01

Abstract:Track measurement is an importantly basic and preliminary work to ensure high-speed, safe and smooth operation of trains. In the stages of design and construction, the high-speed railway track measurement at least includes the layout and measurement of all control networks, the subgrade deformation monitoring, and the track irregularity measurement. However, there are several problems such as long retest period, high labor cost, and low detection efficiency, which cannot fully meet the needs of large-scale high-speed railway tracks rapid detection in the stages of operation and maintenance. So, a set of track comprehensive measurement methods of high-speed railway based on GNSS/INS multi-sensor are proposed, and the corresponding system is developed. It has been applied to the actual track fine adjustment engineering, and compared with the Amberg track geometry measurement system based on total station coupled with level, and the results show that the proposed system has realized the integration of track subgrade deformation monitoring and track geometry absolute measurement and relative measurement, which fully meets the requirements of the Code for Engineering Survey of High-Speed Railway, and significantly improves the measurement efficiency.
A Fast Evaluation Method for Spatial Point Measurement Accuracy in a Large-Scale Measurement System

Yusong Liu,Wenbo Guo,Yuanyuan Pang,Bo Zheng

DOI: https://doi.org/10.3390/electronics13132428

IF: 2.9

2024-06-22

Electronics

Abstract:In the application domain of large-scale high-precision measurement systems, accurately calibrating the precision of point position measurements is a pivotal issue. Traditional calibration methods rely on laser interferometers and high-precision displacement stages, which are not only costly but also challenging to implement in fixed measurement systems. Addressing this challenge, this study introduces an evaluation method for the spatial point measurement accuracy in large-scale fixed high-precision measurement systems. The models for the relationship between the limit deviation and the maximum deviation of finite measurements were established, as well as the limit deviation and point position measurement accuracy. The spatial point position accuracy of the measurement field was calculated by the measurement errors of a calibration rod. The algorithm was validated using a large-scale measurement platform based on photogrammetric technology. Experimental results demonstrate that the method achieved a point position measurement accuracy calibration better than 0.1 mm within a 20 m measurement range, effectively enhancing the measurement data's accuracy and reliability. This research optimizes the calibration process for large-scale fixed measurement systems, improves calibration efficiency, and obviates the need for complex equipment to complete the calibration process, which is of considerable importance to the development of high-precision spatial point position measurement technology.

engineering, electrical & electronic,computer science, information systems,physics, applied
Remote Reference Magnetotelluric Processing Algorithm Based on Magnetic Field Correlation

Zhang Gang,Tuo Xianguo,Wang Xuben,Gao Song,Li Huailiang,Yu Nian,Liu Yong,Shen Tong

DOI: https://doi.org/10.1007/s40328-017-0203-y

IF: 1.768

2017-01-01

Acta Geodaetica et Geophysica

Abstract:Valid interpretations require precise and accurate determination of magnetotelluric impedance. Although remote reference magnetotellurics has been extensively investigated, majority of these studies have focused on the non-correlation between noise and signal or between the noise in the base station and that in the reference station. Few works have explored the correlation between magnetic signals in the base station and in the reference station. This study analyzes the effects of remote reference magnetotellurics on the sounding curve under different noise intensities in the base station. Results showed that regular remote reference magnetotellurics induce a limited quality-improving effect on the sounding curve and fail to satisfy the further data processing requirements at a low signal-to-noise ratio (SNR), suggesting that regular remote reference magnetotelluric methods cannot obtain an accurate transfer function under a low SNR for a time series. Comparison of various magnetic field data revealed that a strong correlation exists among magnetic signals 60 km apart at the Longmenshan area. Thus, the remote reference magnetotelluric method based on the magnetic field correlation between the base and reference stations is proposed to screen the power spectrum and undo the noise. The effectiveness and correctness of the proposed method are validated by the results of the theoretical and field data processing and of the intermediate data analysis, further proving that the remote reference magnetotelluric method based on magnetic field correlation is superior to the regular remote reference magnetotelluric method.
Discussion about adopted measure for distance-limited mobile station

Ni Weiming,Wang Zhiwei,Wang Yongping

DOI: https://doi.org/10.3969/j.issn.1671-0657.2007.01.017

2007-01-01

Abstract:The paper analyzed the reasons of limitation of base-line length between the mobile station and base station of GPS RTK because of the factors of transmitter etc, presented the methods of removing the distance limitation of mobile station, improving the construction efficiency.
Research on Spacecraft-Ground Station Iterative Measurement

SONG Bai-yan,ZHAN Ya-feng,LU Jian-hua

DOI: https://doi.org/10.3969/j.issn.1002-0802.2012.09.024

2012-01-01

Abstract:Aiming at the main feature of space-ground network,the paper,for improving the precision of spacecraft measurement,proposes an iterative measurement method between spacecraft and ground station.Based on the space-ground network model and the analysis of relevant measurement error,it describes in detail the space-ground measuring principle and the iterative process of network.Computer simulation is performed to check the effect of iterative measurement.The resut shows that this technology could improve the final measurement precision by 55%.

Analysis on Remote Distance Measurement Accuracy with Intermediate Method of Electronic Total Station

Study on Improving GPS Measurement Accuracy

Dynamic measurement technology based on dual electronic total stations and its application

Integrated Method for Measuring Distance and Time Difference Between Small Satellites

Study on Remote Monitoring System of 3D Scanning and Measuring Machine

Research on Distance and Direction Correction of GPS and Total Station Measurements in the Jingzhou Section of Yangtse River

On road section measurement and its data treatment

Discussion on the Method of Precise REM

A Procedure for Constructing Virtual Digital Outcrop Models (vdom) and Its Application to Accuracy Comparison of Rock Discontinuity Geometric Parameters Based on Two Photogrammetric Methods

Design and Application of a High Precision Intelligent Distance Measuring Device

APPLICATION OF LASER RANGING TECHOLOGY IN SLOPE ROMOTE MONITORING AND ERROR CORRECTION

Accuracy Comparison of Rock Discontinuity Geometric Parameters in Photogrammetry Based on Two Georeferencing Methods: Control Points and Geotagged Photos

Study on Quantitative Analysis Method of the Precision of Satellite Remote Sensing

Increase construction staking out efficiency with total station tachymeter

Remote value transmission and traceability technology of measuring instruments based on wireless communication

A New Method of Laying-out Excavation Cutting with Total Stations

High-Speed Railway Track Comprehensive Measurement System Based on GNSS/INS Multi-sensor

A Fast Evaluation Method for Spatial Point Measurement Accuracy in a Large-Scale Measurement System

Remote Reference Magnetotelluric Processing Algorithm Based on Magnetic Field Correlation

Discussion about adopted measure for distance-limited mobile station

Research on Spacecraft-Ground Station Iterative Measurement