Water Dispersible Carbon Nanotube/polyaniline Composite : Study of the Morphology and Electrical Conductivity

Ana López Cabezas,Yongqiang Feng,Lirong Zheng,Zhibin Zhang

IF: 4

2013-01-01

Synthetic Metals

Abstract:Water dispersible carbon nanotube/polyaniline composite : study of the morphology and electrical conductivity

What problem does this paper attempt to address?

Nanocomposites of Carbon Nanotube/Polyaniline with Pending Calix[8]Arene and Their External Stimuli Response Properties

Ming Jun Gao,Li Ping Li,Jian Xun Qiu,Xin Tao Zhang,Xiao Chun He,Shi Sheng Lv,Xing Fa Ma,Guang Li

DOI: https://doi.org/10.4028/www.scientific.net/msf.898.2286

2017-01-01

Materials Science Forum

Abstract:To functionalize the smart nanocomposites, the nanocomposites of CNTs/polyaniline with pending calix [8] arene were prepared. A series of characterizations were performed by SEM (scanning electron microscopy), the Fourier-Transform Infrared (FTIR) spectra, The UV-Vis (Ultra-violet visible spectroscopy), et al. The photoconductivity response to visible light and 808 nm laser with low-power were studied based on interdigital electrodes of Au on flexible PET (polyethylene terephthalate) film substrate with casting method. The results showed that the nanocomposites of CNTs/polyaniline with pending calix [8] arene exhibited good photoresponse to visible light and weak 808 nm laser, but its recoverability was very slow, it needed several hours, and the film-forming property of nanocomposite was not very good. This may be attributed to the results of increased hydrophobicity of nanocomposite because of introducing the calix [8] arene ring. In order to increase the film-forming technology of nanocomposites, the grapheme oxide were obtained with unzipping method of carbon nanotube (CNTs) for enhancing the hydrophilcity of carbon nanomaterials. The nanocomposites of grapheme oxide/polyaniline with pending calix [8] arene were obtained with similar methods, which showed improved film-forming property. The photoresponses to weak visible light and 808 nm laser also showed the similar results. It may develop the nanocomposite with external stimuli response, and have good potential applications in sensors, organic photocatalyst, et al.
Single Carbon Fiber/Acid-Treated CNT-Epoxy Composites by Electro- Micromechanical Technique and Wettability Test for Dispersion and Self-Sensing

Jung-Hoon Jang,Zuo-Jia Wang,Joel GnidaKouong,Woo-Il Lee,Jong-Kyoo Park

2009-01-01

Abstract:Dispersion and self-sensing evaluation for single-carbon fiber reinforced in three different acid-treated CNT-epoxy nanocomposites were investigated by electro-micromechanical techniques and wettability tests. Self-sensing based on contact resistivity exhibited more noise for single carbon fi- ber/acid-treated CNT-epoxy composites than it did for untreated CNT. However, the apparent modulus was higher the acid treated case than the untreated case which is attributed to better stress transfer. The interfacial shear strength (IFSS) between carbon fibers and the CNT-epoxy was lower than that between carbon fiber and neat epoxy due to the increased viscosity associated with the addition of the CNT. The CNT-epoxy nanocomposite exhibited more hydrophobicity than did neat epoxy. Change in the thermody- namic work of adhesion was consistent with changes in the IFSS but disproportional to that of the appa- rent modulus. The optimum condition of acid treatment on the need can be obtained instead of the max- imum condition.
Synthesis and Electrical Properties of Carbon Nanotube Polyaniline Composites

Yz Long,Zj Chen,Xt Zhang,J Zhang,Zf Liu

DOI: https://doi.org/10.1063/1.1786370

IF: 4

2004-01-01

Applied Physics Letters

Abstract:A multiwalled carbon nanotube∕polyaniline composite with cablelike morphology has been synthesized by an in situ chemical oxidative polymerization directed with cationic surfactant cetyltrimethylammonium bromide. It is interestingly found that with increasing carbon nanotube loading from 0 to 24.8wt%, the conductivity increases by two orders of magnitude and the Mott’s characteristic temperature T0 which depends on the hopping barrier decreases by three orders of magnitude. Furthermore, the low-temperature magnetoresistance has also changed the sign from positive to negative. The results reveal a strong coupling between the carbon nanotube and the tightly coated polymer chains, which enhances the average localization length and the electronic properties of the composites.
Single-walled Carbon Nanotube–polymer Composites: Electrical, Optical and Structural Investigation

E Kymakis,I Alexandou,GAJ Amaratunga

DOI: https://doi.org/10.1016/s0379-6779(01)00592-6

IF: 4

2002-01-01

Synthetic Metals

Abstract:We present a study on the interaction between single-walled carbon nanotubes (SWNTs) and the soluble polymer poly(3-octylthiophene) (P3OT). Composites of SWNTs embedded in the polymer matrix were fabricated by drop casting of the nanotube/P3OT mixture dissolved in chloroform and have been studied using absorption spectroscopy, electrical characterization methods and high-resolution electron microscopy. The electrical conductivity was measured as a function of the SWNTs content in the solution. As the nanotube concentration increases from 0 to 20wt.%, the conductivity of the resulting films increases by five orders of magnitude. The enhancement in conductivity can be explained by means of simple percolation path theory, resulting in an estimated percolation threshold of 11wt.%.
Electrospinning and Microwave Absorption of Polyaniline/polyacrylonitrile/multiwalled Carbon Nanotubes Nanocomposite Fibers

Zhichun Zhang,Fenghua Zhang,Xueyong Jiang,Yanju Liu,Zhanhu Guo,Jinsong Leng

DOI: https://doi.org/10.1007/s12221-014-2290-5

IF: 2.5

2014-01-01

Fibers and Polymers

Abstract:Electrical conductive nanocomposite fibers were prepared with polyaniline (PANI), polyacrylonitrile (PAN) and multi-walled carbon nanotubes (MWCNTs) via electrospinning. The morphology and electrical conductivity of the PANI/PAN/MWCNTs nanocomposite fibers were characterized by scanning electron microscope (SEM) and Van De Pauw method. Electrical conductivity of nanocomposite fibers increased from 1.79 S·m−1 to 7.97 S·m−1 with increasing the MWCNTs content from 3.0 wt% to 7.0 wt%. Compared with PANI/PAN membranes, the mechanical property of PANI/PAN/MWCNTs nanocomposites fiber membranes decreased. The microwave absorption performance of composite films was analyzed using waveguide tube, which indicated that with the thickness increasing the value of RL reduced from −4.6 to −5.9 dB.
Water‐dispersible Polyaniline‐carbon Nanotubes Composites with Interface Covalent Bond and Their Enhanced Electrochemical and Electrochromic Properties

Yuancheng Wang,Shanxin Xiong,Xiaoqin Wang,Jia Chu,Runlan Zhang,Bohua Wu,Ming Gong,Mengnan Qu,Zhen Li,Zhenming Chen

DOI: https://doi.org/10.1002/pen.25463

2020-01-01

Abstract:The water-dispersible electrochormic nanocomposites, polyaniline (PANI) connected multi-walled carbon nanotubes (MWCNTs) by covalent bond were synthesized through a grafting polymerization process of aniline monomer with functionalized MWCNTs.N,N '-dicyclohexylcarbodiimide (DCC) was used as dehydrant for functionalization process of MWCNTs withp-phenylenediamine (PPD). The transmission electron microscope (TEM), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), and Fourier transform infrared spectroscopy (FT-IR) were used to study the morphologies, thermal stabilities and chemical structures of the nanocomposites, respectively. The UV-vis absorbance spectra and cyclic voltammetry behaviors of nanocomposites were tested by UV-vis spectrometer and electrochemical workstation, respectively. It is shown show that PANI-MWCNTs nanocomposites not only exhibit good water solubility, but also exhibit excellent film-forming properties. The results confirm that the pi-pi interactions and interfacial covalent bond between PANI and MWCNTs endow PANI-MWCNTs excellent electrochemical and electrochromic properties. The conductive network composed of PANI and MWCNTs can significantly improve the ion transports, electron conduct and electrochromic performance of PANI. The PANI-MWCNTs-0.6% nanocomposite film shows highest optical contrast value (0.78) and shortest response time (3.8 seconds for coloring and 3.2 seconds for bleaching) among neat PANI and PANI-MWCNTs nanocomposites.
Study on the Morphology Properties of Carbon Nanotube/Polyaniline Composites Thin Film

Wen Ding,Vasileios Koutsos,Jinhai Si,Zhongxiao Song

DOI: https://doi.org/10.4028/www.scientific.net/amr.569.15

2012-01-01

Abstract:Active layer's morphologies properties are important for the optoelectronic devices. In this paper, the morphologies properties of the carbon nanotube/polyaniline composites thin film formed by spin coating were studied by the atomic force microscopy (AFM). The results showed that spin coating way greatly affects the thin film's topographic image, carbon nanotubes' concentration is the key that decide whether the interpenetrating network phase separation microstructure can be formed.
Electrical conductivity of carbon nanotube-filled miscible poly(phenylene oxide)/polystyrene blends prepared by melt compounding

Qiyan Zhang,Jingxia Wang,Bao-Hua Guo,Zhao-Xia Guo,Jian Yu

DOI: https://doi.org/10.1016/j.compositesb.2019.107213

2019-01-01

Abstract:Conductive polymer composites (CPCs) have attracted tremendous attention from both academia and industry for several decades. Unfortunately, high conductive filler loadings required for current CPCs to obtain insulator/conductor transition (usually defined as percolation threshold) significantly limit their development. Although some methods have been put forward over the past decades, no-one is cost effective and not compatible with industrial production. Here we reported a low cost and high processing efficiency method to develop high-performance CPCs with low percolation threshold. Miscible poly(phenylene oxide)/polystyrene (PPO/PS) blends with different compositions were used as the matrices, and the dispersion of carbon nanotubes (CNTs) was tuned by the viscosity of the matrices which result from different blend ratio. The best dispersion state of CNTs as well as the best electrical conductivity of the nanocomposites were found at the intermediate matrix viscosity that had balanced effects on infiltration of polymer molecules and breakage of primary CNT agglomerates. The percolation threshold of PPO/PS(35/65)/CNTs nanocomposites is 63% lower than that of PS/CNTs nanocomposites because of the significantly better dispersion state of CNTs. The electrical resistivity of PPO/PS(35/65)/2%CNTs is about 103 Ω cm which is 9 orders of magnitude lower than that of PS/2%CNTs.
Electrical Property of Carbon Nanotubes/polyphenylacetylene Composites

LI Xiang-mei,XU Xue-cheng,YU Wei,GU Ying-jun,SHI Yan,CHENG Rong-ming,CHEN Yi-wei

DOI: https://doi.org/10.3969/j.issn.1004-1656.2006.06.016

2006-01-01

Abstract:Polyphenylacetylene(PPA) was prepared with anhydrous AlCl_3 as catalyst,and sulfonated by concentrated H_2SO_4.The conductivities were studied for carbon nanotubes(CNT)/PPA and sulfonated CNT/PPA composite,which were prepared by mixing CNT with polymer in tetrahydrofuran under sonication.The room temperature conductivity of the two kinds of composites increases with increasing the ratio of CNT.The estimated percolation threshold of sulfonated CNT/PPA is 1% less than that of CNT/PPA and the amount of CNT added to PPA for obtaining the maximum conductivity is 10% of that of the sulfonated PPA.And the factors that affect the conduc-(tivity) of the composites were analyzed when the temperature changes. The XRD shows that the sulfonated PPA has created a new crystal structure on the interface of CNT.
Electrochemical Property of Well-Coated Multi-Walled Carbon Nanotube with Polyaniline-Cyclodextrin Polymer Composites

Wang Zhang,Ming Chen,Xiangdong Gong,Guowang Diao

DOI: https://doi.org/10.1149/ma2012-02/50/3488

2012-01-01

ECS Meeting Abstracts

Abstract:Abstract not Available.
Influence of Carbon Nanotubes on Thermal Stability of Water-Dispersible Nanofibrillar Polyaniline/Nanotube Composite

ana lopez cabezas,xianjie liu,qiang chen,shili zhang,lirong zheng,zhibin zhang

DOI: https://doi.org/10.3390/ma5020327

IF: 3.4

2012-01-01

Materials

Abstract:Significant influence on the thermal stability of polyaniline (PANI) in the presence of multi-walled carbon nanotubes (MWCNTs) is reported. By means of in-situ rapid mixing approach, water-dispersible nanofibrillar PANI and composites, consisting of MWCNTs uniformly coated with PANI in the state of emeraldine salt, with a well-defined core-shell heterogeneous structure, were prepared. The de-protonation process in PANI occurs at a lower temperature under the presence of MWCNTs on the polyaniline composite upon thermal treatment. However, it is found that the presence of MWCNTs significantly enhances the thermal stability of PANI's backbone upon exposure to laser irradiation, which can be ascribed to the core-shell heterogeneous structure of the composite of MWCNTs and PANI, and the high thermal conductivity of MWCNTs.
Modeling and characterization of the electrical conductivity on metal nanoparticles/carbon nanotube/polymer composites

Yang Wang,Sijian Lu,Wenke He,Shen Gong,Yunqian Zhang,Xinsi Zhao,Yuanyuan Fu,Zhenghong Zhu

DOI: https://doi.org/10.1038/s41598-022-14596-x

IF: 4.6

2022-06-22

Scientific Reports

Abstract:Flexible conductive films have good deformability and conductivity, and are expected to be used in flexible electronic devices. In this paper, four kinds of flexible conductive films were successfully prepared by compounding nano-sized metal (Ni, Cu, Au or AuCu alloy) particles to CNT surface and then dispersing to polydimethylsiloxane matrix. Experiment results show that the conductivity of these prepared films are almost two orders of magnitude higher than that of CNT/polydimethylsiloxane films with the same CNT loadings. A simulation model based on percolation network theory and Monte Carlo technology is introduced to study the influence of nanoparticles on the composite conductivity. Results confirmed that the introduction of nanoparticles effectively reduces the effective resistance of CNT and the tunnelling resistance at CNT junctions. The intrinsic conductivity and the length diameter ratio of CNT, the intrinsic conductivity, the size and the coverage ratio of nanoparticles are the core parameters affecting the conductivity of composite. Compared with CNT/polydimethylsiloxane films, the optimized theoretical conductivity of these nano-sized particles enhanced composites can be further improved.

multidisciplinary sciences
A Novel Conductive Composites: Preparation And Electrical Property Of Polypyrrole Coated Carbon Nanotubes

Bin Hao,Xiao-Xi Liang,Liang-Chao Li,Ke-Yu Chen,Qiu-Shi Xiao,Feng Xu

2010-01-01

Abstract:A novel conductive composites, carbon nanotubes/polypyrrole (MWNTs/PPy), were prepared by the in-situ polymerization. The structure, morphology and electric properties of the composites were investigated by XRD, TGA, FT-IR, SEM, four-point technique and materials/Impendence analyzer. It showed that the composites with mole rate of initiator to monomer (n(APs)/n(py)) equal to 1 and reactive time 12 h had excellent performance in conductivity and dielectric loss, and their the conductivity and dielectric loss arrived at respectively 67.8 S/cm and 6090 (0.5 GHz).
SYNTHESIS AND SUPERCAPACITANCE PERFORMANCE OF SULFONATED CARBON NANOTUBES MODIFIED POLYANILINE COMPOSITES

Sun Minqiang,Zhu Zhongze,Li Xingwei,Wang Gengchao

DOI: https://doi.org/10.3724/sp.j.1105.2011.10151

2011-01-01

Acta Polymerica Sinica

Abstract:Water-soluble sulfonated carbon nanotubes were prepared by diazotization.On this basis,a series of sulfonated carbon nanotubes(1~2 nm,8 nm,10~20 nm,30~50 nm) modified polyaniline composites were synthesized successfully using in situ oxidative polymerization method.FTIR spectra shows that the intensity ratio of I1580/I1490 increases with the decrease of the diameters of CNTs.Simultaneously,it can be found from the UV-Vis spectra that the absorption peak around 800 nm of the composites blue-shifts compared to the polyaniline nanorods.Aforementioned results indicate that the presence of the π-π interaction between the PANI and the sulfonated carbon nanotubes,and the charge transfer composites are formed,which increase as the diameter of CNTs decreases.Field emission scanning electron microscope(FESEM) images show the PANI/sSWCNT composite displays the morphological structure of the bundle of nanotubes coated with PANI while the PANI/sMWCNT composites exhibit the morphology of single nanotube coated with PANI.And with the increase of the diameters of carbon nanotubes,the diameters of the PANI/sMWCNT composites thicken gradually.The cyclic voltammetry results demonstrate that the composites have higher specific capacitance(309~457 F/g) compared to the PANI nanorods(271 F/g),and the specific capacitance of the composites increases with decreasing the diameter of CNTs.Moreover,the composites also have outstanding fast charge/discharge performance as electrode materials in the application of supercapacitors.
Effect of Carbon Nanotube Dispersion on Electrochemical Behavior of the CNTs/LiCoO2 Composite Cathode

Guo-ping Wang,Mei Li,Yong Qian,Li-fang Jia,Yu-qiang Tao,Jiang Qi,Xiaoying Lu,

DOI: https://doi.org/10.20964/2021.07.45

IF: 1.541

2021-07-01

International Journal of Electrochemical Science

Abstract:Carbon nanotubes (CNTs) are utilized as conductive additives in lithium ion battery. Particularly, the effect of surfactant type on the CNTs’ dispersion as well as correponding electrochemical behavior of LiCoO2 cathode is investigated. The results demonstrate that the dispersion of CNTs can be improved by both cationic and anionic surfactants, but the resulted electrodes show poor wettability with electrolyte. As a result, the electrochemical performance of corresponding LiCoO2-based cathode is worsened. Non-ionic polymer polyvinylpyrrolidone (PVP) act as an effective dispersant for promoting the dispersion of CNTs and improving the electrochemical performance of LiCoO2 cathode. In addition, CNTs after ball-milling show damaged structure and more agglomerates, which are not suitable for forming a continuous conductive network.
Progress of Electrical Property in Polymer/Carbon Nanotube Composites

XIN Fei,XU Guozhi,AN Chuantao,WANG Wei,LIU Tianran

DOI: https://doi.org/10.19491/j.issn.1001-9278.2013.03.002

2013-01-01

Abstract:This paper reviewed the recent advances in the electrical property of polymer/carbon nanotube(CNT) composites.CNTs could enhance polymer matrix's electrical property because of its high electrical conductivity.However,CNTs were extremely difficult to disperse in a polymer matrix and usually intend to agglomerate to form stabilized bundles.The main challenge in the preparation of CNT-reinforced composites was to find a way to make CNTs homogeneously dispersed in polymer matrix.So far,there were several methods for the dispersion of carbon nanobubes,such as solution mixing,in-situ polymerization,melt mixing and chemical functionalization of the carbon nanotubes,etc.Numerous studies showed that the percolation threshold and conductivity depend strongly on the polymer type and fabrication method,aspect ratio of CNTs,uniform spatial distribution of individual CNTs and degree of alignment.These influencing factors and preparation of high performance polymer/CNTs composites were described in this review.Moreover,both the current challenge and the future development towards the field of polymer/CNTs electrical conductive composites were also discussed in this article.
Highly Stable Carbon Nanotube/Polyaniline Porous Network for Multifunctional Applications

Wenqi Zhao,Yibin Li,Shiting Wu,Dezhi Wang,Xu Zhao,Fan Xu,Mingchu Zou,Hui Zhang,Xiaodong He,Anyuan Cao

DOI: https://doi.org/10.1021/acsami.6b11984

IF: 9.5

2016-01-01

ACS Applied Materials & Interfaces

Abstract:Three-dimensional carbon nanotube (CNT) networks with high porosity and electrical conductivity have many potential applications in energy and environmental areas, but the network structure is not very stable due to weak inter-CNT interactions. Here, we coat a thin polyaniline (PANI) layer on as-synthesized CNT sponge to obtain a mechanically and electrically stable network, and enable multifunctional applications. The resulting CNT/PANI network serves as stable strain sensors, highly compressible supercapacitor electrode with enhanced volume-normalized capacitance (632 F/cm3), and reinforced nanocomposites with the PANI as intermediate layer between the CNT fillers and polymeric matrix. Our results provide a simple and controllable method for achieving high-stability porous networks composed of CNTs, graphene, or other nanostructures.
Synthesis of Polyaniline-Mwnt Composite Nano-Tube and Electrical and Optical Properties

W Feng,WH Yi,YL Xu,YQ Lian,XG Wang,K Yoshino

DOI: https://doi.org/10.7498/aps.52.1272

IF: 0.906

2003-01-01

Acta Physica Sinica

Abstract:A composite of polyaniline (PANI) encapsulating mutilwall carbon nanaotube(MWNT) composite nanotube with nanometer size has been synthesized by insitu emulsion polymerization. Nanotube dimensions have been measured and the nature of the association between the components have been observed using SEM and TEM techniques, the diammer of nanocomposite tube is about 6070 nm.The improvement of thermal stability and crystallinity of nanocomposites have been evaluated by using TGA and XRD. The photoconductivity of PANIMWNT composite nanotube has been enhanced markedly and discussed by taking the photoinduced charge transfer between PANI and MWNT into consideration.
Thermal ageing of electrical conductivity in carbon nanotube/polyaniline composite films

ana lopez cabezas,yi feng,lirong zheng,zhibin zhang

DOI: https://doi.org/10.1016/j.carbon.2013.03.018

IF: 10.9

2013-01-01

Carbon

Abstract:The influence of carbon nanotubes on the thermal ageing effect of the electrical conductivity of composite thin films is presented. The composite thin films comprise carbon nanotube/polyaniline nanofibers. When subject to thermal treatment, the presence of nanotubes retards the loss of dopants from the polyaniline and enhances the thermal stability in electrical conductivity of the composite thin films. Specifically, an increase in temperature for the conductivity degradation and a significant reduction in the rate of the conductivity degradation of the composite thin films are observed. Upon prolonged heating, the composite thin films exhibit relative large conductivity at high nanotube content, while the polyaniline thin films become insulating.
Carboxylated multi-walled carbon nanotube/polyaniline composites for high-performance supercapacitor electrodes

Yanmin Wang,Yuansong Xiao,Xueliang Wu,Tingxi Li,Yong Ma

DOI: https://doi.org/10.1080/09243046.2022.2144123

IF: 2.92

2022-11-13

Advanced Composite Materials

Abstract:Multi-walled carbon nanotube (MWCNT)/polyaniline (PANI) composite and carboxylated multi-walled carbon nanotube (MWCNT-COOH)/PANI composites are fabricated via in situ chemical oxidative polymerization method. The crystallinity, chemical structure and morphology of the composites are investigated by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) and field-emission scanning electron microscopy (FESEM), respectively. Based on the different morphology, the formation mechanism of the composites is proposed and the influence of the morphology on the electrochemical performance is predicted. The electrochemical properties of the composites are evaluated by galvanostatic charge/discharge (GCD), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques. The MWCNT-COOH/PANI composite electrode shows higher specific capacitance than that of the MWCNT/PANI composite, as can be ascribed to the interpenetrating network structure of the MWCNT-COOH/PANI composite and the co-doping of DBSA and MWCNT-COOH. The MWCNT-COOH/PANI composite with 15% MWCNT-COOH presents the best electrochemical performance owing to the synergistic and comprehensive effect of the components. Using functionalized MWCNT provides an efficient approach to prepare high-performance composite materials for electrical energy storage fields.

materials science, composites

Water Dispersible Carbon Nanotube/polyaniline Composite : Study of the Morphology and Electrical Conductivity

Nanocomposites of Carbon Nanotube/Polyaniline with Pending Calix[8]Arene and Their External Stimuli Response Properties

Single Carbon Fiber/Acid-Treated CNT-Epoxy Composites by Electro- Micromechanical Technique and Wettability Test for Dispersion and Self-Sensing

Synthesis and Electrical Properties of Carbon Nanotube Polyaniline Composites

Single-walled Carbon Nanotube–polymer Composites: Electrical, Optical and Structural Investigation

Electrospinning and Microwave Absorption of Polyaniline/polyacrylonitrile/multiwalled Carbon Nanotubes Nanocomposite Fibers

Water‐dispersible Polyaniline‐carbon Nanotubes Composites with Interface Covalent Bond and Their Enhanced Electrochemical and Electrochromic Properties

Study on the Morphology Properties of Carbon Nanotube/Polyaniline Composites Thin Film

Electrical conductivity of carbon nanotube-filled miscible poly(phenylene oxide)/polystyrene blends prepared by melt compounding

Electrical Property of Carbon Nanotubes/polyphenylacetylene Composites

Electrochemical Property of Well-Coated Multi-Walled Carbon Nanotube with Polyaniline-Cyclodextrin Polymer Composites

Influence of Carbon Nanotubes on Thermal Stability of Water-Dispersible Nanofibrillar Polyaniline/Nanotube Composite

Modeling and characterization of the electrical conductivity on metal nanoparticles/carbon nanotube/polymer composites

A Novel Conductive Composites: Preparation And Electrical Property Of Polypyrrole Coated Carbon Nanotubes

SYNTHESIS AND SUPERCAPACITANCE PERFORMANCE OF SULFONATED CARBON NANOTUBES MODIFIED POLYANILINE COMPOSITES

Effect of Carbon Nanotube Dispersion on Electrochemical Behavior of the CNTs/LiCoO2 Composite Cathode

Progress of Electrical Property in Polymer/Carbon Nanotube Composites

Highly Stable Carbon Nanotube/Polyaniline Porous Network for Multifunctional Applications

Synthesis of Polyaniline-Mwnt Composite Nano-Tube and Electrical and Optical Properties

Thermal ageing of electrical conductivity in carbon nanotube/polyaniline composite films

Carboxylated multi-walled carbon nanotube/polyaniline composites for high-performance supercapacitor electrodes