Abstract:The effects of rare earth erbium (Er) micro-additions on the microstructures and mechanical properties of 2024 aluminum alloy were investigated. The microstructures and fracture surfaces of specimens prepared via high-energy ball milling, cold isostatic pressing and microwave sintering were carried out by optical microscopy (OM) and scanning electron microscopy (SEM). Under the conditions of sintering heating rate of 20 min/°C and soaking time of 30 min at 490 °C, it was found that with the increase in Er addition, the grain size first decreased then increased, and it reached a minimum size of about 5 μm when the Er content was 0.6%, showing that the grains were refined. At the same time, the compactness and microhardness reached maximum levels, which were 97.6% and 94.5 HV, respectively. Moreover, the tensile strength and elongation reached the peak at 160.5 MPa and 4.4%, respectively. The dynamic mechanical response of Er/2024Al alloy with different Er content was studied through a split Hopkinson pressure bar (SHPB) at strain rates of 600 s−1 and 800 s−1, respectively. Both at the strain rates of 600 s−1 and 800 s−1, the dynamic yield stress of the specimens increased gradually with an increase in Er content. For the 0.6 wt.% Er specimen, the dynamic yield stress reached 371.3 MPa at a strain rate of 800 s−1, which was 28.2% higher than that at a strain rate of 600 s−1. When the strain rate is 800 s−1, the deformation degree of the 0.6 wt.%Er specimen is 55.3%, which is 14.7% higher than for the Er-free one, and there are adiabatic shear bands formed in the 0.6 wt.%Er specimen. Through a fracture analysis of the samples, a certain number of dimples appeared in the fracture of an impact specimen, indicating that the addition of Er improved the toughness of the material. This research can provide a reference for the development and application of high-performance aluminum alloy in automotive structural materials.

Er-containing microalloyed aluminum alloys: a review

Effect of Erbium Micro-Additions on Microstructures and Properties of 2024 Aluminum Alloy Prepared by Microwave Sintering

Effect of Minor Er Additions on the Microstructures and Mechanical Properties of Cast Al-Cu-Mg-Ag Alloys

Microstructure and mechanical properties of Al-Mg-Mn-Er-Zr alloys fabricated by laser powder bed fusion

Effects of addition of Er and Zr on microstructure and mechanical properties of Al–Cu–Mn–Si–Mg alloy

Effects of rare earth Er additions on microstructure development and mechanical properties of die-cast ADC12 aluminum alloy

Influence of erbium addition on the defects of selective laser-melted 7075 aluminium alloy

Enhanced multiple precipitation and long-term stability in AlCuMgSi(Sc) alloys with Er additions

Characteristics of microstructural and mechanical evolution in 6111Al alloy containing Al3(Er,Zr) nanoprecipitates

Effect of Er and Zr additions and aging treatment on grain refinement of aluminum alloy fabricated by laser powder bed fusion

Enhanced Strength–Corrosion Synergy of 6061Al Casting Alloy Through Erbium Addition

Study on Phases Formation and Modification Ability of Rare Earth Elements La, Ce, Sm and Er in Al–Zn–Mg–Cu–Zr Alloy

Effect of Al–Er–Zr Master Alloy on Grain Refinement After Heat Treatment

Multi-alloying effect of Ti, Mn, Cr, Zr, Er on the cast Al-Zn-Mg-Cu alloys

Effect of Ca, Sc and Er Microalloying on the Microstructure and Properties of AZ61 Alloys by Electromagnetic Casting

Effect of Rare Earth Elements Erbium and Europium Addition on Microstructure and Mechanical Properties of A356 (Al–7Si–0.3Mg) Alloy

Microstructure and Mechanical Properties of an Er-Modified Al–Mg–Mn–Sc–Zr Alloy Processed by Selective Laser Melting

Synergistic Effect of RE (La, Er, Y, Ce) and Al-5Ti-B on the Microstructure and Mechanical Properties of 6111Aluminum Alloy

Densification, Microstructure and Anisotropic Corrosion Behavior of Al-Mg-Mn-Sc-Er-Zr Alloy Processed by Selective Laser Melting

Nucleation of L12-Al3M (M = Sc, Er, Y, Zr) Nanophases in Aluminum Alloys: A First-Principles ThermodynamicsStudy

Effect of Chromium on Microstructure and Mechanical Properties of Al–Cu–Er–Zr Alloy