Dispersion Compensation of 10gb/s WDM System Using Chirped Fiber Grating

Jian Cao

2000-01-01

Abstract:A linearly chirped fiber grating has been written via two time exposure method with a uniform phase mask.Dispersion compensation of single channel of 10Gb/s WDM system has been demonstrated,using this chirped fiber grating.The power penalty of dispersion compensation after 180km transmission is 1dB.

What problem does this paper attempt to address?

Multichannel Dispersion Compensation by Using a Single Chirped Fiber Bragg Grating

XH Li,XF Chen,MY Zhou,SZ Xie

DOI: https://doi.org/10.1117/12.520640

2004-01-01

Abstract:In this paper, with the superimposed technique a 4-channel chirped grating in a fiber for multi-channel dispersion compensation is been written. We have performed a dispersion compensation experiment with a system using a 10Gbit/s externally modulated laser. The experimental results show that measured BER of the all channels has the power penalty less than ±0.3dB when the grating is inserted through a circulator in front of the 100km transmission fiber.
Chirped fiber grating with the apodization of parabola squared function for dispersion compensation of chirped Gaussian pulses

Yaohui Gao,Guoying Feng,Xiaodong Li,Jianguo Chen

2006-01-01

Abstract:Theoretical research and numeric model of dispersion compensation of chirped super Gaussian pulses are presented, using chirped fiber grating with the apodization of parabola squared function. It shows that pulses, after transmitting in a fiber length, will become broadened because of dispersion. When using chirped fiber grating with the apodization of parabola squared function, pulses can be compensated with the results that the width of pulses is more narrow and the max-power is higher, compared with using chirped fiber grating with the apodization of Gaussian function. The pulses are distorted after being compensated. The max-power has something to do with the order of Gaussian pulses.
Transmission Performance Improvement in Microwave/Millimeter-Wave Optical System Using Chirped Fiber Grating

Shilie Zheng,Xianmin Zhang

DOI: https://doi.org/10.1007/s10762-005-6172-1

2005-01-01

International Journal of Infrared and Millimeter Waves

Abstract:A chirped fiber grating (CFG) written by the moving fiber/phase mask scanning beam technique with a uniform mask is used to demonstrate the dispersion compensation in the externally modulated microwave/millimeter-wave over fiber system It is found that the use of the CFG is an efficient way to compensate for the severe RF power degradation induced by the fiber chromatic dispersion, which results in a significant improvement in the transmission performance. The signal to noise ratio is improved from 4.8 dB to 24.4 dB when 10.58 GHz RF signal carrying 5 Mbit/s QPSK format data is transmitted over 35 km single mode fiber.
High Dispersion Compensation Mirrors for Pulse Stretching in Chirped Pulse Amplifiers

Wenjia Yuan,weidong shen,Xu Liu

DOI: https://doi.org/10.1364/oic.2013.wd.7

2013-01-01

Abstract:A high dispersion compensation mirror for chirped pulse amplification systems, which can provide a considerable value for positive group delay dispersion of 600fs2, and an average reflectance of over 99.9% from 1010 to 1070 nm.
Compensation of Dispersion-Induced Power Fading with Adjustment-Free Operation

Xiang Zhu,Tao Jin,Ying Fu,Hao Chi,Dong Li,Lulu Zuo,Weiming Liu,Qihang Wang

DOI: https://doi.org/10.1117/1.oe.58.6.060504

IF: 1.3

2019-01-01

Optical Engineering

Abstract:A scheme for compensation of dispersion-induced power fading is proposed and experimentally demonstrated. The system transmits two modulated laser lights via a wavelength division multiplexer and a wavelength division demultiplexer. By optimizing the power ratio and the phase difference between the two modulated signals, the dispersion-induced power fading can be adequately compensated. A key significance of our approach is that no adjustments are required when the input radio frequency signal scans over a broad bandwidth of 1 to 12 GHz. We successfully demonstrate the compensation of the power fading for both 20- and 30-km fiber links. An improvement of spurious-free dynamic range is also achieved. (C) 2019 Society of Photo-Optical Instrumentation Engineers (SPIE)
Tunable Dispersion Compensation in 40-Gb/s System Using a Thermally Controlled Fiber Bragg Grating

J Sun,YT Dai,YJ Zhang,XF Chen,SZ Xie

DOI: https://doi.org/10.1117/12.636647

2005-01-01

Abstract:A cost-effective tunable dispersion compensator using reconstruction-equivalent-chirp method is fabricated. Only uniform phase mask, sub-micron precision and uniform thin metal film are required in the fabrication. The group delay ripple is less than 14 ps during the whole tuning range. An experiment in 40-Gb/s system is demonstrated with a power penalty of 0.7dB.
A comparative study of chromatic dispersion compensation in 10 Gbps SMF and 40 Gbps OTDM systems using a cascaded Gaussian linear apodized chirped fibre Bragg grating design

Isidore Nsengiyumva,Elijah Mwangi,George Kamucha

DOI: https://doi.org/10.1016/j.heliyon.2022.e09308

IF: 3.776

2022-04-22

Heliyon

Abstract:Optical time domain multiplexed (OTDM) technology helps to respond to the need for increased capacity and demand in internet traffic using optical transmissions. High-speed optical networks are highly affected by chromatic dispersion (CD) that causes pulse broadening and intersymbol interference (ISI) at the light detector. This paper presents a comparative analysis of chromatic dispersion compensation on 10 Gbps single mode fibre (SMF) and 40 Gbps OTDM operating at C-band using Gaussian apodized linear chirped fibre Bragg grating, Erbium Doped Fibre Amplifier (EDFA) and uniform fibre Bragg grating (UFBG) hybrid approach in OptiSystem 18. A cascade of four UFBG and chirped Bragg gratings design approach presents minimal improvement in the quality factor and achievable single mode fibre length. Quality factor results at a reference wavelength of 1550 nm were obtained for respective chirped Bragg grating lengths of 8 mm, 20 mm, 50 mm, 87 mm, and 90 mm using linear Gaussian apodization. The Q-factor results obtained using the proposed simulation model for single 10 Gb/s channel were respectively 51.14 dBm over 30 km at a grating length of 20 mm and 15.64 dBm over 150 km at 45 mm of grating length. Different eye-diagrams corresponding to varying grating lengths have also been presented for 10 Gb/s and 40 Gb/s at corresponding SMF lengths.
Thermally Tunable Dispersion Compensator in 40-Gb/s System Using FBG Fabricated with Linearly Chirped Phase Mask

Jie Sun,Yitang Dai,Xiangfei Chen,Yejin Zhang,Shizhong Xie

DOI: https://doi.org/10.1364/opex.14.000044

IF: 3.8

2006-01-01

Optics Express

Abstract:An improved design and fabrication method of nonlinearly chirped fiber Bragg gratings is demonstrated. Based on reconstruction-equivalent- chirp method, the nonlinearly chirped fiber Bragg grating is realized with a linearly chirped phase mask instead of a uniform one, which improves the performance of the device. Coated with uniform thin metal film, the obtained grating works as a tunable dispersion compensator with a tuning range ~200ps/nm, peak-to-peak group delay ripple <14ps and 3-dB bandwidth approximately 2nm. Employing this device, the power penalty in a 40- Gb/s X5/10km conventional single mode fiber using carrier suppressed return-to-zero format is less than 0.7dB at a BER=10-10.
Dispersion Compensation CFBG in 100km 10gbit/s Recirculating Systems

Yang Aiying,Wang Ziyu,Zhang Zhaoyi,Chen Zhangyuan,Wu Deming

DOI: https://doi.org/10.1007/s11767-003-0062-2

2003-01-01

Abstract:A 10 Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10 −9 . The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4×167.1km) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of ±5GHz. At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.
Tunable Polarization Mode Dispersion and Chromatic Dispersion Compensation with Chirped Fiber Gratings

Lina He,Yejin Zhang,Yitang Dai,Shizhong Xie

DOI: https://doi.org/10.1117/12.688251

2006-01-01

Abstract:We have developed a thermally tunable module to compensate polarization mode dispersion (PMD) and chromatic dispersion (CD) simultaneously. In this module, twins of linearly chirped fiber Bragg gratings (LCFBGs) are used to compensate PMD and one non-linearly chirped FBG (NLCFBG) is used to compensate CD in 40Gb/s optical fiber communication system. The fiber Bragg gratings are coated with uniform thin metal film, and by changing the applied current through the film, the tunable compensation for PMD and CD is achieved. The fabrications of the LCFBG and NLCFBG are both utilizing the linearly chirped phase mask, making the fiber Bragg gratings easy to obtain.
Numerical Investigation of Dispersion‐managed System with Concatenated Chirped Fiber Bragg Grating

L Zhu,GZ Wang,L Xia,SZ Xie

DOI: https://doi.org/10.1002/mop.10264

IF: 1.311

2002-01-01

Microwave and Optical Technology Letters

Abstract:Concatenated chirped fiber Bragg grating (CBG) has been used to compensate for the dispersion in an optical‐fiber communication system. Dispersion compensation fiber (DCF) is replaced with CBG in normalized sections of a 10‐Gbit/s dispersion‐managed system over 800 km. The performance of this system was improved by adding an optical filter behind the CBG in each normalized section. © 2002 Wiley Periodicals, Inc. Microwave Opt Technol Lett 33: 163–165, 2002; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.10264
Transmission Distance Extension of Directly Modulated Tunable V-cavity Laser Using AWG Wavelength Detuning

Yuan Zhuang,Qiaoli Li,Yiqing Yang,Jianjun Meng,Jiasheng Zhao,Jian-Jun He

DOI: https://doi.org/10.1109/JPHOT.2020.2988617

IF: 2.4

2020-01-01

IEEE Photonics Journal

Abstract:Directly modulated tunable lasers are highly desirable for constructing dense-wavelength division multiplexing (DWDM) access networks, owing to their advantages of low cost, compact size and low power consumption. However, the transmission distance for 10 Gbps is usually limited to about 10 km in the telecom C-band in standard single-mode fiber (SMF) due to wavelength chirp. Here we propose and demonstrate a simple technique for extending the transmission distance by detuning the wavelength of a tunable V-cavity laser with respect to DWDM multiplexers. Experiment results show that 10 Gbps signal can be transmitted error-free (BER<10(-12)) over 20 km SMF with a wavelength-detuning with respect to a Gaussian-type arrayed waveguide grating (AWG) without dispersion compensation. The power penalty is only 1 dB compared to the back-to-back transmission.
System Stimulation for Dispersion Compensation with Nonideal Chirped Fiber Bragg Grating

Lin Zhu,Guozhong Wang,Li Xia,Shizhong Xie

DOI: https://doi.org/10.1023/A:1015097906521

2002-01-01

International Journal of Infrared and Millimeter Waves

Abstract:Chirped fiber Bragg grating (CBG) has been used to compensate the dispersion in the optical fiber communication system. We substitute dispersion compensation fiber (DCF) with CBG in the 10Gbit/s disperion-managed system over 1100km. In order to get system performance in the nonideal situation, the parameters of CBG are varied from the designed optimum in some extent. Post-, pre- and dual-compensation methods are compared.
Dynamic Dispersion Compensation in a 40 Gb/s Single-Channeled Optical Fiber Communication System

Li Yan,Xu Tianhua,Jia Dagong,Jing Wencai,Hu Hao,Yu Jinlong,Zhang Yimo

DOI: https://doi.org/10.3321/j.issn:0253-2239.2007.07.004

2007-01-01

Acta Optica Sinica

Abstract:A dynamic chromatic dispersion (CD) compensating technique for a 40 Gb/s single-channeled optical fiber communication system is demonstrated. The tunable dispersion compensator is composed of 2 × 2 optical switches, dispersion compensating fiber etc. For controlling the tunable dispersion compensator, a feedback signal is obtained by detecting the narrow band electrical power centered at 12 GHz, and the electrical power increases with the decrease of the accumulated chromatic dispersion. In experiment, the maximal response time of the system is 0.7 s. The compensating range and precision reach 81.55 ps/nm and 5.28 ps/nm respectively which can be further improved by adding the number of optical switches and reducing the length of dispersion compensating fiber. Experiments indicated that the dynamic dispersion compensating system can significantly improve the performance of 40 Gb/s optical communication systems according to the eye diagram before and after dispersion compensating.
On-Chip Multichannel Dispersion Compensation and Wavelength Division MUX/DeMUX Using Chirped-Multimode-Grating-Assisted Counter-Directional Coupler

Zhixiao Lv,Jiangbing Du,Zuyuan He

DOI: https://doi.org/10.3390/photonics11020110

IF: 2.536

2024-01-26

Photonics

Abstract:On-chip optical dispersion compensation and wavelength division multiplexing/demultiplexing (WDM) are highly demanded functions for optical communications. In this work, we proposed a multichannel dispersion compensation structure based on chirped multimode grating within a counter-directional coupler (CMG-CDC). Simultaneous wavelength division multiplexing and demultiplexing can be realized within a compact footprint. A device design for four-channel CMG-CDC at the C/L (1530–1565 nm) band is presented with a channel spacing of 20 nm assisted by a grooved multimode waveguide structure. The average dispersion for all channels is about −2.25 ps/nm with a channel bandwidth of about 3.1 nm. The device is highly compact and highly scalable, which makes it rather convenient for increasing the group velocity dispersion (GVD) and channel number, indicating flexible applications for versatile systems, including typically coarse wavelength division multiplexer four-lane (CWDM4) transceivers.

optics
Tunable Dispersion Compensator For 40-Gb/S Optical Transmission Systems Fabricated By Reconstruction And Equivalent Chirp Method

Yt Dai,Xf Chen,Y Shi,Mh Chen,My Zou,Sz Xie

DOI: https://doi.org/10.1109/cleo.2005.202145

2005-01-01

Abstract:Variable chromatic dispersion in 40-Gb/s fiber system is compensated accurately by the FBG designed with reconstruction-equivalent-chirp method. High performance with tunable range of 175ps/nm and group delay ripple about +/- 5ps is reported. (c) 2005 Optical Society of America.
Numerical Analysis of Specially Sample Fiber Bragg Grating for Dispersion Compensation

L Zhu,GZ Wang,L Xia,SZ Xie

DOI: https://doi.org/10.1117/12.444538

2001-01-01

Abstract:A kind of specially sampled fiber Bragg grating (SSBG) has been recently proposed to compensate the dispersion in the optical fiber communication system. We substitute dispersion compensation fiber (DCF) with SSBG in the 10Gbit/s dispersion-managed system over 1000km. Post- and pre-compensation methods are compared. The dispersion compensation effect of SSBG is also compared with the chirp Bragg grating (CBG).
System simulation of dispersion compensation with specially sampled fiber Bragg grating

Lin Zhu,Guozhong Wang,Li Xia,Shizhong Xie

DOI: https://doi.org/10.1016/S0030-4018(01)01505-X

IF: 2.4

2001-01-01

Optics Communications

Abstract:A kind of specially sampled fiber Bragg grating (SSBG) has been recently proposed to compensate the dispersion in the optical fiber communication system. We substitute dispersion compensation fiber with SSBG in the 10 Gbit/s dispersion-managed system over 1000 km. Post- and pre-compensation methods are compared. The dispersion compensation effect of SSBG is also compared with the chirp Bragg grating.
New dispersion compensation method for high-speed wavelength division multiplexed optical transmission systems

Chongcheng Fan,Jian Song

1995-01-01

Tien Tzu Hsueh Pao/Acta Electronica Sinica

Abstract:A new dispersion compensation method for high-speed terrestrial cascaded Erbium-Doped Fiber Amplifier wavelength division multiplexed (WDM) optical transmission systems is proposed. By means of specially designed dispersion-shifted fiber (SDDSF) with zero dispersion wavelength around 1.6 ��m and dispersion slope S0=0.05ps/km/nm, -2--4ps/km/nm dispersion is generated at 1550 nm to avoid severe four-wave mixing in WDM systems using ITU-T G.653 DSF. The positive dispersion of ITU-T G.652 standard single-mode fiber is utilized to compensate for the negative dispersion of SDDSF over 1530-1570nm (EDFA bandwidth). With this method, dispersion induced eye opening penalty could still be less than 1dB after 1000km fiber transmission in systems with bit-rate higher than 10Gb/s per channel.
Wideband Multichannel Dispersion Compensation Based On A Strongly Chirped Sampled Bragg Grating And Phase Shifts

Yt Dai,Xf Chen,J Sun,Sz Xie

DOI: https://doi.org/10.1364/OL.31.000311

IF: 3.6

2006-01-01

Optics Letters

Abstract:A novel multichannel dispersion compensator based on a strongly chirped sampled Bragg grating with phase shifts is demonstrated experimentally. With a single phase mask, various channel spacings and dispersion can be achieved by proper control of the sampling period and the phase shifts. A 100 GHz channel-spacing compensator with a dispersion of -1000 ps/nm and another 200 GHz channel-spacing compensator with a dispersion of -500 ps/nm are designed. As an example, a 40 channel, 100 GHz channel-spacing compensator with a dispersion of similar to-560 ps/nm is fabricated. All the designs are based on one phase mask, thus showing the flexibility of our method. (c) 2006 Optical Society of America.

Dispersion Compensation of 10gb/s WDM System Using Chirped Fiber Grating

Multichannel Dispersion Compensation by Using a Single Chirped Fiber Bragg Grating

Chirped fiber grating with the apodization of parabola squared function for dispersion compensation of chirped Gaussian pulses

Transmission Performance Improvement in Microwave/Millimeter-Wave Optical System Using Chirped Fiber Grating

High Dispersion Compensation Mirrors for Pulse Stretching in Chirped Pulse Amplifiers

Compensation of Dispersion-Induced Power Fading with Adjustment-Free Operation

Tunable Dispersion Compensation in 40-Gb/s System Using a Thermally Controlled Fiber Bragg Grating

A comparative study of chromatic dispersion compensation in 10 Gbps SMF and 40 Gbps OTDM systems using a cascaded Gaussian linear apodized chirped fibre Bragg grating design

Thermally Tunable Dispersion Compensator in 40-Gb/s System Using FBG Fabricated with Linearly Chirped Phase Mask

Dispersion Compensation CFBG in 100km 10gbit/s Recirculating Systems

Tunable Polarization Mode Dispersion and Chromatic Dispersion Compensation with Chirped Fiber Gratings

Numerical Investigation of Dispersion‐managed System with Concatenated Chirped Fiber Bragg Grating

Transmission Distance Extension of Directly Modulated Tunable V-cavity Laser Using AWG Wavelength Detuning

System Stimulation for Dispersion Compensation with Nonideal Chirped Fiber Bragg Grating

Dynamic Dispersion Compensation in a 40 Gb/s Single-Channeled Optical Fiber Communication System

On-Chip Multichannel Dispersion Compensation and Wavelength Division MUX/DeMUX Using Chirped-Multimode-Grating-Assisted Counter-Directional Coupler

Tunable Dispersion Compensator For 40-Gb/S Optical Transmission Systems Fabricated By Reconstruction And Equivalent Chirp Method

Numerical Analysis of Specially Sample Fiber Bragg Grating for Dispersion Compensation

System simulation of dispersion compensation with specially sampled fiber Bragg grating

New dispersion compensation method for high-speed wavelength division multiplexed optical transmission systems

Wideband Multichannel Dispersion Compensation Based On A Strongly Chirped Sampled Bragg Grating And Phase Shifts