Planar Waveguide Multiplexers/Demultiplexers in OpticalNetworks: from ImprovedDesigns to Applications

Sailing He,Jun Song,Jian‐Jun He,Daoxin Dai

DOI: https://doi.org/10.1201/b10371-28

2018-01-01

Abstract:Planar waveguide multiplexers/demultiplexers in optical networks : From improved designs to applications

What problem does this paper attempt to address?

Design and Numerical Optimization of A Mode Multiplexer Based on Few-Mode Fiber Couplers

Yiwei Xie,Songnian Fu,Hai Liu,Hailiang Zhang,Ming Tang,P. Shum,Deming Liu

DOI: https://doi.org/10.1088/2040-8978/15/12/125404

IF: 2.1

2013-01-01

Journal of Optics

Abstract:Mode division multiplexing (MDM) transmission based on few-mode fibers (FMFs) appears to be an alternative solution for overcoming the capacity limit of single-mode fibers (SMFs). A FMF coupler-based mode division multiplexer/demultiplexer (MMUX/DeMMUX) is proposed and theoretically investigated after the fabricated FMF is characterized. MMUXs/DeMMUXs with a mode contrast ratio (MCR) of more than 20 dB can be obtained for two-mode multiplexing and three-mode multiplexing over a wavelength span of 60 and 10 nm, respectively. We numerically verify the proposed MMUX/DeMMUX which has the advantages of high MCR, easy fabrication and maintenance, and low wavelength dependence.
Design of an Ultracompact MMI Wavelength Demultiplexer in Slot Waveguide Structures.

Jinbiao Xiao,Xu Liu,Xiaohan Sun

DOI: https://doi.org/10.1364/oe.15.008300

IF: 3.8

2007-01-01

Optics Express

Abstract:Based on a multimode interference (MMI) coupler in slot waveguide structures, an ultracompact wavelength demultiplexer operating at 1.30 and 1.55mum wavelengths is proposed and designed by using a full-vector mapped Galerkin mode solver and a modified three-dimensional full-vector beam propagation method. The tapered waveguide structures are applied to connect the input/output channels and the MMI section for reducing excess loss. The modal characteristics of the slot waveguides are analyzed and the evolution of the injected field in whole device are demonstrated. The results show that a MMI section of 119.8mum in length, which is only 27.5% length of that of the MMI coupler by using conventional rib waveguides, is achieved with the contrasts of 26.03 and 28.14dB at wavelengths 1.30 and 1.55mum, respectively, and the insertion losses are below 0.2dB at both wavelengths.
2D-Awg-based Optical Multiplexers/Demultiplexers

杨建义,江晓清,贾科淼,李锡华,王明华,吴亚明,王跃林

DOI: https://doi.org/10.3321/j.issn:1005-0086.2004.09.005

2004-01-01

Abstract:Based on the concepts of the 2-dimension diffraction grating and the planar waveguide array,a novel optical multiplexer/demultiplexer (Mux/Demux) employing the 2-dimension arrayed-waveguide grating is proposed.Since the direction of the diffraction route is determined by the vectorial combination of the dispersion values in two directions,the 2-dimension wavelength demultiplexing can be realized by properly controlling the values of the free spectral ranges.Then the input and output accessing ports of the Mux/Demux can be set in 2 diemnsions,with which the capability to design high-channel-count optical Muxs/Demuxs is improved.The properties and the possible applications of this Mux/Demux are discussed in this paper.
Integrated Waveguide WDM Demultiplexers

He, J.-J.,Lamontagne, B.,Erickson, L.,Delige, A.

DOI: https://doi.org/10.1109/cleopr.1999.814734

1999-01-01

Abstract:Addresses some key issues in integrated waveguide demultiplexer technology including insertion loss, inter-channel crosstalk, and polarization sensitivity and compares and contrasts the two different contenders, etched diffraction grating and arrayed waveguide demultiplexers. Theoretical and experimental results of the effects of grating patterning defects on crosstalk are presented, as well as a novel, easy-to-make, integrated polarization compensator.
Design of Hybrid Free-Space Wavelength-Division Multiplexers for Integration

XG Deng,JY Yang,JZ Zou,RT Chen

DOI: https://doi.org/10.1117/12.469645

2002-01-01

Abstract:We design a hybrid free-space wavelength-division multiplexers (MUX) that favor integration of matured high performance grating-based MUX and planar waveguide devices. By optimizing the component interfaces, we pursuit a divide-and-conquer method in the proposed hybrid integration. Meanwhile, a novel 6-channel coarse MUX based on layered diffractive optics is successfully designed. These two methods combined are promising in integrating multiple optical functions with cost-effective mass production.
Design and simulation of a planar integrated demultiplexer for coarse WDM

Zhongyan Sheng,Sailing He,Lifang Lou

DOI: https://doi.org/10.1016/j.optcom.2003.07.035

IF: 2.4

2003-01-01

Optics Communications

Abstract:A planar integrated demultiplexer is designed for coarse wavelength division multiplexing (WDM) applications. The demultiplexer chip has no input or output waveguides, and simply consists of a single-mode slab waveguide and a concave reflective grating. The grating is strictly designed to diffract the multiplexed input light and focus different wavelengths on different positions on a cutting edge of the chip. A single-mode input fiber and some multi-mode output fibers are located on the cutting edge, being used as input and output channels. A numerical simulation is given to verify a design of an 8-channel CWDM chip. The results show that this demultiplexer has good focused output fields, a low loss, and a good spectral response with flat-top wide passband.
Multifunctional Optical Waveguide Chips

JY Yang,F Zhao,DC An,RT Chen

DOI: https://doi.org/10.1117/12.469639

2002-01-01

Abstract:Based on polymeric materials, the possibilities of monolithic integration of various optical waveguide components are discussed and, especially, the efforts to realize the functions of optical modulation and amplification on a single optical chip are made. Exploration of more capabilities of optical waveguides is also emphasized. The work on exploring functions of optical waveguides for the applications in WDM components and photonic phased-array radar systems are presented and multifunctional optical waveguide chips with the explored functions are fabricated.
Propagation Characteristic Analysis and Applications of Spatial Four-Waveguide System

Haifeng Zhou,Jianyi Yang,Minghua Wang,Xiaoqing Jiang

DOI: https://doi.org/10.3321/j.issn:0253-2239.2006.12.003

2006-01-01

Abstract:By employing Marcatili's principle, the two-dimensional spatial four-waveguide system is decomposed as two perpendicular five-layer slab waveguides independently in the cross-section of the waveguides. The analytical model that can be interpreted appropriately by variable separation method is proposed. The first order correction for deviations of the model and practical structure is done by perturbation theory. The expressions of the first and second order propagation constants, static field distributions, coupling coefficient and propagation characteristic are presented. The feasibility and accuracy of the model are demonstrated by comparing the calculation results with finite difference solving semi-vector wave equation and beam propagation method. A coarse wavelength demultiplexer based on spatial four-waveguide system, including three common wavelengths 1.31 μm, 1.49 μm, and 1.55 μm of the triplex transistor in today's fiber-to-home, is designed with the insertion loss 0.68 dB. Further optimization of the separate outputs and waveguide structure can obtain higher qualities.
Novel Wavelength Multiplexer Using (<italic>N</italic> + 1) × (<italic>N</italic> + 1) Arrayed Waveguide Grating and Polarization-Combiner-Rotator on SOI Platform

Jun Zou,Xiao Ma,Xiang Xia,Changhui Wang,Ming Zhang,Jinhua Hu,Xuyang Wang,Jian-Jun He

DOI: https://doi.org/10.1109/JLT.2021.3053837

IF: 4.7

2021-01-01

Journal of Lightwave Technology

Abstract:We propose an ultra-compact novel wavelength multiplexer employing a (N + 1) × (N + 1) arrayed waveguide grating (AWG) and a polarization-combiner-rotator (PCR) on the SOI platform, to realize a multiplexing for 2N wavelengths with a spacing of Δλ. The (N + 1) × (N + 1) AWG works at a bidirectional way to provide two groups of N × 1 wavelength multiplexing with each group having a channel spacing of 2×Δλ, and the central wavelengths of all input channels in one group have a wavelength shift of Δλ with respect to those in the other group. The double channel spacing results in a significant decrease on the footprint of the (N + 1) × (N + 1) AWG-based multiplexer compared with a conventional 2N × 1 AWG multiplexer with the same wavelength spacing Δλ. Due to the fact that a single mode fiber is insensitive to the polarization of input light, if we consider short reach datacom applications such as 100/400 GbE, the two separate multiplexing outputs of the (N + 1) × (N + 1) AWG can be combined as one output with one half wavelengths working at TE polarization and the other at TM polarization by employing a low loss and broadband PCR. In the experiment, we demonstrate a 16 × 200 GHz multiplexer based on a 9 × 9 AWG. The experimental results show that the on-chip loss of the fabricated multiplexer is 2.7 dB and the loss uniformity is 0.5 dB. The 1-dB and 3-dB bandwidths are >0.56 nm (i.e., 35% of the wavelength spacing) and >1.1 nm (i.e., 69% of the wavelength spacing), respectively. They can also be further increased by decreasing the gap between adjacent input waveguides at the interfaces of star couplers of the designed AWG without inducing an excess loss. The proposed multiplexer has great potential for application to future super large capacity (> Tb/s) data transmission systems.
Compact waveguide devices based on multimode interference by using area modulation method

Xiaoqing Jiang,Haifeng Zhou,Jianyi Yang,Minghua Wang

2006-01-01

Abstract:Based on the overlapping-imaging characteristics of the multimode interference (MMI) and the method of area modulation, this paper presents several compact waveguide devices of MMI structure, such as variable optical attenuator, splitter and spatial optic logic coder. A full shuffle 1 × 3 switch and a three-channel wavelength 3 × 3 router switch with only one compound modulation region are proposed and analyzed. The characteristics of the switch devices have been demonstrated by 2-D BPM simulation. The simulation extinction ratio is higher than 30 dB for 1545, 1550 and 1555 wavelength.
Recent Advances in InP-based Waveguide Grating Demultiplexers

Koteles, E.S.,He, J.J.,Lamontagne, B.,Delage, A.

DOI: https://doi.org/10.1109/ofc.1998.657225

1998-01-01

Abstract:Summary form only given. We present detailed modeling and experimental results for an improved design of an InGaAsP/InP wavelength demultiplexer based on a monolithically-integrated Rowland circle waveguide grating fabricated using chemically-assisted ion beam etching. The design incorporates ten wavelength channels at 1.55 /spl mu/m with a uniform spacing of 2 nm and multimode output waveguides to flatten channel response and reduce sensitivity to polarization.
Recent Advances in InP Planar Waveguide DWDM Technology

JJ He

DOI: https://doi.org/10.1364/ipr.2000.ifb3

2000-01-01

Abstract:Get PDF Email Share Share with Facebook Tweet This Post on reddit Share with LinkedIn Add to CiteULike Add to Mendeley Add to BibSonomy Get Citation Copy Citation Text J. He, "Recent Advances in InP Planar Waveguide DWDM Technology," in Integrated Photonics Research, T. Li, ed., Vol. 45 of OSA Trends in Optics and Photonics (Optica Publishing Group, 2000), paper IFB3. Export Citation BibTex Endnote (RIS) HTML Plain Text Citation alert Save article
Two-dimensional wavelength demultiplexing employing multilevel arrayed waveguides.

Jianyi Yang,Xiaoqing Jiang,Minghua Wang,Yuelin Wang

DOI: https://doi.org/10.1364/OPEX.12.001084

IF: 3.8

2004-01-01

Optics Express

Abstract:Two-dimensional (2D) optical wavelength demultiplexing is demonstrated by employing multilevel arrayed waveguides as a 2D diffraction grating, named the 2D arrayed waveguide grating (2D-AWG). Since the monochromatic lightwave is diffracted by the 2D-AWG to a series of periodic spots with 2D diffraction orders in both x and y directions while the dispersion direction is never parallel to the x or y direction, we can obtain 2D wavelength demultiplexing exploiting diffraction orders of either the x or y direction. One of the two dispersion components is designed much larger than the other, and the correspondent spatial free spectral range component is set properly to ensure high diffraction efficiency. The input and output ports can also be designed based on the multilevel lightwave circuit (MLC), and their level planes can be tuned parallel to that of the MLC-based 2D-AWG, which makes it feasible to integrate the 2D-AWG with the input port and/or the output port. It provides a promising way to realize large-scale and high-density optical multiplexers/demultiplexers. (C) 2004 Optical Society of America.
Waveguide Components Based on Multiple-Mode Resonators: Advances in Microwave Multiple-Mode Waveguide Components, Including Multiplexers, Three-State Diplexers, Crossovers, and Balanced/Unbalanced Elements

Sai-Wai Wong,Jing-Yu Lin,Yang Yang,Zai-Cheng Guo,Lei Zhu,Qing-Xin Chu

DOI: https://doi.org/10.1109/mmm.2020.3035863

IF: 3.0619

2021-02-01

IEEE Microwave Magazine

Abstract:Waveguide components have been widely explored for several decades, due to their inherent merits of low insertion losses, high quality (<italic>Q</italic>) factors, and a significant power-handling capacity. Historically, cavity-based narrowband filters and multiplexers have been explored and designed for base stations and satellite applications. Compared with using single-mode resonators (SMRs), the implementation of multiple-mode resonators (MMRs) in waveguide structures is a promising solution to dramatically reduce the circuit volume and improve the frequency selectivity. Taking advantage of MMR techniques, various innovative waveguide structures have been proposed for a wide range of application scenarios. This article presents an overview of advances in microwave multiple-mode waveguide components, including narrow-, wide-, and multiband filters; multiplexers; three-state diplexers; crossovers; and balanced/unbalanced elements. Representative examples and their results are comprehensively discussed and summarized.

telecommunications,engineering, electrical & electronic
Silicon Photonic Devices for Wavelength/Mode/Polarization Multiplexing

Tao CHU,Defen GUO,Weike WU

DOI: https://doi.org/10.3969/j.issn.1009-6868.2017.05.006

2018-01-01

Abstract:In this paper,various silicon photonic devices designed for wavelength/mode/polarization multiplexing/demultiplexing are proposed,including arrayed waveguide grating (AWG) and etched diffraction grating (EDG),mode Mux/DeMux devices,polarization splitting grating coupler,and polarization splitting rotating device. With these novel devices,the following results can be achieved: (1) AWG could be formed by single step etching process; (2) EDG insertion loss is greatly reduced; (3) mode splitting device bandwidth increases,while the insertion loss is reduced; (4) the coupling efficiency of the polarization splitting grating coupler is effectively improved;(5) the insertion loss and bandwidth of the polarization splitting rotating device are also significantly improved. It is believed that the Mux/DeMux technologies on dimensions of wavelength/mode/polarization will be strongly supported by these silicon photonic devices,which are compatible with complementary metal oxide semiconductory (CMOS)-180 nm processing technologies.
A planar waveguide demultiplexer with a flat passband, sharp transitions and a low chromatic dispersion

Jun Song,Dongqing Pang,Sailing He

DOI: https://doi.org/10.1016/j.optcom.2003.09.025

IF: 2.4

2003-01-01

Optics Communications

Abstract:A flat-topped planar waveguide demultiplexer with a low chromatic dispersion is designed. A parabolic multimode interference (MMI) section with a reshaping taper is connected at the end of the input waveguide. A 16-channel etched diffraction grating (EDG) demultiplexer with channel spacing of 100 GHz is considered as a design example. Wide-angle beam propagation method and the Kirchhoff diffraction theory are used in the simulation. The field distribution at the end of the taper is reshaped optimally to have sharp transitions. A genetic algorithm is used to optimize the parabolic MMI section. The designed EDG demultiplexer has an excellent flat-topped spectral response and a very low chromatic dispersion characteristic.
Inverse Design of a Wavelength (de)multiplexer for 1.55- and 2-Μm Wavebands by Using a Hybrid Analog-Digital Method

Xuyu Deng,Aolong Sun,Qiyuan Yi,Guanglian Cheng,Sizhe Xing,Jianyang Shi,Ziwei Li,Chao Shen,Yi Zou,Li Shen,Junwen Zhang,Nan Chi

DOI: https://doi.org/10.1109/jlt.2024.3386668

IF: 4.7

2024-01-01

Journal of Lightwave Technology

Abstract:Recently, the emerging 2-mu m waveband has gained increasing interest due to its great potential for a wide scope of applications. The 2-mu m waveband is considered a novel communication window with distinct advantages of lower signal loss, better fabrication tolerance and broader gain bandwidth. Considering the advantages of 2-mu m waveband, wavelength division multiplexing of 1.55- and 2-mu m wavebands is one of the effective means to solve the current communication capacity crisis. Therefore, wavelength (de)multiplexer for 1.55- and 2-mu m wavebands is a crucial component. However, traditional design methods make it challenging to create a wavelength (de)multiplexer with a large bandwidth and compact footprint. Here, we proposed and experimentally demonstrated a wavelength demultiplexer for 1.55- and 2-mu m wavebands with an ultra-compact footprint of 3 x 3 mu m(2) utilizing an inverse design method called hybrid analog-digital algorithm to reduce computational cost and improve the device performance. Based on this algorithm, we further created three adjustable optimization parameters to achieve optimal device performance. We provide detailed explanations for the selection of these optimization parameters. The designed device has experimentally achieved a bandwidth of 100 nm for 1.55- and 2-mu m wavebands, with the insertion loss less than 1.2 and 0.9 dB, and the crosstalk less than -17.7 and -16.4 dB, respectively. Furthermore, based on a fabricated wavelength division multiplexing chip, we demonstrated a dual-waveband data transmission system that achieved a data rate of 138 Gbps at 1550 nm and 84 Gbps at 2004 nm, drawing a promising application for high-speed optical communications in the future.
Subwavelength grating devices for optical on-chip multiplexing

Lu Liu,Zhiping Zhou

DOI: https://doi.org/10.1117/12.2503322

2018-01-01

Abstract:The multiplexing technology is an effective approach to enhance the capacity of optical communication system while numerous kinds of multiplexing devices have been proposed. Subwavelength gratings (SWGs) are periodic structures with pitches small enough to locally synthesize the refractive index. This talk provides an introduction to the basics of SWG and particularly focuses on the design strategies of some SWG based devices in multiplexing system, including polarization independent directional coupler, polarization beam splitter and wavelength multiplexer. With SWG to engineer the refractive index, birefringence and dispersion, these devices possess more design freedoms and exhibit a better performance.
Bidirectional Arrayed Waveguide Grating (de)multiplexer Integrated with an Optical Interleaver for Doubling the Channels

Sitao Chen,Xin Fu,Yaocheng Shi,Sailing He,Daoxin Dai

DOI: https://doi.org/10.1364/acpc.2014.ath1a.2

2014-01-01

Abstract:A novel wavelength division multiplexers is designed and demonstrated to achieve doubled channel number and halved channel spacing for an arrayed-waveguide grating by utilizing an optical interleaver integrated.
Experimental demonstration of simultaneous mode and polarization-division multiplexing based on silicon densely packed waveguide array.

Kaixuan Chen,Siya Wang,Sitao Chen,Shipeng Wang,Chenzhao Zhang,Daoxin Dai,Liu Liu

DOI: https://doi.org/10.1364/OL.40.004655

IF: 3.6

2015-01-01

Optics Letters

Abstract:A silicon mode and polarization-division multiplexing scheme based on a densely packed waveguide array structured as a bus waveguide is introduced. A short adiabatic taper is adopted for (de) multiplexing. Such a structure shows theoretical insertion losses that are <0.05 dB and crosstalk that is <- 20 dB over a wide wavelength band for all five supported modes. The structures for (de) multiplexing are fabricated and characterized experimentally. A device, which consists of a multiplexer, a 50-mu m-long straight-bus waveguide, and a demultiplexer, exhibits insertion losses that are <0.6 dB and crosstalk that is <- 15 dB over an 80 nm wavelength band. The demonstrated (de) multiplexer has a total length of 60 mu m, and the bus waveguide has an effective width of 1.58 mu m. (C) 2015 Optical Society of America

Planar Waveguide Multiplexers/Demultiplexers in OpticalNetworks: from ImprovedDesigns to Applications

Design and Numerical Optimization of A Mode Multiplexer Based on Few-Mode Fiber Couplers

Design of an Ultracompact MMI Wavelength Demultiplexer in Slot Waveguide Structures.

2D-Awg-based Optical Multiplexers/Demultiplexers

Integrated Waveguide WDM Demultiplexers

Design of Hybrid Free-Space Wavelength-Division Multiplexers for Integration

Design and simulation of a planar integrated demultiplexer for coarse WDM

Multifunctional Optical Waveguide Chips

Propagation Characteristic Analysis and Applications of Spatial Four-Waveguide System

Novel Wavelength Multiplexer Using (<italic>N</italic> + 1) × (<italic>N</italic> + 1) Arrayed Waveguide Grating and Polarization-Combiner-Rotator on SOI Platform

Compact waveguide devices based on multimode interference by using area modulation method

Recent Advances in InP-based Waveguide Grating Demultiplexers

Recent Advances in InP Planar Waveguide DWDM Technology

Two-dimensional wavelength demultiplexing employing multilevel arrayed waveguides.

Waveguide Components Based on Multiple-Mode Resonators: Advances in Microwave Multiple-Mode Waveguide Components, Including Multiplexers, Three-State Diplexers, Crossovers, and Balanced/Unbalanced Elements

Silicon Photonic Devices for Wavelength/Mode/Polarization Multiplexing

A planar waveguide demultiplexer with a flat passband, sharp transitions and a low chromatic dispersion

Inverse Design of a Wavelength (de)multiplexer for 1.55- and 2-Μm Wavebands by Using a Hybrid Analog-Digital Method

Subwavelength grating devices for optical on-chip multiplexing

Bidirectional Arrayed Waveguide Grating (de)multiplexer Integrated with an Optical Interleaver for Doubling the Channels

Experimental demonstration of simultaneous mode and polarization-division multiplexing based on silicon densely packed waveguide array.