Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Temperature Dependency of Water Vapor Permeability of Shape Memory Polyurethane

A Molecular Dynamics Investigation of the Deformation Mechanism and Shape Memory Effect of Epoxy Shape Memory Polymers

Moisture-Responsive Shape Memory Polymers and Their Composites

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Effect of soft segment structure on properties of polyurethane elastomers

The temperature-sensitive water vapor permeation control of polyurethane membrane using the graft-polymerized poly(N-isopropylacrylamide) and the impact on the tensile strength and shape recovery effect

Preparation and properties of shape memory polyurethane filaments triggered by human body temperature

Effects of Temperature and Moisture on Concrete-PCM Interface Performance

Heating‐Responsive Shape‐Memory Effect in Thermoplastic Polyurethanes with Low Melt‐Flow Index

Insight into the Origin of the Thermosensitivity of Poly[2-(Dimethylamino)ethyl Methacrylate].

Understanding water absorption effect on molecular dynamics, microstructures and relaxation behavior of segmented polyurethane elastomers

Study on structure-induced heat transfer capabilities of waterborne polyurethane membranes

Rational Design of Waterborne Polyurethane Pressure Sensitive Adhesives for Different Working Temperatures

Synthesis and Characterization of Polyurethane‐Based Shape‐Memory Polymers for Tailored Tg Around Body Temperature for Medical Applications

Absorption and Permeation of Water and Aqueous Solutions of High-Temperature Vulcanized Silicone Rubber

Water Vapor Transport Properties of Polyurethane Films for Packaging of Respiring Foods

Preparation and Characterization of Body-Temperature-Responsive Thermoset Shape Memory Polyurethane for Medical Applications

Understanding the shape-memory mechanism of thermoplastic polyurethane by investigating the phase-separated morphology: A dissipative particle dynamics study

Characterization of Polyurethane Shape Memory Polymer and Determination of Shape Fixity and Shape Recovery in Subsequent Thermomechanical Cycles

Change in Mechanical Properties, Composition, and Structure of Hydrated Polyurethaneurea

A Study on the 3D Deformation Behavior of Porous PDMS Flexible Electronic Composite Films Stretched under Different Temperatures