Abstract:Anion exchange membrane water electrolysis (AEMWE) is operated in an alkaline environment and has a similar membrane-electrode assembly (MEA) structure to that of proton exchange membrane water electrolysis (PEMWE). The use of non-noble metals as the electrocatalysts and operation at high current densities are inherently possible, so they are expected to be low-cost, high-performance candidates for next-generation water electrolysis systems. Improving the anion conductivity of the AEM and the activity of the non-precious metal catalysts is essential for the practical application of AEMWEs. 1 The non-noble electrocatalysts used in the MEA in this study were Ni 0.8 Co 0.2 O 2 and Ni 0.8 Fe 0.2 O, 3 which have a fused-aggregate network structure, and the electrolyte was a hydrocarbon-based AEM (QPAF-4) 4 , all of which were developed at the University of Yamanashi. The catalyst ink for the anodes was prepared by mixing the Ni 0.8 Co 0.2 O catalyst (University of Yamanashi) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 , University of Yamanashi) binder solution. The anode ink was coated by using pulse-swirl-spray (PSS, Nordson) on the QPAF-4 membranes (IEC = 1.5 meq g -1 ) to make the catalyst-coated membranes (CCMs) with the anode. Catalyst inks for the cathodes was prepared by mixing Ni 0.8 Fe 0.2 O catalyst (University of Yamanashi) or Pt/CB catalyst (TEC10E50E, Tanaka Kikinzoku) with solvent (water/methanol) and QPAF-4 (IEC = 2.0 meq g -1 ) binder solution. The cathode ink was coated by using PSS on the gas diffusion layer (GDL, TGP-H-120, Toray) to make the gas diffusion electrodes (GDEs) for the cathodes. Ni mesh (Bekaert.co.jp) was used for the anode GDLs. The single cell (Figure 1, cell structure developed by Yokohama National University) performances were measured while supplying 1 M KOH at 80 °C to both electrodes. Figure 2 (a) shows the I-V performance of cells using Ni 0.8 Co 0.2 O for the anode and Ni 0.8 Fe 0.2 O or Pt/CB for the cathode. The electrolysis voltage observed for the cell with non-noble metal catalysts on both electrodes was higher than that for the cell with Pt/C on the cathode but was below 2 V at a current density of 1.2 A cm -2 . The value of the onset electrolysis voltage was nearly the same as that of the corresponding rotating disk electrode, 3 suggesting that the intrinsic performance of the cathode catalyst is being realized in the MEA. Increasing the amount of the cathodic catalyst loading scarcely affected the polarization. It is supposed that the fused-aggregate network structure of the Ni 0.8 Fe 0.2 O catalyst contributes to the favorable mass transfer. Figure 2 (b) shows the time dependence of the cell voltage of these cells. The increased loading amount improved the durability of the cathode. It is considered that the increase in the thickness of the cathode catalyst layer alleviated the damage of the GDL fibers to the membrane. These results indicate the possibility of adopting non-precious metal catalysts for both electrodes in AEMWE and thereby significantly reducing the catalyst cost. Acknowledgement This work was partially supported by NEDO of Japan through the AWE-1 project. References 1) A. Lim et al., J. Ind. Eng. Chem ., 76 , 410 (2019). 2) G. Shi et al., ACS Catal ., 12 , 14209 (2022). 3) G. Shi et al., ACS Omega , 8 , 13068 (2023). 4) H. Ono et al., J. Mater. Chem . A , 5 , 24804 (2017). Figure 1

Electrically Insulated Catalyst-Ionomer Anode Interfaces towards Durable Alkaline Membrane Electrolyzer

(Invited) Passivated Anodes in Anion-Exchange Membrane Water Electrolyzers

(Invited) Catalyst and Anode Design for Durable Alkaline-Membrane Electrolysis

Understanding How Anion Exchange Membranes and Cationic Polymer/Catalyst Interactions Behave with Time in Alkaline Electrolysis

Performance and Durability of Membrane-Electrode Assemblies Using Non-Precious Metal Catalyst and a Hydrocarbon-Based Electrolyte for Anion Exchange Membrane Water Electrolysis

One-Step Synthesis of Selective Nife-Layered Double Hydroxide Anode Catalyst for Highly Efficient and Stable Anion Exchange Membrane Water Electrolyzers, Operating with Seawater

Pathways Toward Efficient and Durable Anion Exchange Membrane Water Electrolyzers Enabled By Electro‐Active Porous Transport Layers

High-Performing Anion Exchange Membrane Water Electrolysis Using Self-Supported Metal Phosphide Anode Catalysts and an Ether-Free Aromatic Polyelectrolyte

High Performance AEM Water Electrolysis with Aemion® Membranes

Anion Exchange Ionomers Enable Sustained Pure-Water Electrolysis Using Platinum-Group-Metal-Free Electrocatalysts

Investigation of Electrocatalyst and Ionomer Interaction in Anion Exchange Membrane Water Electrolysis

Understanding the Effects of Anode Catalyst Conductivity and Loading on Catalyst Layer Utilization and Performance for Anion Exchange Membrane Water Electrolysis

AEM Water Electrolysis with Ni-Based Catalysts and Tailored Poly(arylene piperidinium) Materials for Improved Stability

Translating the Optimized Durability of Co‐Based Anode Catalyst into Sustainable Anion Exchange Membrane Water Electrolysis

Durability and Performance of Poly(norbornene) Anion Exchange Membrane Alkaline Electrolyzer with High Ionic Strength Anolyte

Three-Dimensional Unified Electrode Design Using a NiFeOOH Catalyst for Superior Performance and Durable Anion-Exchange Membrane Water Electrolyzers

Limitations and Opportunities of Self-Supported Co-Based Anodes for Pure Water-Fed Anion Exchange Membrane Water Electrolyzers

Effect of catalyst layer designs for high-performance and durable anion-exchange membrane water electrolysis

Composite anion exchange membranes based on polysulfone and silica nanoscale ionic materials for water electrolyzers

Investigation of Ionomer and Catalyst (Co 3 O 4 , Mn 3 O 4 , or MnO 2 ) Interactions Using a Polyethylene Midblock Copolymer in Anion Exchange Water Electrolyzers to Understand Performance and Durability

Revolution of Electrode Design Toward Oxygen Evolution Reaction for Anion Exchange Membrane Water Electrolysis