Abstract:J ETS impinging normally on a flat plate have been extensively studied in terms of flow characteristics, wall temperature, and pressure distribution [1,2]. In some cases, a jet impinges on the plate with a certain degree of inclination with respect to the plate, resulting in the oblique impinging jet. In the case of a jet removing heat from the target plate (cooling jet), it has been established that the location ofmaximumheat transfer shifts increasingly toward the uphill side of the plate, and the maximum Nusselt number decreases as the inclination angle is decreased from the normal impinging position [3,4]. On the contrary, for a heating jet, such an inclination increases the maximum temperature (or heat transfer rate), leading to a significant temperature jump at all the points along the plate [5]. The upward shift of the maximum temperature is attributed to the reduction in effective entrainment of air on both the uphill and downhill sides of the target plate. Although a multitude of studies have been conducted to characterize theflowand heat transfer characteristics of an impinging jet [1– 7], there has not yet been a study devoted to the thermal stresses induced on the target plate by an inclined impinging heating jet. Several systems, including welding, laser heating, and electric discharge machining (EDM), are similar to the impinging heating jet in terms of heat transfer to the target plate and consequently have akin temperature profiles. Yadav et al. [8] used the Galerkin finite element formulation to simulate the EDM-induced temperature and thermal stresses on a target plate. High temperature gradient zones were found to correspond to regions of large stresses that may exceed the material yield strength. Sunar et al. [9] analyzed the temperature and thermal stresses developed in a sheet metal due to welding. The thermal stresses were found to be compressive in nature and follow a trend similar to the temperature distribution due to the high gradients near the center. The present study is concerned with the thermal stresses developed on a flat plate, due to an impinging heating slot jet, and their variation with jet inclination. For fixed separation distance and Reynolds number, and selected jet inclination angles, the measured temperature data are used as input for thermal stress modeling, using the sequential coupling finite element method (FEM). For a given set of thermal boundary conditions, thermal stresses are calculated for various inclination angles and physical boundary conditions of the plate. The study is limited to the steady-state responses of temperature and thermal stresses.

Experimental Study on Temperature Fluctuations on Plate Surface Induced by Coaxial-Jet Flow

Numerical Study on Thermal Stress Fluctuation Caused by Coaxial-Jet Flow in Lower Head of Central Measurement Column

Experimental Investigation On Critical Heat Flux From Downward Facing Flat Plate For Different Orientation Angles

Experimental Investigation on Heat Transfer Characteristics in a Safety Injection Nozzle Component in PWR

Influence of corrugated jet plates on internal heat transfer and flow dynamics of double-wall cooling: experimental-numerical approach

Numerical Simulation of Heat Transfer and Fluid Flow of a Non-Equilibrium Argon Plasma Jet with Confined Wall

Thermal Stress Induced by Inclined Impinging Heating Jet on A Flat Plate

Transverse Buoyant Jet-Induced Mixed Convection Inside a Large Thermal Cycling Test Chamber with Perforated Plates

HEAT TRANSFER AND FLUID FLOW FOR A THERMAL PLASMA JET IMPINGING NORMALLY ON A FLAT PLATE

Numerical Simulation of the Flow and Heat Transfer Characteristics of Sweeping and Direct Jets on a Flat Plate with Film Holes

Study of Jet Characteristics and Structural Fatigue in the Upper Chamber of a Lead-Bismuth Eutectic Cooled Reactor Based on Fluid-Structure Coupling Methods

Experimental Study on High-Energy Fluid Jets from a Pipe: Jet Cone Morphology and Impact Force on Flat Plates

Investigation of Thermal Striping in Prototype Fast Breeder Reactor Using Ten-Jet Water Model

Numerical investigation on conjugate behavior of heat transfer and its augmentation in a turbulent wall-jet flow on a heated plate in motion

Effect of Reynolds Number, Hole Patterns, Target Plate Thickness on Cooling Performance of an Impinging Jet Array: Part Ii - Conjugate Heat Transfer Results and Optimization

Experimental Investigation on Thermal Stratification in A Pressurizer Surge Line with Different Arrangements

Comparative Study Of Impinging Jet Array Heat Transfer On A Flat Plate Cooled By Superheated Steam And Air

Flow boiling heat transfer and pressure fluctuation characteristics in a divergent channel with inclined downward-facing heater

Thermal fatigue analysis of structures subjected to liquid metal jets at different temperatures in the Gen-IV nuclear energy system

Jet impingement heat transfer performance in a double-wall cooling structure with film effusion holes and pin fins

Numerical investigation on the heat transfer performance of array jet impingement cooling with sinusoidal-corrugated target plate