Abstract:Predicting pressure drop in gas wells is one of the most important issues for designing deliquification technologies and optimizing gas production. Current pressure-drop prediction methods can be divided into analytical and empirical models. Although various models have been proposed to predict pressure drop in wellbores, no model has offered stable performance over wide liquid and gas flowrate ranges. Especially for gas wells with low liquid – gas ratios, very few models have been developed specifically. In this study, a simple and accurate three-point model is developed for predicting liquid holdup in wellbores. The model is based on the liquid holdups and gas velocities at the annular – churn, churn – slug and slug – bubble boundaries and is comprehensive for calculating the liquid holdup in vertical wellbores at different liquid/gas flowrates and pressures. The proposed method was verified with 39 collected laboratory and 182 field measured data points from the literature, which have wide parameter ranges. For comparison, some widely used models in the petroleum industry were also evaluated. In validation with the laboratory data with pipe diameters of 50.8 and 101.6 mm, although the new model has an average percentage error ( E 3) of 220.1% in the churn flow, ranking fourth of all the evaluated models, the other five indicators in the churn flow and six indicators in the annular flow are lowest of all these evaluated models, resulting in relative performance factors (RPFs) of 0.2 and 0, respectively. In the field measured data, gas and liquid productions range between 0.34 × 10 4 —77.6 × 10 4 m 3 /d and 1—347.8 m 3 /d, tubinghead pressure ranges from 0.7 to 84.7 MPa, which can cover most gas wells. The validation demonstrates that the new model still has good performance with five indicators being lowest. The RPF of the new pressure-drop model in the field measured data ranges is 0.29, still lowest of all these evaluated models, showing better performance than these widely used models in petroleum industry for vertical gas wells. This indicates that the new model can accurately predict pressure drop under different conditions in vertical gas wells.

N‐shape pressure drop curve of gas–liquid microchannel reactor and modeling

Numerical simulation on pressure drop of slush nitrogen flow inside a horizontal pipe

PRESSURE FLUCTUATIONS OF LIQUID-LIQUID SLUG FLOW IN CROSS-JUNCTION SQUARE MICROCHANNELS

A General Pressure Drop Model Based on Liquid Holdup of Gas-Liquid Flow in Micro-Packed Beds

Dynamic Pressure Drop Property of Gas-Liquid Two-Phase Flow around a Horizontal Cylinder

Effect of Liquid Properties on Frictional Pressure Drop in a Gas-Liquid Two-Phase Microchannel

The gas–liquid mass transfer and pressure drop behaviors of the gas–liquid–liquid three‐phase flow in micro‐packed beds

Study of the Pressure Drop of Liquid–Liquid Slug Flow in a Circular Microchannel

Flow Pattern Study and Pressure Drop Prediction of Two-Phase Boiling Process in Different Surface Wettability Microchannel

Hydrodynamics and Mass Transfer Performance of Gas–liquid Microflow in Viscous Liquids

Hydrodynamics and Scaling Laws of Gas–Liquid Taylor Flow in Viscous Liquids in a Microchannel

Pressure drop prediction model of the gas-liquid stratified flow development section in the horizontal pipeline

Impact of the Channel- to Particle-Diameter Ratio on the Liquid-Liquid Mass Transfer and Pressure Drop in Micro Packed Bed Reactors

Study on Hydrodynamics and Mass Transfer Characteristic of a New Gas-liquid Reactor

Pressure Drop for Gas and Polymer Aqueous Solution Two-Phase Flows in Horizontal Circular Microchannel

Pressure drop for subcooled water boiling in microchannels under high heat fluxes: Experiments and predictions from artificial neural networks

Experimental Investigation of Adiabatic Gas-Liquid Flow Regimes and Pressure Drop in Slit Microchannel

Friction pressure drop model of gas-liquid two-phase flow in an inclined pipe with high gas and liquid velocities

Effect of Viscosity on Liquid–Liquid Slug Flow in a Step T-Junction Microchannel

Flow boiling frictional pressure drop inside micro/mini-channels: A new general model and experimental investigation

A simple and accurate model to predict pressure drop in vertical gas wells